Sharp MX-GB50A (serv.man4) Service Manual ▷ View online
Sharp SmartPunch Pro Installation Manual
5
4. Installing the Sound Deadening Foam
Supplied with the SmartPunch Pro, you will find six
strips of sound deadening foam are shipped loose
for field installation. These are not attached at the
factory to avoid compression and/or damage
during shipping.
strips of sound deadening foam are shipped loose
for field installation. These are not attached at the
factory to avoid compression and/or damage
during shipping.
To install, simply peal the back off to reveal the
adhesive using the following steps as a reference.
adhesive using the following steps as a reference.
4.1
Paper Exit Side (Finisher Side)
Apply the wide strip to the right side as
shown.
shown.
Apply one of the two shorter pieces to the
side of the top cover as shown.
side of the top cover as shown.
GBC will update these
pictures to show the new
Sound foams for SmartPunch
Pro
pictures to show the new
Sound foams for SmartPunch
Pro
Sharp SmartPunch Pro Installation Manual
6
Apply one of the three longer strips to the left
rear panel as shown.
rear panel as shown.
Exit side complete
4.2 Paper Entrance Side (Printer Side)
Apply one of the two remaining long strips to the
right side of the printer side of the SmartPunch
Proas shown.
right side of the printer side of the SmartPunch
Proas shown.
Apply the last remaining short strip to the top
cover edge of the printer side of the SmartPunch
Pro as shown.
cover edge of the printer side of the SmartPunch
Pro as shown.
Apply the last remaining long strip to the left side
of the printer side of the SmartPunch Pro as
shown.
of the printer side of the SmartPunch Pro as
shown.
GBC will update these
pictures to show the new
Sound foams for SmartPunch
Pro
pictures to show the new
Sound foams for SmartPunch
Pro
Sharp SmartPunch Pro Installation Manual
7
5. Docking Bracket Installation
MX-ST10 High Capacity Stacker
The docking brackets are shipped in a
separate bag along with size M4
mounting screws (not shown).
separate bag along with size M4
mounting screws (not shown).
MX-RB18 Curl Correction Unit
MX-CF11 Inserter
Install as shown with the bracket
marked “R” on the right side facing
you as you look at the exit side of the
upstream device (pictures shown).
Install the bracket marked “L” on the
left side facing you. Both brackets
should be oriented with the arrow
facing up.
marked “R” on the right side facing
you as you look at the exit side of the
upstream device (pictures shown).
Install the bracket marked “L” on the
left side facing you. Both brackets
should be oriented with the arrow
facing up.
The docking bracket(s) provided with the
finisher should be attached to the
downstream side of the SmartPunch Pro
with 4 size M4 screws.
finisher should be attached to the
downstream side of the SmartPunch Pro
with 4 size M4 screws.
Sharp SmartPunch Pro Installation Manual
8
6. Leveling & Height Adjustment
6.1 Height Setting
No height adjustment of the SmartPunch Pro is required, for an installation site with a level floor. If the
floor is uneven then it is recommended to set the level of the SmartPunch Pro using the downstream
device as a reference.
6.2 Adjusting the Casters
floor is uneven then it is recommended to set the level of the SmartPunch Pro using the downstream
device as a reference.
6.2 Adjusting the Casters
a)
Using a 9/16” (15mm) open ended wrench, loosen
the jam nut(s) situated on the caster stud inside of
the machine
the jam nut(s) situated on the caster stud inside of
the machine
.
b)
Using the 9/16” (15mm) wrench, rotate the caster
stems to change the height.
Re-tighten the jam nuts once the correct height is
achieved.
stems to change the height.
Re-tighten the jam nuts once the correct height is
achieved.
Click on the first or last page to see other MX-GB50A (serv.man4) service manuals if exist.