Sharp MX-FX10 Service Manual ▷ View online
MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-51
131 1-2 Limitation of number
of times of PPR
when image is
continuousness non
detection
when image is
continuousness non
detection
Binary input
10 times
3-8 Not used
132 1-8 Not used
133
1
Not used
2
Manual calibration
when receiving
when receiving
Not executes manual
calibration when receiving
calibration when receiving
3-8 Not used
134
1
Summer time
Used to set whether the summer time is automatically set or not.
Disable: Other than the
below destinations
below destinations
Enable: U.K./Germany/
France/Australia/New
Zealand/Czech/Slovakia/
Hungary/Greece/Poland/
Russia
France/Australia/New
Zealand/Czech/Slovakia/
Hungary/Greece/Poland/
Russia
YES
2
Receive rejection
record
record
Used to set whether the rejected record is remained on the communication
report or not when receive is rejected by the receive rejection function.
report or not when receive is rejected by the receive rejection function.
Recorded
3,4 Time until resetting
when G3 DIS
cannot be received
in V.8 phase.
cannot be received
in V.8 phase.
When send is made via a satellite, if the DIS signal is not acknowledged, the
receive level is adjusted again and receive is tried again. This setting is used to
set the time until resetting.
receive level is adjusted again and receive is tried again. This setting is used to
set the time until resetting.
10s
5
Report table output
when in receive
rejection
when in receive
rejection
Used to set whether the communication report is outputted or not when receive
is rejected with the receive rejection function. ”Output” is enabled only when
SW134-2 is set to “0”.
is rejected with the receive rejection function. ”Output” is enabled only when
SW134-2 is set to “0”.
Not output
6
Sheet count method
in case of an error
in case of an error
Used to set whether an error page is included in the send quantity count in FAX
send or not. The default is: an error page is not counted.
send or not. The default is: an error page is not counted.
Send error pages are not
included.
included.
7
Not used
8
YES/NO of quick
memory send
setting
memory send
setting
Used to set whether the quick memory send ON/OFF is displayed on the menu
or not.
or not.
Setting is displayed.
SW
No.
Bit
No.
Item
Switch serection and function
Initial value
System
settings
Bit No.
Setting value
1
2
0
0
10 times
0
1
15 times
1
0
5 tmies
1
1
Non limitation
0
Not executes manual
calibration when re-
ceiving
calibration when re-
ceiving
1 Executes manual cali-
bration when receiving
1
Enable
0
Disable
1
Not recorded
0
Recorded
Bit No.
Setting value
3
4
0
0
8s
0
1
10s
1
0
12s
1
1
14s
1
Output
0
Not output
1
Send error pages are
included.
included.
0
Send error pages are
not included.
not included.
1
Setting is displayed.
0
Setting is not dis-
played.
played.
MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-52
135 1-4 Scanner resource
securing time out in
direct send
direct send
Binary input
Setting range: 20 - 50 sec (1step = 2 sec)
Setting range: 20 - 50 sec (1step = 2 sec)
26sec
5
Energy-saving reset
with an external TEL
with an external TEL
Used to set whether the machine is reset from the energy-saving mode or not
when the hand set of the external telephone is lifted in the energy-saving mode.
The default is: Not reset in Japan only.
when the hand set of the external telephone is lifted in the energy-saving mode.
The default is: Not reset in Japan only.
Reset (Complete reset)
6
Not used
7
External auditor
check
check
Used to set whether Enable/Disable of the FAX department management when
an external auditor is used. The default is Disable.
an external auditor is used. The default is Disable.
Check
8
Not used
136
1
RTC error
adjustment
adjustment
Used to correct advancement of the clock. The default is No Correction.
Not adjusts error
2-3 Not used
4-5 Time to display
destination when
the rapid key is
pressed
the rapid key is
pressed
Binary input
Adjusts 2 sec
6
Ring detection
signal selection
signal selection
Ring detection circuit
7
Waiting time of
carrier off in TCF
reception
carrier off in TCF
reception
4 sec
8
Not used
137 1-4 Outside line
connection number
setting 1 (1st digit)
setting 1 (1st digit)
Binary input
5-8 Outside line
connection number
setting 1 (2nd digit)
setting 1 (2nd digit)
Binary input
For Bit No., refer to the table of SW137-(1 - 4).
SW
No.
Bit
No.
Item
Switch serection and function
Initial value
System
settings
Bit No.
Setting
value
1
2
3
4
0
0
0
0
20sec
0
0
0
1
22sec
0
0
1
0
24sec
0
0
1
1
26sec
0
1
0
0
28sec
0
1
0
1
30sec
0
1
1
0
32sec
0
1
1
1
34sec
1
0
0
0
36sec
1
0
0
1
38sec
1
0
1
0
40sec
1
0
1
1
42sec
1
1
0
0
44sec
1
1
0
1
46sec
1
1
1
0
48sec
1
1
1
1
50sec
Bit No.
Setting
value
1
2
3
4
1
Reset (Complete
reset)
reset)
0
Not reset (Only 24V is
reset.)
reset.)
1
Not check
0
Check
1
Adjusts error
0
Not adjusts error
Bit No.
Setting value
4
5
0
0
Adjusts 2 sec
0
1
Adjusts 3 sec
1
0
Adjusts 4 sec
1
1
Adjusts 6 sec
0
Ring detection circuit
1
S i l i c o n DA A- R G D T
signal
signal
0
4 sec
1
2 sec
Bit No.
Setting
value
1
2
3
4
0
0
0
0
0
0
0
0
1
1
0
0
1
0
2
0
0
1
1
3
0
1
0
0
4
0
1
0
1
5
0
1
1
0
6
0
1
1
1
7
1
0
0
0
8
1
0
0
1
9
1
0
1
0
*
1
0
1
1
#
1
1
0
0
- (Pause)
Bit No.
Setting
value
1
2
3
4
MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-53
138 1-4 Outside line
connection number
setting 1 (3rd digit)
setting 1 (3rd digit)
Binary input
For Bit No., refer to the table of SW137.
5-8 Outside line
connection number
setting 1 (4th digit)
setting 1 (4th digit)
Binary input
For Bit No., refer to the table of SW137.
139 1-4 Outside line
connection number
setting 2 (1st digit)
setting 2 (1st digit)
Binary input
For Bit No., refer to the table of SW137.
5-8 Outside line
connection number
setting 2 (2nd digit)
setting 2 (2nd digit)
Binary input
For Bit No., refer to the table of SW137.
140 1-4 Outside line
connection number
setting 2 (3rd digit)
setting 2 (3rd digit)
Binary input
For Bit No., refer to the table of SW137.
5-8 Outside line
connection number
setting 2 (4th digit)
setting 2 (4th digit)
Binary input
For Bit No., refer to the table of SW137.
141 to 150 Not used
SW
No.
Bit
No.
Item
Switch serection and function
Initial value
System
settings
MX-FX10 SYSTEM SETTING 5-1
[5] SYSTEM SETTING
System setting
Set value(Default)
Remark
LIST PRINT/SET
LIST PRINT
SYSTEM SET LIST
JUNK FAX # LIST
ACC. USAGE LIST
JUNK FAX # LIST
ACC. USAGE LIST
LIST SETTING
(PRINT SELECTION)
(PRINT SELECTION)
TRANSMISSION
ALWAYS PRINTS/
ERROR ONLY*/
NEVER PRINTS
BROADCAST
ALWAYS PRINTS*/
ERROR ONLY/
NEVER PRINTS
ORIGINAL IMAGE PRINT SETTING ALWAYS PRINTS/
ERROR ONLY*/
NEVER PRINTS
RECEPTION
ALWAYS PRINTS/
ERROR ONLY/
NEVER PRINTS*
CONF. RECEPTION
ALWAYS PRINTS*/
NEVER PRINTS
LIST SETTING
(AUTO LISTING)
(AUTO LISTING)
AUTO PRINT REPT AT LIMIT (50)
Print/Not print*
PRINT DAILY AT DESIGNATED
TIME
TIME
NOT SETTING
INITIAL SETTING
DIAL MODE
Tone*/20PPS/10 PPS
PAUSE TIME
1,2* - 15sec
OWN PASSCODE SET
SPEAKER VOLUME
On-hook volume
High/Middle*/Low
Ringer volume
Line monitor volume
TX/RX end volume
Scan end volume
Tone volume
Line monitor volume
TX/RX end volume
Scan end volume
Tone volume
High/Middle*/Low/OFF
TX/RX END SOUND
SEND
PATTERN 1/2*/3
RECEIVE
PATTERN 1/2*/3
END SOUND LENGTH
2.0/2.5/3.0*/3.5/4.0sec
EXTENSION TEL
ON*/OFF
DISTINCTIVE RING
OFF*/STANDARD (For Australia, New
Zealand, Hong Kong only)
Zealand, Hong Kong only)
OFF*/STANDARD, PATTERN1/2/3/4/5(For
U.S.A./Canada only)
U.S.A./Canada only)
PBX SETTING MODE
ON/OFF*
For
Germany/
France only
Germany/
France only
REMOTE RECEPTION*1
0 - 5* - 9
ACCOUNT CONTROL
Enabled/Disabled*
ACCOUNT # SET
Program, Delete, Change
DATE & TIME SET
DAYLIGHT SAVING
TIME SETTING
TIME SETTING
ON*/OFF (For U.K./Germany/France/
Australia/New Zealand only)
ON/OFF* (For U.S.A./Canada)
Australia/New Zealand only)
ON/OFF* (For U.S.A./Canada)
DISABLE FAX PRINT HOLD
ON*/OFF
Click on the first or last page to see other MX-FX10 service manuals if exist.