DOWNLOAD Sharp MX-M904 / MX-M1204 (serv.man9) Service Manual ↓ Size: 27.84 MB | Pages: 127 in PDF or view online for FREE

MX-M1204  MX-M904/M1054/M1204 (MAIN UNIT)  2 – 5

1)

Remove the fixing tape and the protection material.

2)

Open the front cover.

3)

Remove the protection sheet and the Operation Manual. 

4)

Remove the screw (a), and remove the cover (b).

5)

Remove the protection material. (Packing material for fixing
the separation pawls)

NOTE: When moving the machine again after unpacking, be

sure to attach the protection material. (If not, the OPC
drum may be damaged.)

6)

Pull out the intermediate frame. 

a

a

b

MX-M1204  MX-M904/M1054/M1204 (MAIN UNIT)  2 – 6

7)

Remove the protection material and the caution label.

1)

Remove the included parts.

1)

Check to confirm that all the parts are provided. 

1)

Put the height adjuster plate (Packed items No.9 x4) under the
adjuster bolt at the bottom of the machine. 
Turn the adjuster bolt to adjust the height and the tilt of the
machine.

MEMO: When the adjuster bolt is turned counterclockwise, the
height is decreased. When turned clockwise, the height is
increased. (Common to the options the height of which is
adjusted by the adjuster bolt.)

NOTE: Lower the height of the MX-CF11 to the lowest position

before adjusts the level between the MX-CF11 and the
main body.

Adjust the height of the top surface of main body refer-
ence to the top surface of the MX-CF11.

1)

Remove the scanner lock screw (a) and the caution label (b).

1

Operation panel

1

2

Panel cover B

1

3

Panel cover below

1

4

Screw  3  x  6

6

5

Screw  4  x  8

8

6

Clamp

4

7

Panel support plate unit

1

8

Panel cover A

1

9

Height adjuster plate

4

10

Lower cover

1

Low

High

a

b

MX-M1204  MX-M904/M1054/M1204 (MAIN UNIT)  2 – 7

1)

Pull out trays 1 and 2, and remove the rotating plate lock screw
(a) and the tray caution label (b).

2)

Pull out trays 3 and 4, and remove the rotating plate fixing
material (a) and the tray caution label (b). Remove the blue
screw (c) from the tray 3 only. 

1)

Attach the document scan section label to the top of the DSPF
unit.

1)

Remove the operation panel upper cover with the screw.

2)

Attach the frame, and fix the screw. (Packed items No.5 x4).

3)

Attach the four clamps (Packed items No.6 x4) and arrange
the wires.

NOTE: When wiring the harness, be sure to check that the

cable is not in the hole. Remove slack from the har-
ness.

a

a

a

a

b

b

b

a

c

b

c

MX-M1204  MX-M904/M1054/M1204 (MAIN UNIT)  2 – 8

NOTE: Check to confirm that the harness does not enter the

panel. 
For the reference, refer to the figure below.

4)

Attach the operation panel to the machine with the screw.
(Packed items No.5 x4).

5)

Attach the panel cover A (Packed items No.8) with the screw.
(Packed items No.4 x2).

NOTE: At that time, pass the harness through the hole in the

cover. 

NOTE: Place the cover on the inside of plate.

6)

Bind up the harness with clamp as per the following picture.

NOTE: Be careful not to pinch the harness. If it is difficult to

connect the connector, remove the cabinet in the right
side.

7)

Pass the harness through the clamp and the wire saddle, and
connect the connector.

NOTE: Be careful not to pinch the lead wires.