Sharp PG-C20XE (serv.man5) Service Manual ▷ View online
9
PG-C20XU
PG-C20XE
PG-C20XE
AN-Z7T
Remote Control
Front View
Rear View
Mouse (
]
/
[
)/
Adjustment (
]
/
[
)
buttons
Mouse (
>
)button
Mouse (
<
)button
MOUSE button
FREEZE button
MENU button
INPUT button
KEYSTONE buttons
VOLUME buttons
POWER button
RIGHT-CLICK/
ENTER button
ENTER button
ENLARGE button
AUTO SYNC button
AV MUTE button
RESIZE button
GAMMA button
Flip cover
LEFT-CLICK/
BACK button
BACK button
Opening the Flip Cover
3
Press the tab and lift open
the battery cover in the
direction of the arrow.
the battery cover in the
direction of the arrow.
Insert two AAA size
batteries,making sure
their polarities match the
batteries,making sure
their polarities match the
+ and - marks inside
the battery compartment.
Inserting the Batteries
Insert the tabs on the
end of the battery cover
into their slots and press
the cover into position.
end of the battery cover
into their slots and press
the cover into position.
1
2
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the batteries.
• Do not mix new and old or different types of batteries.
• There are operations that can only be carried out by remote control. Handle the remote control carefully.
• Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the batteries.
• Do not mix new and old or different types of batteries.
• There are operations that can only be carried out by remote control. Handle the remote control carefully.
10
PG-C20XU
PG-C20XE
PG-C20XE
AN-Z7T
Using the Wireless Mouse
Remote Control/Mouse Receiver Positioning
The remote control can be used to control the projector within the ranges shown below.
The remote mouse receiver can be used with the remote control to control the mouse functions of a connected
computer within the ranges shown below.
The remote mouse receiver can be used with the remote control to control the mouse functions of a connected
computer within the ranges shown below.
The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the
signal may differ due to the screen material.
signal may differ due to the screen material.
Controlling the Projector
Using as a Wireless Mouse
When MOUSE is pressed, the buttons on the remote
control light up and the remote control enters MOUSE
mode.
During MOUSE mode, the cursor can be used as the
pointer. MOUSE mode is for about ten seconds while
the buttons are lighting.
When MENU or ENLARGE is pressed, MOUSE mode
is released to the normal mode.
Be sure the supplied remote mouse receiver is
connected to your computer.
control light up and the remote control enters MOUSE
mode.
During MOUSE mode, the cursor can be used as the
pointer. MOUSE mode is for about ten seconds while
the buttons are lighting.
When MENU or ENLARGE is pressed, MOUSE mode
is released to the normal mode.
Be sure the supplied remote mouse receiver is
connected to your computer.
The wireless mouse may not operate correctly if your
computer serial port is not correctly set up. Refer to the
computer s operation manual for details of setting up/
installing the mouse driver.
For one-button mouse systems, use either the LEFT-CLICK
or RIGHT-CLICK button.
computer serial port is not correctly set up. Refer to the
computer s operation manual for details of setting up/
installing the mouse driver.
For one-button mouse systems, use either the LEFT-CLICK
or RIGHT-CLICK button.
Effective buttons in MOUSE mode
Remote control
(Front view)
Remote control
(Rear view)
Mouse
RIGHT-CLICK
AV MUTE
LEFT-CLICK
MOUSE
30ß
45ß
23’ (7 m)
30ß
45ß
30ß
Remote control
Remote
mouse
receiver
mouse
receiver
13’ (4 m)
30ß
30ß
120ß
Remote control
Remote control
11
PG-C20XU
PG-C20XE
PG-C20XE
AN-Z7T
Connection Pin Assignments
COMPUTER INPUT 1 Port: 15-pin mini D-sub female connector
Computer Input
Analog
1. Video input (red)
2. Video input
2. Video input
(green/sync on green)
3. Video input (blue)
4. Not connected
5. Composite sync
6. GND (red)
7. GND (green/sync on green)
8. GND (blue)
4. Not connected
5. Composite sync
6. GND (red)
7. GND (green/sync on green)
8. GND (blue)
9. Not connected
10.Not connected
11. GND
12.Bi-directional data
13.Horizontal sync signal
14.Vertical sync signal
15.Data clock
10.Not connected
11. GND
12.Bi-directional data
13.Horizontal sync signal
14.Vertical sync signal
15.Data clock
5
5
6
9
9
8
7
3
4
1
2
6
5
1
10
15
1
6
11
6
11
RS-232C Terminal: 9-pin Mini DIN female connector
RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable
Pin No.
Signal
Name
I/O
Reference
1
Not connected
2
RD
Receive Data
Input
Connected to internal circuit
3
SD
Send Data
Output
Connected to internal circuit
4
Not connected
5
SG
Signal Ground
Connected to internal circuit
6
Not connected
7
Not connected
8
Not connected
9
Not connected
Pin No.
Signal
Name
I/O
Reference
1
Not connected
2
RD
Receive Data
Input
Connected to internal circuit
3
SD
Send Data
Output
Connected to internal circuit
4
Not connected
5
SG
Signal Ground
Connected to internal circuit
6
Not connected
7
Not connected
8
Not connected
9
Not connected
12
PG-C20XU
PG-C20XE
PG-C20XE
AN-Z7T
Dimensions
Unit: inches (mm)
Rear View
Top View
Front View
Bottom View
Side View
8 / (207)
5
32
6 / (169.5)
43
64
/ (8)
5
16
1 / (42)
21
32
1 / (32)
17
64
3 / (82)
15
64
10 / (260)
15
64
2 / (58)
9
32
4 / (118)
21
32
Click on the first or last page to see other PG-C20XE (serv.man5) service manuals if exist.