Sharp MX-M850 (serv.man39) Service Manual ▷ View online
MX-M1100 MAINTENANCE 9 – 69
33) Check the horizontal transport clutch (a) of the tandem drive,
the vertical transport clutch (Upper) (b), the cassette 2 paper
transport clutch (c), the vertical transport clutch (Middle) (d),
and the cassette 1 paper transport clutch (e) at every 500K.
transport clutch (c), the vertical transport clutch (Middle) (d),
and the cassette 1 paper transport clutch (e) at every 500K.
34) Disconnect the connector (a), and remove the resin ring (b),
and replace the horizontal transport clutch (c), the vertical
transport clutch (Upper) (d), the cassette 2 paper transport
clutch (e), the Vertical transport clutch (Intermediate) (f).
* Set the clutch so that the bent section of the plate is
transport clutch (Upper) (d), the cassette 2 paper transport
clutch (e), the Vertical transport clutch (Intermediate) (f).
* Set the clutch so that the bent section of the plate is
engaged with the notch of the clutch.
35) Disconnect the connector (a), and remove the resin ring (b),
and replace the cassette 1 paper transport clutch (c).
* Set the clutch so that the bent section of the plate is
* Set the clutch so that the bent section of the plate is
engaged with the notch of the clutch.
36) Disconnect the connector (a), and remove the screw (b).
Remove the tandem drive unit (c).
37) Check the grease applying section (a) at every 500K. If neces-
sary, apply grease (HANARL) to the section.
38) Insert the stopper (a) into the shaft, rotate the screw (b) clock-
wise to remove it, and remove the coupling (c), the spring (d),
and the washer (e).
and the washer (e).
a
c
e
d
b
a
b
b
c
d
e
f
a
b
c
a
b
b
b
c
a
b
b
a
a
b
c
c
d
e
c
MX-M1100 MAINTENANCE 9 – 70
39) Remove the screw (a), and remove the plate (b).
40) Check the torque limiter (a) at every 500K.
41) Check the belt (a) at every 500K.
42) Remove the torque limiter unit (a).
43) Remove the bearing (a), the E-ring (b), the parallel pin (c), and
the gear (d). Remove the torque limiter (e), the resin part (f),
and the washer (g). Replace the torque limiter (e).
and the washer (g). Replace the torque limiter (e).
44) Disconnect the connector (a), and remove the screw (b).
Remove the multi-stage drive unit (c).
45) Check the grease applying section (a) at every 500K. If neces-
sary, apply grease to the section.
46) Disconnect the connector (a), and remove the screw (b).
Remove the multi-stage drive B unit (c).
a
a
a
a
b
a
a
a
a
b
d
c
c
e
f
g
b
a
b
b
c
a
a
b
b
c
MX-M1100 MAINTENANCE 9 – 71
47) Check the belt (a) at every 500K.
48) Remove the E-ring (a), the pulley (b), the belt (c), the parallel
pin (d), and the seat (e).
49) Remove the E-ring (a), the roller (b), the gear (c), and the par-
allel pin (d).
50) Remove the screw (a), and remove the plate (b).
51) Check the cassette 3 paper transport clutch (a), the cassette 4
paper transport clutch (b), and the Vertical transport clutch
(Lower) (c) at every 500K.
(Lower) (c) at every 500K.
52) Disconnect the connector (a). Remove the gear unit (b), and
remove the cassette 3 paper transport clutch unit (c).
a
a
a
b
c
a
e
d
a
d
b
c
a
d
b
c
a
a
a
a
b
b
b
a
c
a
b
c
MX-M1100 MAINTENANCE 9 – 72
53) Remove the bearing (a), the E-ring (b). Replace the cassette 3
paper transport clutch (c).
54) Disconnect the connector (a), and remove the cassette 4
paper transport clutch unit (b).
55) Remove the bearing (a), the E-ring (b), and replace the cas-
sette 4 paper transport clutch (c).
56) Disconnect the connector (a), and remove the Vertical trans-
port clutch (Lower) unit (b).
57) Remove the bearing (a), the E-ring (b), and replace the Verti-
cal transport clutch (Lower) (c).
a
c
b
a
b
a
b
c
a
b
a
b
c
Click on the first or last page to see other MX-M850 (serv.man39) service manuals if exist.