DOWNLOAD Sharp MX-M850 (serv.man37) Service Manual ↓ Size: 1.17 MB | Pages: 103 in PDF or view online for FREE

MX-M1100  SIMULATION  7 – 5

26

52

Used to set whether non-print paper (insertion, cover sheet) is counted or not.

Setting

69

Used to set preliminary preparation of toner and near end display when the toner quantity 
reaches 25%.

Setting

27

1

Used to set non-detection of the communication error (U7-00) with RIC.

Setting

2

Used to set the FSS function (user registration number, Host server telephone number).

Setting

4

Used to set the FSS function (initializing, call, toner order auto send).

Setting

5

Used to set the machine tag No. 
(This simulation allows to check the machine tag No. from the host computer side.)

Communication 
(RIC/MODEM)

Setting

6

Used to set the FSS function (manual service call).

Setting

7

Used to set the FSS function (enable, Alert calling)

Setting

9

Used to set the paper transport time between sensors and the gain adjustment retry number.

Setting

10

Used to clear the trouble prognosis history information.

Data clear

11

Used to check the serial communication retry number history and the scanner GAIN adjustment 
retry number history.

Other

12

Used to check the error history of high density, half-tone potential, and dark potential.

Other

13

Used to check the history of paper transport time between sensors.

Other

14

Used to set the FSS function connection mode. (Enable only for Disable to Enable)

Setting

30

1

Used to check the operation of the sensors and the detectors in other than the paper feed section 
and the control circuits.

Operation test/check

2

Used to check the operation of the sensors and the detectors in the paper feed section and the 
control circuits.

Operation test/check

10

Used to check the Main unit double feed detection sensor (Paper feed)

(Must not be used 
unless a special 
change is required.)

33

1

Used to check the operation of the sensors in the card reader and the control circuit.

Operation test/check

2

The card ID (IDM) information supporting the Felica card in the machine user registration 
information is deleted.

Data clear

40

2

Used to adjust the detection level of the manual paper feed tray paper width detector.

Paper feed

Adjustment/ Setting

7

Used to adjust the manual paper feed tray size width detection level.

Paper feed

Adjustment/ Setting

12

Used to adjust the tray 4 width detection level.

Paper feed

Adjustment/ Setting

41

1

Used to check the operation of the document size sensor and the control circuit.

Operation test/check

2

Used to adjust the document size sensor detection level.

Adjustment

3

Used to check the operation of the document size sensor and the control circuit.

Operation test/check

43

1

Used to set the fusing temperature of each paper mode.

Setting

31

Used to check the operation of the fusing web cleaning motor and the control circuit.

Operation test/check

32

Used to set the forcible operation of the fusing web cleaning when job end.

Adjustment/ Setting

33

Used to make setting of before-fusing PG operations. 

Setting

44

1

Used to set each correction function of the image forming (process) section.

Process (OPC 
drum, developing, 
transfer, cleaning)

Setting

2

Used to adjust the process control sensor gain.

Process

Adjustment/ Setting

3

A change in the OPC drum surface potential VO due to the OPC drum environment and 
membrane decrease (life) is detected with the surface potential sensor to correct the grid 
potential Vg so that the cleaning field is maintained at a constant level.

Process

Operation test/check

4

Used to set the operating conditions of the high density process control.

(Must not be used 
unless a special 
change is required.)

5

Used to set the dark potential adjustment conditions.

Adjustment/ Setting

6

Used to perform forcible execution of the high density process correction.

Adjustment

7

Used to clear the high density process control correction data.

Data clear

9

Used to display the process data.

Process (OPC 
drum, developing, 
transfer, cleaning)

(This simulation is 
normally not used in 
the market.)

12

Used to display the result of the high density process control.

Process (OPC 
drum, development)

(This simulation is 
normally not used in 
the market.)

14

Used to check the output levels of the fusing temperature sensor, the machine temperature 
sensor, and the humidity sensor.

Process (OPC 
drum, development)

Adjustment/ Setting/ 
Operation data check

16

Used to check the toner density control data.

(This simulation is 
normally not used in 
the market.)

28

Used to set the process control execution timing.

Adjustment/ Setting

33

Used to perform forcible execution of the half-tone potential adjustment.

Adjustment/ Setting

34

Used to correct the half tone potential changing caused by dark decrease variation made by 
membrane decrease (life) / temperature characteristics of the OPC drum.

35

Used to display the half-tone potential adjustment result.

36

Used to clear the half-tone potential adjustment correction quantity.

Data clear

46

2

Used to adjust the copy density adjustment in the copy mode.

Adjustment 
(B/W copy mode)

4

Used to adjust the density in the scanner mode.

Adjustment 
(Color scanner mode)

5

Used to adjust the density in the scanner mode.

Adjustment 
(Monochrome 
scanner mode)

MX-M1100  SIMULATION  7 – 6

46

8

Used to adjust the scanner color balance RGB.

Adjustment 
(Color scanner mode)

9

Used to adjust the copy density adjustment in the copy mode.

Adjust (DSPF mode)

10

Used to perform the engine gray balance manual adjustment.

Adjustment

16

Used to perform the engine color balance manual adjustment.(Monochrome, all modes)

Adjustment

19

Used to set the monochrome auto exposure mode.

Setting

23

Used to set the half-tone max. density correction.

Adjustment/ Setting

24

Used to adjust the engine half-tone auto density adjustment.

Adjustment

32

Adjustment of basic color density for AE mode

Adjustment/ Setting

37

Used to adjust B/W image forming.

Adjustment/ Setting

39

Used to adjust the image send sharpness.

Adjustment/ Setting

40

Used to collectively adjust all the FAX exposure modes.

Adjustment/ Setting

41

Used to adjust the FAX exposure (normal text).

Adjustment/ Setting

42

Used to adjust the FAX exposure (small text).

Adjustment/ Setting

43

Used to adjust the FAX exposure (fine).

Adjustment/ Setting

44

Used to adjust the FAX exposure (super fine).

Adjustment/ Setting

45

Used to adjust the FAX exposure (600 dpi)

Adjustment/ Setting

47

Used to set the JPEG compression rate in copying and scanning.

Adjustment/ Setting

48

1

Used to adjust the copy magnification ratio (main/sub scanning direction).

Adjustment

5

Used to adjust the copy magnification ratio (sub scanning direction).This adjustment is performed 
when Sim. 48-1 is used to adjust the sub scanning direction magnification ratio and a copy is 
made in a different copy magnification ratio and a satisfactory result is not obtained.

Scanner section

Adjustment

49

1

Firmware update

3

Used to update the instruction manual stored in the HDD.

50

1

Used to adjust copy image position on print paper and the void area (image loss) in the copy 
mode. (The similar adjustment can be performed with Sim. 50-5 and Sim. 50-2 (Simple method). 
(Document table mode))

Adjustment

2

Used to adjust the copy image position on the paper and the void area (image loss) in the copy 
mode. (This simulation, similar to Sim. 50-1, provides more simplified adjustment.)

Adjustment

5

Used to adjust the printer print lead edge.

Adjustment

6

DSPF document lead edge adjustment Used to adjust the copy image position on print paper 
and the void area (image loss) in the copy mode. (The similar adjustment can be performed with 
Sim. 50-7 (Simple method).) (DSPF mode)

DSPF Adjustment

7

DSPF document lead edge adjustment (Simple method) Used to adjust the copy image position 
on print paper and the void area (image loss) in the copy mode. (Sim. 50-6 simple method)

DSPF Adjustment

10

Used to adjust the print image off-center position. 
(The adjustment is made for each paper feed section.)

Adjustment

12

Used to adjust the scan image off-center position. (The adjustment is made for each scan mode.)

Adjustment

27

Used to adjust the image loss of a scan image in the FAX/ Scanner mode.

Adjustment

28

Used to perform the OC adjustment, the BK main scan magnification ratio correction, the DSPF 
adjustment, and the print position adjustment.

Adjustment

51

2

Used to adjust the contact pressure of paper against the resist roller (main unit paper feed, 
duplex paper feed, DSPF paper feed) in each section. (This adjustment is required when there is 
a great variation in the print image position for the paper or when paper jam occurred.)

Adjustment/ Setting

53

6

Used to adjust the DSPF width detection level.

Adjustment

7

Used to set the DSPF width adjustment value. (Sim. 53-6 manual input)

Adjustment/ Setting

8

Used to adjust the DSPF document scan start position.

Adjustment

12

Used to check the operations of the DSPF double feed sensor.

(Must not be used 
unless a special 
change is required.)

55

1

Used to set the specifications of the engine control operation.

(Must not be used 
unless a special 
change is required.)

2

Used to set the specifications of the scanner control operation.

(Must not be used 
unless a special 
change is required.)

3

Used to set the specifications of the controller operation.

(Must not be used 
unless a special 
change is required.)

10

Used to enter the special stamp text input.

Special stamp text 
setting

56

1

Used to transfer data (which is used in PWB repair).

Backup

2

Used to back up the data (including user authentication data and address book data) in the 
EEPROM, the SRAM, and the HDD on the main unit  to the USB memory and to transfer the 
data.

Backup

3

Used to back up the document filing data.

Backup

4

Used to back up the job log data.

Backup

60

1

Used to check the operations (read/ write) of the MFP control (SDRAM).

Operation test/check

2

Used to set the onboard SDRAM.

(This simulation is 
normally not used in 
the market.)

61

1

Used to check the polygon motor rotation and the BD signal detection.

Adjustment/ Setting

3

Used to set the laser power.

Adjustment/ Setting

MX-M1100  SIMULATION  7 – 7

62

1

Used to format the hard disk. (Except for the operation manual area.)

2

Used to check the read/write operation of the hard disk. (Partial section)

Operation test/check

3

Used to check the read/write operation of the hard disk. (All area)

Operation test/check

6

Used to perform the self diag of the hard disk.

Operation test/check

7

Used to print the self diag error log of the hard disk.

Operation test/check

8

Used to format the hard disk. (Except for the system area and the operation manual area.)

10

Used to delete the job log data.

Data clear

11

Used to delete the document filing data.

Data clear

12

Used to set YES/NO of auto format in hard disk trouble.

Setting

13

Used to format the hard disk.(Operation manual area only).

63

1

Used to check the result of the shading correction.

Adjustment/ Setting/ 
Operation data check

2

Used to execute shading forcibly.

Scanner

Adjustment/ Setting

3

Used to perform the gamma correction and density conversion for RGB data inputted from the 
CCD.  The gamma correction 1 of the SCAN ASIC and the set value of color correction are 
calculated and set from the specified image data.

Scanner

Adjustment/ Setting

4

The average value of the patch scan values for the RGB image data inputted from the CCD are 
calculated and displayed.

Scanner

Adjustment/ Setting

5

Used to reset the color balance of the scanner to the default.

Adjustment/ Setting

6

Used to set the auto adjustment pattern of the engine and color balance.

Adjustment/ Setting

7

Used to set the auto density of the engine auto adjustment scanner target value. (Service)

Adjustment/ Setting

8

Used to reset the engine auto adjustment scanner target value to the default value.

Adjustment/ Setting

64

2

Self print (B/W mode)

Operation test / check

3

Self print (B/W mode: high speed process)

Operation test/check

4

Used to make the self print of the printer.

Operation test/check

5

Printer self print (PCL)

Operation test/check

6

Printer self print (PS)

Operation test/check

65

1

Used to adjust the detection position of the touch panel (LCD display section).

Operation panel 
section

Adjustment

2

Used to check the result of the touch panel (LCD display section) detection position adjustment.

Operation panel 
section

Operation check/Test

5

Used to check the key input of the operation panel.

Operation panel 
section

Operation check/Test

66

1

Used to change and check the soft switch setting.

Setting

2

Used to clear the soft switch and set the default value.

FAX

Data clear

3

Used to check the operation (read/write) of the FAX PWB memory. 

FAX

Operation test, check

4

Used to check the output operation (MODEM operation) of data signal in each data output mode 
of FAX. Send level: MAX

FAX

Operation test, check

5

Used to check the output operation of data signal in each data output mode of FAX(MODEM 
operation). Send level: Soft switch setting

FAX

Operation test, check

6

Used to print the confidential pass code.

FAX

User data output, 
check

7

Used to output the image memory data (memory send and receive).* The confidential receive 
contents are also outputted.

FAX

User data output, 
check

8

Used to check the output operation (audio output IC operation check) of the various audio signals 
of FAX. Send level: MAX

FAX

Operation test, check

9

Used to check the output operation of various audio signals of FAX (audio output IC operation). 
Send level: Soft switch setting

FAX

Operation test, check

10

Used to clear all the data (memory receive and send) of the image memory.* The confidential 
receive data are cleared simultaneously.

FAX

Data clear

11

Used to check the output operation in the FAX G3 mode 300bps (MODEM operation). Send 
level: MAX

FAX

Operation test, check

12

Used to check the output operation (MODEM operation) in the FAX G3 mode 300bps. Send 
level: Set with the soft switch.

FAX

Operation test, check

13

Used to set the number for the FAX dial signal output test. (In the dial signal output test with 
Sim. 66-14 - 16, the dial number set with this simulation is outputted.)

FAX

Setting

14

Used to set the make time in the FAX pulse dial mode (10PPS) and to execute the dial signal 
output test. (The signal of the dial number set with Sim. 66-13 is outputted.)

FAX

Setting/Operation 
test, check

15

Used to set the make time in the FAX pulse dial mode (20PPS) and to execute the dial signal 
output test. (The signal of the dial number set with Sim. 66-13  is outputted.)

FAX

Setting/Operation 
test, check

16

Used to perform the dial signal (DTMF) output test in the FAX tone dial mode. (The signal of the 
dial number set with Sim. 66-13 is outputted.) The send level can be set to an optional level.

FAX

Setting/Operation 
test, check

17

Used to perform the dial signal (DTMF) output test in the FAX tone dial mode. Send level: MAX

FAX

Operation test, check

18

Used to perform the dial signal (DTMF) output test in the FAX tone dial mode. Send level: Set 
with the soft switch.

FAX

Operation test, check

21

Used to print information abut FAX (various registrations, communication management, file 
management, system errors, protocols).

FAX

Adjustment, setting, 
operation data check

22

Used to adjust the handset sound volume

Adjustment/ Setting

24

Used to clear the FAST memory data.

FAX

Clear

25

Used to register a FAX number for MODEM dial-in.

FAX

Setting

26

Used to register an external telephone number for MODEM dial-in.

FAX

Setting

MX-M1100  SIMULATION  7 – 8

66

29

Used to clear the data related to the address book (one-touch registration, FTP/ Desktop 
extension, group extension, program registration, interface memory box, meta data, Inbound 
Routing, Document Admin table).

Data clear

30

Used to check a change in the TEL/LIU status.

FAX

Operation test, check

31

Used to set the TEL/LIU output port.

FAX

Operation check

32

Used to check the received data (fixed data) from the line.

FAX

Operation test, check

33

Used to detect the line signals (BUSY TONE/CNG/CED/FNET/DTMF).

FAX

Operation test, check

34

Used to measure the communication time of the send test image data. 

FAX

Operation test, check

36

Used to perform the interface check between the MFP controller and the MDMC. 
(Data line or command line check)

FAX

Operation test, check

39

Used to set the destination.

FAX

Setting

42

Used to rewrite the power control program again to the FAX BOX.

FAX

Setting

43

Used to write the adjustment value of the power control program to the FAX BOX.

FAX

Setting

60

Used to register the ACR data.  When calling, the carrier prefix is added to the dial number to 
provide the auto select function of low-price line to the user. * To use this simulation, the FAX soft 
SW 24-4 and 24-5 must be set to [FUNCTION ON] and [Register Enable]. 

Adjustment/ Setting

67

24

Used to set for auto color calibration. For FIERY option support, Sim  is not displayed.

Adjustment/ Setting

25

Used to set the printer engine color balance manual correction. For FIERY option support, the 
Sim is not displayed.

Adjustment/ Setting

27

Used to register the scanner target value of the printer engine auto density adjustment. For 
FIERY option support, this Sim is not displayed.

Adjustment/ Setting

28

Used to reset the printer engine auto adjustment scanner target value to the default value.

Adjustment/ Setting

31

Used to clear the printer calibration value. For FIERY option support, the Sim is not displayed.

Data clear

32

Printer screen gamma table setting (300/600DPI). When supporting the FIERY option, Sim is not 
displayed.

Adjustment/ Setting

33

Used to perform the gamma correction of printer screens (for PCL). For FIERY option support, 
the Sim is not displayed.

Adjustment/ Setting

34

Used to set Enable/Disable of the printer half-tone max. density correction.

Adjustment/ Setting