Sharp MX-M310 / MX-M310N (serv.man3) Service Manual ▷ View online
MX-M260/M310/M260N/M310N SIMULATION 6 - 12
Operation/procedure
Enter the set value with the 10-key.
When the duplex motor setting is made, the duplex 2motor is also set
accordingly.
accordingly.
Operation/procedure
1.
Touch the item to set.
2.
Enter the set value with the 10-key, and press the [START] key.
Operation/procedure
Press the [START] key and operate the toner motor for 30 sec.
Operation/procedure
1.
Press the [START] key.
2.
When “1: YES” is selected, troubles other than U2 and PF are can-
celed. (When “2: NO” is selected, the simulation is canceled.)
celed. (When “2: NO” is selected, the simulation is canceled.)
Operation/procedure
1.
Press the [START] key.
2.
When “1: YES” is selected, U2 trouble is canceled.
(When “2: NO” is selected, the simulation is canceled.)
(When “2: NO” is selected, the simulation is canceled.)
Operation/Procedure
1.
Press the [START] key.
2.
When “1: YES” is selected, PF trouble is canceled. (When “2: NO”
is selected, the simulation is canceled.)
is selected, the simulation is canceled.)
Operation/procedure
1.
Enter the set value with the 10-key.
2.
Press the [START] key.
* When selecting 150K, maintenance message is displayed by imple-
menting the following conditions.
• Maintenance count = 150K.
• DV count = 100K
• DR count = 100K
* When maintenance message is displayed, replace consumption part
reaching the number of sheets of maintenance, then clear the
replaced part's counter only.
replaced part's counter only.
9-4
Purpose
Operation test/check
Function (Purpose)
Duplex motor RPM setting
Section
Duplex
Item
Operation
Setting range
1-13
Default
5
9-5
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the timing of switching from normal
rotation to reverse rotation or from reverse rotation to
normal rotation of the duplex motor.
rotation to reverse rotation or from reverse rotation to
normal rotation of the duplex motor.
Item
Installation range
Default
1
145mm/s
18-76
18
2
122mm/s
18
3
RIGHT 145mm/s
50
4
RIGHT 122mm/s
50
10
10-0
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the toner motor and its
control circuit.
control circuit.
Section
Image process
(Photoconductor/Developing/Transfer/Cleaning)
Developer/Toner hopper
(Photoconductor/Developing/Transfer/Cleaning)
Developer/Toner hopper
Item
Operation
14
14-0
Purpose
Clear/Cancel (Trouble etc.)
Function
(Purpose)
(Purpose)
Used to cancel excluding the self-diag U2/PF troubles.
Item
Trouble
Error
16
16-0
Purpose
Clear/Cancel (Trouble etc.)
Function (Purpose)
Used to cancel the self-diag U2 trouble.
Item
Trouble
Error
17
17-0
Purpose
Cancel (Trouble, etc)
Function (Purpose)
Used to cancel the self diag “PF” trouble.
Item
Trouble
Error
21
21-1
Purpose
Setting
Function (Purpose)
Used to set the maintenance cycle.
Item
Specifications
Counter
Item
Content
26cpm
31cpm
0
5K
5K
1
10K
10K
2
20K
50K
3
25K
75K
4
50K
100K
5
75K (Default)
150K (Default) *
6
FREE
FREE
MX-M260/M310/M260N/M310N SIMULATION 6 - 13
Operation/procedure
Each counter is displayed.
Operation/procedure
Each counter data are displayed.
The counter display is in 7 digits.
Operation/procedure
The misfeed history is displayed in the sequence of recentness by the
name of sensors and detectors. Max. 40 items of information can be
stored in memory. (The old ones are deleted sequentially.) The trouble
section may be determined by the data.
name of sensors and detectors. Max. 40 items of information can be
stored in memory. (The old ones are deleted sequentially.) The trouble
section may be determined by the data.
(Jam cause code)
Operation/procedure
The trouble error codes are displayed in the sequence of the latest one
first. Max. 40 items of information are stored. (Older ones are deleted
in sequence.) The machine condition can be estimated by this data.
first. Max. 40 items of information are stored. (Older ones are deleted
in sequence.) The machine condition can be estimated by this data.
Operation/procedure
Used to display the ROM version of each section.
[Display example]
ROM version 1.250
→
[1.25] (up to 2 decimal places)
The display of the protocol monitor and the soft SW follows this display.
If it is not installed, “- - - - - - - - - -” is displayed.
22
22-1
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the counter value of each section.
Item
Counter
TOTAL
Total counter
MAINTENANCE
Maintenance counter
DEVE
Developer counter
DRUM
Drum counter
COPY
Copy counter
PRINTER
Printer counter
IMC
IMC counter
DUPLEX
Duplex counter
OTHERS
The other counters
FAX SEND
FAX Send counter
FAX RCV
FAX receive counter
FAX OUTPUT
FAX print counter
DEVE RANGE
Developer traveling distance counter
DRUM RANGE
Drum traveling distance counter
DEVE ROLL
Developer rotation counter (K)
DRUM ROLL
Drum rotation counter (K)
DEVE LIFE
Developer life meter (%)
DRUM LIFE
Drum life meter (%)
22-2
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the total numbers of misfeed and
troubles. (When the number of misfeed is considerably
great, it is judged as necessary for repair. The misfeed
rate is obtained by dividing this count value with the
total counter value.)
troubles. (When the number of misfeed is considerably
great, it is judged as necessary for repair. The misfeed
rate is obtained by dividing this count value with the
total counter value.)
Item
Trouble
PAPER JAM
JAM counter
SPF JAM
RSPF JAM counter
TROUBLE
Trouble counter
22-3
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the misfeed positions and the number of
misfeed at each position. (When the number of
misfeed is considerably great, it can be judged as
necessary for repair.)
misfeed at each position. (When the number of
misfeed is considerably great, it can be judged as
necessary for repair.)
Item
Trouble
Mis-feed
Item
Jam contents
TRAY1
1st tray pick-up miss
TRAY2
2nd tray pick-up miss
TRAY3
3rd tray pick-up miss
TRAY4
4th tray pick-up miss
BPT
Multi manual feed pick-up miss
PPD1_ND
Paper-in sensor lead edge jam
PPD1_ST
Paper-in sensor rear edge jam
PPD1_DUP
Paper-in sensor reverse jam
PPD2_ND
Duplex sensor lead edge jam
PPD2_ST
Duplex sensor rear edge jam
POD2_ND
Upper tray paper exit lead edge jam
POD2_ST
Upper tray paper exit rear edge jam
POD1_ND
Lower tray paper exit lead edge jam
POD1_ST
Lower tray paper exit rear edge jam
PINT_SHORT
Abnormality between PS papers.
PFD2_ND
2nd paper pass lead edge jam
PFD2_ST
2nd paper pass rear edge jam
PFD3_ND
3rd paper pass lead edge jam
PFD3_ST
3rd paper pass rear edge jam
PFD4_ND
4th paper pass lead edge jam
PFD4_ST
4th paper pass rear edge jam
SIZE_SHORT
Duplex short scale error
FPPD1_N
Finisher entry port sensor not-reached jam
FPPD1_S
Finisher entry port sensor remaining jam
FSTPD_S
Finisher paper exit remaining jam
FSTPLJ
Finisher staple jam
22-4
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the total trouble (self diag) history.
Item
Trouble
22-5
Purpose
Adjustment/Setting/Check
Function
(Purpose)
(Purpose)
Used to check the ROM version of each unit (section).
Item
Software
S/N
Machine serial number
MCU
Main Control Unit
IMC
IMC
OPE
Panel + Panel label code
PRINTER
PRINTER
NIC
NIC
FINISHER
FINISHER
FAX
FAX
PUNCH
UNIT
UNIT
Punch unit
Panel
display
Destination
Panel software support language
JPN
Japan
Japanese, American English, English
Item
Jam contents
MX-M260/M310/M260N/M310N SIMULATION 6 - 14
Operation/Procedure
(Initial screen)
The currently set value is highlighted beside the adjustment item.
1.
Select the adjustment item with the 10-key.
2.
Press the [START] key.
The display is shifted to the copy menu and the set value is stored.
The display is shifted to the copy menu and the set value is stored.
3.
Select the paper feed tray and the print density.
4.
Press the [START] key.
Copying is started. (Printing at 1200dpi cannot be made.)
Copying is started. (Printing at 1200dpi cannot be made.)
After canceling a jam (After picking up, the [C] key is invalid.)
When the other information is repeatedly printed, the display may show
the message, “Remove original from original table.” However, the oper-
ation is performed normally.
the message, “Remove original from original table.” However, the oper-
ation is performed normally.
* When the IMC board is not installed, key input is disabled.
* Duplex print cannot be made.
* For the FAX SIM setting list, the display and the operating proce-
dures differ.
Note: When the simulation is canceled, the display returns to the origi-
nal state but the machine is not reset.
Operation/procedure
Used to display the administrator password.
Operation/procedure
Each counter is displayed.
The counter display is in 7 digits.
Operation/procedure
Used to display each paper feed counter.
The counter display is in 7 digits.
Operation/procedure
The detected machine composition is displayed.
(The job separator cannot be detected. Based on SIM 26-1 setting.)
(The job separator cannot be detected. Based on SIM 26-1 setting.)
EFS
SEC
American English, English, French, Spanish,
Brazilian Portuguese
Brazilian Portuguese
SECL
SUK
SCA/SCNZ
Distributor
area
area
EEU
SEEG/
SEA/East
Europe,
etc.
SEA/East
Europe,
etc.
English, German, Polish, Czech, Hungarian,
Greek, Turkish, Russian, French, Italian,
Slovak
Greek, Turkish, Russian, French, Italian,
Slovak
NEU
SEF/
SEES/
SEIS/SEN,
etc.
SEES/
SEIS/SEN,
etc.
English, German, French, Spanish, Dutch,
Italian, Portuguese, Swedish, Norwegian,
Finnish, Danish
Italian, Portuguese, Swedish, Norwegian,
Finnish, Danish
CHN
SOCC
Simplified Chinese, American English,
English
English
TWN
Taiwan
Traditional Chinese (Local support),
American English, English
American English, English
ARB
Saudi
Arabia
Arabia
American English, English, French, Spanish,
Hebrew
Hebrew
(Local support), Arabic
FAS
Iran
English, Arabic, Persian
22-6
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to print each key operator setting, the account
information, and the machine adjustment values.
information, and the machine adjustment values.
Item
Data
Setting/adjustment data
Item
Content
1
ALL
All lists group print (Default)
2
KEY OPE
Key operator information list
3
ACCOUNTING
COUNTERS
COUNTERS
List of total number of prints
4
AUDITOR NO.
Department number list
5
MACHINE SIM
SETTING
SETTING
Machine simulation setting list
6
FAX SIM SETTING*1
FAX simulation setting list (Only when
the FAX board is installed. The display
does not go to the print data transfer
display, but to the FAX SIM menu.)
the FAX board is installed. The display
does not go to the print data transfer
display, but to the FAX SIM menu.)
Panel
display
Destination
Panel software support language
22-7
Purpose
User data output/Check (Display/Print)
Function
(Purpose)
(Purpose)
Used to display of the administrator password.
Item
Data
User data
22-8
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to display the original, staple counter.
Item
Counter
SPF
RSPF counter
SCAN
Scan counter
STAPLE
Stapler counter
22-9
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the number of use of each paper feed
section. (the number of prints)
section. (the number of prints)
Section
Paper feed
Item
Counter
BYPASS
Manual feed counter
TRAY1
Tray 1 counter
TRAY2
Tray 2 counter
TRAY3
Tray 3 counter
TRAY4
Tray 4 counter
22-10
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the system configulation.
Item
Specifications
Option
Item
Display items
SPEED
26CPM/31CPM
DF
NONE/[1: RSPF]
OUTPUT
NONE/[2: Finisher]/[3: Job separator]
CASETTE1
NONE/[4: One-step paper feed unit]
CASETTE2
NONE/[5: Two-step paper feed unit]
IMC MEM
NONE/Expansion memory capacity (MB)
PRINTER
NONE/[6: PRINTER]
PS3
NONE/[7: PS3]
NIC
NONE/[8: NIC]
SCANNER
NONE/[9: SCANNER]
FAX
NONE/[10: FAX]
FAX MEM
NONE/Memory capacity (MB)
HAND SET
NONE/[11: Handset]
USB HOST
NONE/USB HOST
MX-M260/M310/M260N/M310N SIMULATION 6 - 15
NONE: When it is not installed, “- - - - - - - - - -” is displayed.
[ ]: Shows the product code in the list below.
*1: The number of installed units is displayed beside the model code.
For the tray, only the option tray is displayed.
Operation/procedure
Used to display the FAX send/receive counter.
The counter display is in 8 digits.
Note: Executable only when the FAX is installed.
Operation/procedure
Used to display the RSPF jam history data sequentially from the latest
one.
one.
Forty RSPF jam histories are displayed sequentially from the latest.
Operation/Procedure
Used to display the CRUM type.
Operation/procedure
Used to display the scanner counter.
The counter display is in 7 digits.
Operation/procedure
Jam/trouble counter is cleared individually. (The history of each
counter is deleted when clearing)
counter is deleted when clearing)
1.
Select the counter to be cleared with the 10-key.
2.
Press the [START] key.
The confirmation menu is shown.
The confirmation menu is shown.
3.
Select “1: YES.”
1: YES (Cleared)
2: NO (Not cleared) (Default)
2: NO (Not cleared) (Default)
ICCARDR/W
NONE/MX-ECX2
No.
Item
Model code
1
RSPF
MX-RP10
2
Finisher
MX-FN13
3
Job separator
MX-TR11
4
1 tray paper feed unit
MX-DE10 (*1)
5
2 tray paper feed unit
MX-DE11 (*1)
6
PRINTER
MX-PB12
7
PS3
MX-PK10
8
NIC
STANDARD (Only SoftNic)
9
SCANNER
MX-NSX1
10
FAX
AR-FX7
11
Handset
AR-HN4
22-11
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to display the FAX send/receive counter
(FAX reception and print counter).
(FAX reception and print counter).
Section
FAX
Item
Counter
FAX SEND PAGE/TIME
FAX send page and time
FAX RECEIVE PAGE/TIME
FAX receive page and time
FAX OUTPUT
FAX output (number of print)
22-12
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to check the misfeed positions and the number of
misfeed at each position.
(When the number of misfeed is considerably great, it
can be judged as necessary for repair.)
misfeed at each position.
(When the number of misfeed is considerably great, it
can be judged as necessary for repair.)
Section
RSPF
Item
Trouble
Misfeed
Error code
Name
Sensor name
Paper Reached/
Not Reached to
the sensor
DFD_ND
RSPF paper in lead
edge jam
edge jam
SPF P-IN
sensor
sensor
Not Reached
DFD_ST
RSPF paper in rear
edge jam
edge jam
SPF P-IN
sensor
sensor
Reached
RDD_ND
RSPF paper out
lead edge jam
lead edge jam
SPF P-IN
sensor
sensor
Reached,
P_OUT Not
Reached
P_OUT Not
Reached
RDD_ST
RSPF paper out
rear edge jam
rear edge jam
SPF P-OUT
sensor
sensor
Reached, P_IN
passed (OFF)
passed (OFF)
JAM_REV
RSPF duplex
reverse jam
reverse jam
SPF P-IN
sensor
sensor
Not Reached
(Paper after
reversing)
(Paper after
reversing)
ORG_SHORT
RSPF short size
error
error
SPF P-IN
sensor
sensor
Passed (OFF at
JAM)
JAM)
Item
Display items
ORG_LONG
RSPF long size
error
error
SPF P-OUT
sensor
sensor
Reached
SPF P-IN
sensor
sensor
Reached
22-13
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to display the CRUM type.
Item
Specifications
Item
Content
00
Not fixed.
01
AR-A
02
AR-B
03
AR-C
04
China
05
Japan
99
Conversion completed.
22-19
Purpose
Adjustment/setting/operation data output/check
(display/print)
(display/print)
Function
(Purpose)
(Purpose)
Used to display the scanner counter in the network
scanner mode.
scanner mode.
Section
Network scanner
Item
Counter
SCANMODE
Scanner mode counter
24
24-1
Purpose
Data clear
Function
(Purpose)
(Purpose)
Used to clear the misfeed counter, the misfeed history,
the trouble counter, and the trouble history. (The
counters are cleared after completion of maintenance.)
the trouble counter, and the trouble history. (The
counters are cleared after completion of maintenance.)
Section
Memory
Item
Counter
Item
Content
1
JAM
JAM counter/JAM history
2
SPF JAM
RSPF JAM counter/RSPF JAM history
3
TROUBLE
Trouble counter/Trouble history
Error code
Name
Sensor name
Paper Reached/
Not Reached to
the sensor
Click on the first or last page to see other MX-M310 / MX-M310N (serv.man3) service manuals if exist.