DOWNLOAD Sharp MX-FWX1 Service Manual ↓ Size: 43.31 MB | Pages: 127 in PDF or view online for FREE

MX-7040N  MX-RB15 (CURL CORRECTION UNIT)  16 – 2

NOTE: Installation must be executed in the sequence of the com-

plex machine body, the paper feed option, and the paper
exit option.

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

NOTE: To prevent against falling during installation, extend the

stand rail.

1)

Attach the connection plates F/R (Packed items No.6, 7) and
fix them with the screws (Packed items No.4).

1)

Fix the shunt cable connection plate (Packed items No.9) with
the screws (Packed items No.2).

1)

Attach the rear upper cover (Packed items No.10) and fix it
with the screw (Packed items No.3).

1)

Fix the earth bracket (Packed items No.8) with the screws
(Packed items No.1).

NOTE: Use the outside screw holes for fixing.

1)

Return the stand rail to the original position.

2)

Connect the unit to the machine. 
Insert the pin in the machine side into the hole in the R side of
the unit.

MX-7040N  MX-RB15 (CURL CORRECTION UNIT)  16 – 3

NOTE: When the adjuster bolt is turned counterclockwise, the

height is decreased. When turned clockwise, the height is
increased.

NOTE: For the height and tilt adjustment, use the three adjuster

bolts under the unit.

Turn the adjustment nuts of the casters with a wrench in the arrow
direction to adjust the height. (When turning the adjustment nut one
rotation, the height of the curl correction unit is changed by about
1.75mm.)
• To increase the curl correction unit height, turn the nut in the

direction [A].

• To decrease the curl correction unit height, turn the nut in the

direction [B].

NOTE: Use the wrench attached to the finisher.

1)

Use adjuster bolt (1) to adjust the height so that the center of
the hole for the unit fixing screw in the F side is aligned with
the center marking-off line. 

2)

Use adjuster bolt (2) to adjust the height so that the center of
the hole for the unit fixing screw in the R side is aligned with
the center marking-off line. 

3)

Use adjuster bolt (3) so that the clearance between the
machine and the unit becomes uniform.

1)

Fix the unit to the machine with the step screws (Packed
items).

1)

Connect the three connectors of the unit to the machine, and
fix with the screws.

Ԙ

Ԛ

ԙ

MX-7040N  MX-CF11 (INSERTER)  17 – 1

MX-7040N

Service Manual

 

NOTE: When moving the inserter, use manpower of three or more

persons.

1)

Remove the fixing tape and the protection material from the
inserter.

* The quantity of safety plate is running-changed from 2 to 1 after
September, 2012 production.

1

Accessory cover

1

1

1

1

2

Tray unit front cover

1

1

1

1

3

Base cover (Tray unit)

1

1

1

1

4

Connection plate L 
(Finisher side)

1

---

---

1

5

Connection plate R 
(Finisher side)

1

---

---

1

6*

Safety plate

2

2

2

---

7

Earth plate

1

1

1

1

8

Connection plate L 
(Machine side)

1

1

---

---

9

Connection plate R 
(Machine side)

1

1

---

---

10

Black Mylar

1

1

---

---

11

Height adjustment saucer

4

4

4

4

12

"L" hinge pin 
(Tray unit front cover)

2

2

2

2

13

Screw (4 x 8L)

1

1

1

1

14

Blue screw (4 x 8L)

4

4

---

---

15

Blue screw (3 x 8L)

1

---

---

---

16

Screw (4 x 12L)

3

3

3

3

17

Screw (4 x 20L)

2

2

2

2

18

Screw (4 x 6L)

6

6

---

---

19

Front surface cushion (Long)

2

2

2

2

20

Front surface cushion (Short)

1

1

1

1

21

Winding bushing 6 x 8L

2

2

2

2

22

Gasket (for Taiwan only)

3

1

2

2

3

3

MX-7040N  MX-CF11 (INSERTER)  17 – 2

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

1)

Attach the front surface cushion (Long) (Packed items No. 19)
and the front surface cushion (Short) (Packed items No. 20) to
the reference as shown below.

1)

Attach the Black Mylar (Packed items No.10) to the paper
guide B.

Attach the Black Mylar to the downstream side of the paper
guide.

Attach to the notch in the rear side as the reference.

2)

Fix the connection plate L/R (Finisher side) (Packed items
No.4 and 5) to the paper exit side of the inserter with the
screws (Packed items No.18 Screw 4x6L).

3)

Install the paper guide B (bundled with the decurler unit No.12)
to the paper exit side of the inserter with the screws (bundled
with the decurler unit No.1).

NOTE: When connecting the MX-RB13 to the back, attach the

paper guide D (bundled with the relay unit No. 9).

1)

Remove the earth plate from the lower section of the inserter
and turn the removed earth plate back and attach it as shown
in the photo below..

2)

Attach the earth plate (Packed items No.7), and fix it with the
screw (Packed items No.18).

Cushion (Long)

Cushion (Long)

Cushion (Short)

Cushion (Long)

Cushion

Cushion

Cushion (Short)

reference

reference

reference

reference

reference

reference

Attach the cushion (Short) in
series with the cushion (Long).

R side

Black Mylar

Notch

Earth plate

1

1

1

1