DOWNLOAD Sharp PG-A20X (serv.man24) Service Manual ↓ Size: 5.75 MB | Pages: 74 in PDF or view online for FREE

When using the default setting.

▼On-screen Display

The image is reversed.

When using the default setting.

▼On-screen Display

The image is inverted.

■ Place a translucent screen between the projector and the

audience.

■ Reverse the image by setting “Rear” in the “PRJ Mode” menu.

 for use of this function.

■ Place a mirror (normal flat type) in front of the lens.

•

When using a mirror, be sure to carefully position both the
projector and the mirror so the light does not shine into the
eyes of the audience.

■ It is recommended that you use the optional Sharp ceiling-

mount bracket for this installation.
Before mounting the projector, contact your nearest Sharp
Authorized Projector Dealer or Service Center to obtain the
recommended ceiling-mount bracket (sold separately).

•

AN-PGCM95 ceiling-mount bracket, its AN-EP101B
extension tube and AN-JT299 universal bracket, adaptor
for non-level ceiling installation (for U.S.A.).

•

BB-A10T ceiling adaptor, its BB-NVHOLDER280, BB-
NVHOLDER550, BB-NVHOLDER900 ceiling mount
systems (for GERMANY).

•

AN-A10T ceiling-mount bracket, its AN-TK201 and AN-
TK202 extension tubes (for countries other than the U.S.A.
and GERMANY).

■ Be sure to adjust the position of the

projector to match the distance (H)
from the lens center position (see page

when mounting the projector on the
ceiling.

■ Invert the image by setting

“Ceiling+Front” in the
“PRJ Mode” menu. See
page 

function.

PG-A20X_E_PDF_P21_25.p65

03.6.5, 11:20 AM

25

• The language preset at the factory is English.

If you want to change the on-screen display to
another language, reset the language accord-
ing to the procedure on page 

• The power indicator illuminates red, and

the projector enters standby mode.

• The power indicator illuminates green.

After the lamp indicator illuminates, the
projector is ready to start operation.

Note

• The lamp indicator illuminates,

indicating the status of the lamp.

Green: The lamp is ready.
Blinking in green: The lamp is warming

up or shutting down.

• If the projector is put into the standby

mode and immediately turned on
again, the lamp indicator may take
some time to illuminate.

• When controlling the projector using

RS-232C commands from a com-
puter, wait for at least 30 seconds af-
ter the power has been turned on, and
then transmit the commands.

• When “Anti-Theft” (see page 

the keycode input box will appear. Enter
the keycode.

Note

• When entering the keycode, press the

buttons previously set on the projec-
tor or the remote control.

• For details about the Anti-Theft func-

tion, refer to “Anti-Theft (Setting the
Anti-Theft)” on page 

▼Keycode input box

PG-A20X_E_PDF_P26_31.p65

03.4.23, 9:57 AM

26

• After pressing 

 once on the projector,

use 

 to select the desired input mode.

Note

• When no signal is received, “NO SIG-

NAL” will be displayed. When a signal
that the projector is not preset to re-
ceive is received, “NOT REG.” will be
displayed.

• The INPUT mode is not displayed

when “OSD Display” is set to “OFF”.
(See page 

Note

• Pressing 

 will lower the volume.

Pressing 

 will raise the volume.

• On the projector, the volume can be

adjusted by pressing 

 or 

.

Note

• Pressing 

 again will turn the pro-

jected image and sound back on.

"On-screen Display (Example)

Using RGB

Using
Component

INPUT 3 mode
   Using Video

INPUT 2 mode
   Using S-Video

➝

➝

➝

Used for projecting im-
ages from equipment that
sends RGB signals or
component signals con-
nected to the RGB input
terminal.

Used for projecting im-
ages from equipment
connected to the S-
VIDEO input terminal.

Used for projecting im-
ages  from equipment
connected to the VIDEO
input terminal.

INPUT 1
(RGB/
Component)

INPUT 2
(S-Video)

INPUT 3
(Video)

PG-A20X_E_PDF_P26_31.p65

03.4.23, 9:57 AM

27

• The “Picture” menu will be displayed.

Press \ or | to select the “Lan-
guage” menu icon.

• The “Language” menu will be displayed.

Press ' or " to select the desired
language, and then press 

• The desired language will be set as the

on-screen display.

STANDBY

STANDBY

Note

• If you accidentally pressed 

STANDBY

 or

STANDBY

 and do not want to put the projector

into the standby mode, wait until the con-
firmation message disappears.

• The projector cannot be operated

while a message “Shutting Down.
Please Wait.” is displayed.

• Do not unplug the power cord during pro-

jection or cooling fan operation. This can
cause damage due to rise in internal tem-
perature, as the cooling fan also stops.

', ", \, |
buttons

PG-A20X_E_PDF_P26_31.p65

03.4.23, 9:57 AM

28