DOWNLOAD Sharp PG-C20XE (serv.man5) Service Manual ↓ Size: 887.77 KB | Pages: 30 in PDF or view online for FREE

»

Using the set's control switch or the remote control-
ler’s button, adjust the setting so that the flickering
be minimum.

»

Adjust the setting so that the image comes to the
center of the screen.

1. Feed the countervoltage

adjustment signal. (XGA)

2. Select the following group,

sub-group and subjects.
Group : LCD2 (6050)
Sub-group: COM
Subject :

R_LCCOM (In R adjustment)
G_LCCOM (In G adjustment)
B_LCCOM (In B adjustment)
R_REVLCCOM (In R re-
verse adjustment)
G_REVLCCOM (In G re-
verse adjustment)
B_REVLCCOM (In B re-
verse adjustment)

»

Adjust the AMP-BLK setting so that the gradation of
the part 

1

 (white 95% and 100%) as shown in the

figure below is barely discernible.

»

Make sure that the gradation of the part 

2

 (black

0% and 5%) is also discernible.

1. Feed the green-only

SMPTE pattern signal.
(XGA)

2. Select the following

group, sub-group and
subject.
Group : Adjust PC Image
Sub-group: CXA2111R
Subject : AMP-BLK

1

2

1. Feed the 32-step gray-

scale signal. (XGA)

2. Select the following group,

sub-group and subjects.
Group : Adjust PC Image
Sub-group: CXA2111R
Subject : AMP-R-BLK

(In R adjustment)
AMP-B-BLK
(In B adjustment)

»

Adjust the setting to achieve the best color tone
balance.

1. Feed the NTSC

monoscope signal.

2. Select the following

group, sub-group and
subject.
Group

: Adjust VIDEO Image

Sub-group: VPC3230
Subject : H-Position

»

Make sure the setting is 52.

1. Feed the NTSC 10-step

signal.

2. Select the following group,

sub-group and subject.
Group : Adjust VIDEO Image
Sub-group: VPC3230
Subject : Contrast

3. Connect the synchroscope

to TP1402.

»

First reach a setting where the color tone level 10
gets saturated. Then decrease the setting by one
point.

1. Feed the color bar signal.
2. Select the following group,

sub-group and subject.
Group : Adjust VIDEO Image
Sub-group: VPC3230
Subject : Color

»

Make sure the setting is 128.

0-gradation

10-gradation

0.8Vp-p

1. Feed the NTSC 10-step

signal.

2. Select the following group,

sub-group and subject.
Group : Adjust VIDEO Image
Sub-group: VPC3230
Subject : Bright

»

Make sure the setting is as shown below.
PG-C20XU ........ 142
PG-C20XE ........ 145

1. Select the following group,

sub-group and subjects.
Group : Adjust VIDEO image
Sub-group: CXA2111R
Subject : PRGLEV

SIDLEV

2. Connect the synchroscope

to TP1210.

3. Using the NTSC 10-step

input signal, make sure that
there is no vertical stripes
appearing every 12 dots. (If
white or black vertical
stripes appear, fine-adjust
the SIDLEV setting.)

PSIG

»

Make sure the setting is as shown below.
PRGLEV ........... 61
SIDLEV ............. 170

1. Select the following group,

sub-group and subjects.
Group : Adjust VIDEO image
Sub-group: CXA2111R
Subject :

AMP-R-Gain (In R adjustment)
AMP-R-BLK  (In R adjustment)
AMP-G-Gain (In G adjustment)
AMP-G-BLK  (In G adjustment)
AMP-B-Gain (IN B adjustment)
AMP-B-BLK (IN B adjustment)

2. Connect the synchroscope

to the following TPs.
 In R adjustment  TP1101
 In G adjustment  TP1201
 In B adjustment  TP1301

3. Feed the NTSC 10-step

signal.

1.Select AMP-R-Gain and adjust the signal amplitude

to 3.8 

±

 0.1Vp-p.

2.Select AMP-R-BLK and adjust the white-white sig-

nal amplitude to 2.1 

±

 0.1Vp-p.

3.Select AMP-G-Gain and adjust the signal amplitude

to 3.5 

±

 0.1Vp-p.

4.Select AMP-G-BLK and adjust the white-white sig-

nal amplitude to 2.6 

±

 0.1Vp-p.

5.Select AMP-B-Gain and adjust the signal amplitude

to 3.5 

±

 0.1Vp-p.

6.Select AMP-B-BLK and adjust the white-white signal

amplitude to 2.6 

±

 0.1Vp-p.

Note: Make sure that the black side does not interfere

in Gain adjustment.

2.1Vp-p(R)

3.8Vp-p(R)

1. Feed the 32-step gray-

scale signal. (VIDEO)

2. Select the following group,

sub-group and subjects.
Group : Adjust VIDEO Image
Sub-group: CXA2111R
Subject :

AMP-R-BLK (In R adjustment)
AMP-B-BLK (In B adjustment)

»

Adjust the setting to achieve the best color tone bal-
ance.

1. Apply the automatic color

correction using the auto-
matic color irregularity cor-
rection system.

»

Make sure that no remarkable uneven color remains
on the screen.

1. Feed the color bar signal.

»

User adjustment:
Check the Color and Tint settings.

1. Feed the monoscope pat-

tern signal.

»

User adjustment:
Check the performance relating to Contrast, Bright-
ness and Sharpness.

1. Feed the audio signal.

»

User adjustment:
Check the sound volume performance.

1. Feed the RGB signal.

»

User adjustment:
Check the performance relating to Contrast, Bright-
ness, Red, Blue, Clock, Phase, H-POS, and V-POS.

1. Receive the 480I signal.

»

User adjustment:
Check the performance relating to Contrast, Bright-
ness, Color, Tint and Sharpness.

1. Heat the thermistor with a

hair dryer.

»

Make sure that the temperature is indicated.

1. Feed the phase check pat-

tern signal.

»

In the VGA, SVGA, XGA, and SXGA modes, make
sure the Clock, Phase, H-Pos and V-Pos settings can
be automatically adjusted.

»

Make sure that the keystone distortion can be cor-
rected.

»

Make sure that the brightness can be changed with
the user lamp power control.

»

Make the following settings.

Destination

Process adjustment

Remote control adjustment

(Model)

US (XU)

S4

Factory setting at 4

Europe (XE)

S4

Factory setting at 4