Sharp MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man17) Service Manual ▷ View online
MX-M503N SIMULATION 5 – 10
3-3
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1)
1)
Select the item to be operation checked with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
<Inner finisher>
<Saddle stitch finisher>
<4K finisher is installed>
FSAD
Staple safety SW
FSHTD
Shutter open detection
FCD
Upper door open detection
FFDD
Front cover open detection
F24V
24V output interruption detection
FPSW1
PUSHSW1 detection
FPSW2
PUSHSW2 detection
FPSW3
PUSHSW3 detection
FAED21
Tray 2 area detection 1
FAED22
Tray 2 area detection 2
FAED23
Tray 2 area detection 3
FDSW1
DIPSW1 detection
FDSW2
DIPSW2 detection
FDSW3
DIPSW3 detection
FDSW4
DIPSW4 detection
FDSW5
DIPSW5 detection
FDSW6
DIPSW6 detection
FDSW7
DIPSW7 detection
FDSW8
DIPSW8 detection
FPE
Punch motor lock detection
FPUC
Punch unit connection detection
FPHPD
Punch HP detection
FPSHPD
Punch horizontal resist HP detection
FPFDD
Punch front door open detection
FPDD
Punch dust detection
FPUDSW
Punch upper cover open detection SW
FINRPS
Entry port reverse pass solenoid
FSLS
Paper surface detection solenoid
FPDS
Paddle solenoid
FBRS
Belt separation solenoid
FRM
Registration motor
FSWM
Oscillation motor
FAM
Bundle exit paper exit motor
FFJM
Alignment motor front
FRJM
Alignment motor rear
FSM
Staple shift motor
FFSM
Staple motor
FTLM
Tray lift motor
FFANM
Fan motor
FPNM
Punch motor
FPSM
Punch side resist motor
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
),16(1625&+(&.
3'33'
3'33'
3'&6
)33'
)3$3+6B)
)3$3+6B5
)$73'
)*+36
)'73'
)3/'
)33'
)63+6
)673'
)6056
)78/'
)7//'
)6/6
)736
)&'
)&'
)7/056
)6+6
)66+36
)6('
)66:
)&'
)666:
))/
)'5+6
)33'
)6$73'
)666:
)3++'
)6$3+6
)63*+6
)65+6
)3''
)66+6
)66(6
)66&6
)666+6
PDPGS
FINRPS
Paper pass paper gate solenoid
PDPTM
FJPM
Paper pass paper transport motor
PDCF
FJFM
Paper pass cooling fan
FPTM1
FFM
Paper transport motor 1
FDRLM
FNM
Finisher paper exit roller lift motor
FGM
FGM
Gripper motor
FPAM-F
FFJM
Paper alignment motor F
FPAM-R
FRJM
Paper alignment motor R
FSSM
FSM
Stapler shift motor
FSM
FFSM
Staple motor
FPTM2
FLM
Paper transport motor 2
FSDM
FFM2
Saddle motor
FSPTM
FTM
Saddle paper transport motor
FSPAM
FSR3M
Saddle paper alignment motor
FSPM
FSJM
Saddle positioning motor
FSDSM
FPPM
Saddle staple motor
FPHS1
FSSM
Paper holding solenoid 1
FPHS2
FPHS
Paper holding solenoid 2
FTLM
FPS
Tray lift motor
FPM
FPNM
Punch motor
FPSM
FPSM
Punch shift motor
FINRPS
Interface paper gate solenoid
FJPM
Interface transport motor
FJFM
Interface transport fan motor
FFM
Entry port transport motor
FAM
Bundle paper exit motor
FFJM
Alignment motor front
FRJM
Alignment motor rear
FSM
Staple shift motor
FTLM1
Tray 1 lift motor
FTLM2
Tray 2 lift motor
FFSM
Staple motor
FSWM
Oscillation motor
FASM
Rear edge assist motor
FINRRS
Inlet port roller separation solenoid
FBRRS
Buffer roller separation solenoid
FFDRRS
Paper exit roller separation solenoid
FBES
Buffer rear edge holding solenoid
FSHC
Shutter open/close clutch
FAORC
Bundle exit lower roller clutch
FPNM
Punch motor
FPSM
Punch horizontal resist motor
㩷
㩷
㩷
㩷
㩷
㩷
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
),1/2$'&+(&.
(;(&87(
3'3*6
3'370
)370
3'&)
)'5/0
)*0
)3$05
)3$0)
)660
)60
)370
)7/0
)6'0
)6370
)630
)63$0
)6'60
)3+6
)3+6
MX-M503N SIMULATION 5 – 11
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Operation/Procedure
1)
1)
Select an adjustment target item with [
] [] key on the touch
panel.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
<Inner finisher>
<Saddle stitch finisher>
NOTE: "A: SADDLE POSITION (Saddle binding position adjust-
ment)" and "B: FOLDING POSITION (Saddle folding posi-
tion adjustment"
The saddle binding position adjustment and the saddle
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting
tion adjustment"
The saddle binding position adjustment and the saddle
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting
5.0mm)
In general, when the saddle binding position and the sad-
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.
<4K finisher>
4
4-2
Purpose
Operation test/check
Function (Purpose) Used to check the paper feed section
(Desk/LCC) sensors and detectors and
their control circuits.
their control circuits.
Section
Paper feed, paper reverse/transport
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
Item/Display
Content
Setting
range
Default
value
A
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
2 - 18
10
B
REAR ADJUST
Alignment position
adjustment (rear)
adjustment (rear)
2 - 18
10
C
STAPLE REAR
Staple binding position
adjustment
(one position at the rear)
adjustment
(one position at the rear)
68 - 132
100
D
STAPLE
FRONT
FRONT
Staple binding position
adjustment
(one position in front)
adjustment
(one position in front)
68 - 132
100
E
STAPLE BOTH
Staple binding position
adjustment (center position
of two positions binding)
adjustment (center position
of two positions binding)
68 - 132
100
F
STAPLE PITCH
Staple binding position
adjustment (staple pitch of
two positions binding)
adjustment (staple pitch of
two positions binding)
68 - 132
100
G
PUNCH
CENTER
CENTER
Punch center positioning
sensor
sensor
37 - 63
50
H
PUNCH HOLE
Punch hole adjustment
(paper transport direction)
(paper transport direction)
42 - 58
50
Item/Display
Content
Setting
range
Default
value
A
SADDLE
POSITION
POSITION
Saddle stitch position
adjustment
adjustment
25 - 75
50
B
FOLDING
POSITION
POSITION
Saddle folding position
adjustment
adjustment
25 - 75
50
C
FRONT
ADJUST
ADJUST
Paper alignment position
adjustment (Front)
adjustment (Front)
35 - 65
50
D
REAR ADJUST
Paper alignment position
adjustment (Rear)
adjustment (Rear)
35 - 65
50
E
STAPLE REAR
Staple binding position
adjustment (one position at
the rear) (When the paper
width is greater than
232mm)
adjustment (one position at
the rear) (When the paper
width is greater than
232mm)
25 - 75
50
F
STAPLE REAR
R
R
Staple binding position
adjustment (one position at
the rear) (When the paper
width is 232mm or less)
adjustment (one position at
the rear) (When the paper
width is 232mm or less)
45 - 75
50
G
STAPLE
FRONT
FRONT
Staple binding position
adjustment (one position in
front) (When the paper
width is greater than
232mm)
adjustment (one position in
front) (When the paper
width is greater than
232mm)
25 - 75
50
H
STAPLE
FRONT R
FRONT R
Staple binding position
adjustment (one position in
front) (When the paper
width is 232mm or less)
adjustment (one position in
front) (When the paper
width is 232mm or less)
25 - 55
50
I
STAPLE BOTH
Staple binding position
adjustment (two positions
at the center)
adjustment (two positions
at the center)
45 - 55
50
J
STAPLE PITCH
Staple binding position
adjustment (two positions
in pitch)
adjustment (two positions
in pitch)
35 - 62
50
K
PUNCH
CENTER
CENTER
Punch center adjustment
35 - 65
50
L
PUNCH HOLE
Punch hole position
adjustment
adjustment
30 - 60
50
M
SADDLE_ADJU
ST_POS
ST_POS
Saddle alignment position
adjustment
adjustment
35 - 65
50
N
GRIPPER_POS
Gripper exit position
adjustment
adjustment
35 - 65
50
Item
Display
Item
Set range
Default
value
A
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
B
STAPLE REAR
Staple binding position
adjustment (one
position at the rear)
adjustment (one
position at the rear)
94 - 106
100
C
STAPLE FRONT
Staple binding position
adjustment (one
position in front)
adjustment (one
position in front)
94 - 106
100
D
PUNCH
CENTER
CENTER
Punch center
adjustment
adjustment
30 - 70
50
E
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 - 52
50
Item/Display
Content
Setting
range
Default
value
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
),1,6+(5$'-8670(17
$˖
˷̚˹
˖6$''/(326,7,21
$˖
˖)2/',1*326,7,21
%˖
˖)5217$'-867
&˖
˖5($5$'-867
'˖
˖67$3/(5($55
)˖
˖67$3/(5($5
(˖
˖67$3/()5217
*˖
˖67$3/()52175
+˖
˖67$3/(%27+
,˖
˖67$3/(3,7&+
-˖
˖381&+&(17(5
.˖
˖381&++2/(
/˖
2.
MX-M503N SIMULATION 5 – 12
<Desk>
<A4 LCC>
4-3
Purpose
Operation test/check
Function (Purpose) Used to check the paper feed section
(Desk/LCC) loads and their control circuits.
Section
Paper feed, paper reverse/transport
Operation/Procedure
1)
1)
Select the load item that is required to operation check with the
touch panel key.
touch panel key.
2)
Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
<Desk>
<A4 LCC>
4-5
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the paper
transport clutch for the paper feed tray unit.
Section
Paper feed, paper reverse/transport
Operation/Procedure
[Check the ON operation]
Press the clutch button of the target of the ON operation check.
Checking is started. When the operation is normal, the button on
the display is highlighted. When it is abnormal, the button is not
highlighted.
[Check the OFF operation]
Press the highlighted button which is ON.
When the operation is normal, the highlighted button on the display
returns to the normal display. When it is abnormal, the highlighted
display is maintained.
[Check the ON operation]
Press the clutch button of the target of the ON operation check.
Checking is started. When the operation is normal, the button on
the display is highlighted. When it is abnormal, the button is not
highlighted.
[Check the OFF operation]
Press the highlighted button which is ON.
When the operation is normal, the highlighted button on the display
returns to the normal display. When it is abnormal, the highlighted
display is maintained.
DCSI1
Desk 1 installation detection
DPFD1
Desk 1 transport detection
DLUD1
Desk 1 upper limit detection
DPED1
Desk 1 paper empty detection
DCSPD1
Desk 1 remaining paper quantity detection
DCSS11
Desk 1 rear edge detection 1
DCSS12
Desk 1 rear edge detection 2
DCSS13
Desk 1 rear edge detection 3
DCSS14
Desk 1 rear edge detection 4
DCSI2
Desk 2 installation detection
DPFD2
Desk 2 transport detection
DLUD2
Desk 2 upper limit detection
DPED2
Desk 2 paper empty detection
DCSPD2
Desk 2 remaining paper quantity detection
DCSS21
Desk 2 rear edge detection 1
DCSS22
Desk 2 rear edge detection 2
DCSS23
Desk 2 rear edge detection 3
DCSS24
Desk 2 rear edge detection 4
DSW_DSK
Desk transport cover open/close detection
LPFD
LCC transport sensor
LUD
LCC tray upper limit sensor
LDD
LCC tray lower limit sensor
LPED
LCC tray paper empty sensor
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder sensor
L24VM
LCC24V power monitor
LLSW
LCC upper limit SW
LTOD
LCC main unit connection detection
DPFM
Desk main motor
DLUM1
Desk 1 lift-up motor
DPUC1
Desk 1 paper feed clutch
DLUM2
Desk 2 lift-up motor
DPUC2
Desk 2 paper feed clutch
DTRC
Desk transport clutch
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'6./&&6(1625&+(&.
'&6,
'3)'
'/8'
'3('
'&63'
'&66
'&66
'&66
'&66
'&6,
'3)'
'/8'
'3('
'&63'
'&66
'&66
'&66
'&66
'6:B'6.
LPFM
LCC transport motor
LLM
LCC lift motor
LPFC
LCC paper feed clutch
LPFS
LCC paper feed solenoid
LTRC
LCC transport clutch
button
Content
DTRC
Desk transport clutch
LTRC
LCC transport clutch
㩷
㩷
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'6./&&/2$'&+(&.
(;(&87(
'3)0
'/80
'/80
'38&
'38&
'75&
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'(6./&&6<1&521,=,1*6,*1$/&+(&.
/75&
˖/75&2))
'75&
˖'75&2))
MX-M503N SIMULATION 5 – 13
5
5-1
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the display,
LCD in the operation panel, and control cir-
cuit.
cuit.
Section
Operation unit
(Operation/Display Control PWB)
(Operation/Display Control PWB)
Operation/Procedure
The LCD is changed as shown below.
The contrast changes every 2sec from the current level to MAX
The LCD is changed as shown below.
The contrast changes every 2sec from the current level to MAX
MIN
the current level. During this period, each LED is lighted.
The LCD display contrast change and the LED lighting status are
checked.
checked.
5-2
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the heater
lamp and the control circuit.
Section
Fusing
Operation/Procedure
1)
1)
Select the item to be operation checked with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The selected heater lamp repeats ON/OFF operations 10
times at the interval of 500ms.
When [EXECUTE] key is pressed, the operation is terminated.
The selected heater lamp repeats ON/OFF operations 10
times at the interval of 500ms.
When [EXECUTE] key is pressed, the operation is terminated.
Heater lamp operation check method:
Remove the rear cabinet, open the PWB holder, and the heater
lamp lighting status can be checked from the clearance between
the frames.
Remove the rear cabinet, open the PWB holder, and the heater
lamp lighting status can be checked from the clearance between
the frames.
5-3
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the scanner
lamp and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1)
1)
Select the item to be operation checked with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The scanner lamp lights up for 10 sec.
When [EXECUTE] key is pressed, the operation is terminated.
The scanner lamp lights up for 10 sec.
When [EXECUTE] key is pressed, the operation is terminated.
[DSPF-installed model]
[RSPF-installed model]
HL_UM
Main heater lamp (HL MAIN)
HL_US
Sub heater lamp (HL SUB)
HL_UW
Warm-up heater lamp (HL UW)
ǂǂǂSIMULATION
ǂǂNO.05-01
7(67
ǂǂǂ6,08/$7,21ǂǂ12
7(67
Display
Content
OC COPY LAMP
OC scanner lamp
DSPF COPY LAMP
DSPF scanner lamp (DSPF-installed model only)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
+($7(5/$03/2$'6(783
+/B80
+/B86
+/B8:
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
&23</$03&+(&.
2&&23</$03
(;(&87(
'63)&23</$03
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
&23</$03&+(&.
2&&23</$03
(;(&87(
Click on the first or last page to see other MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man17) service manuals if exist.