DOWNLOAD Sharp MX-B382 (serv.man7) Service Manual ↓ Size: 20.77 MB | Pages: 60 in PDF or view online for FREE

MX-B382/B402  MX-CSX1/CSX2, MX-DS13/DS14 (500-SHEET PAPER FEED UNIT A/B, BASE STAND, ADDITIONAL STAND)  2 – 3

3)

Slide the left cabinet to the front side.

4)

Remove the screw.

5)

Open the side cover.

6)

While pressing the pawl, remove the rear cabinet.

7)

Disengage the harness from notch in the 500-sheet paper feed
unit.

8)

Close the side cover.

1)

Remove the tray.

MX-CSX1

MX-CSX2

MX-B382/B402  MX-CSX1/CSX2, MX-DS13/DS14 (500-SHEET PAPER FEED UNIT A/B, BASE STAND, ADDITIONAL STAND)  2 – 4

2)

Remove the screw. Disengage the pawl, and remove the rear
cabinet.

1)

Turn the MX-DS13 upside down, and attach the adjusters to
the bottom.

NOTE: Note that the four adjusters have their own attaching posi-

tion. Insert the screwed pin of an adjuster into the adjust-
ment knob.

NOTE: The adjusters must be attached so that they are in higher

positions than the casters when the MX-DS13 is placed on
a floor. If any adjuster is in lower position than a caster, or if
the four adjusters are in different height positions, the
machine may fall down during installation.

* The following descriptions are based on the case where the MX-

CSX2 is installed. To install the MX-DS14, perform the same pro-
cedures.

1)

Put the MX-CSX2 on the MX-DS13 by fitting with the position-
ing mark.

NOTE: To lift the machine with the MX-DS14, the MX-CSX2 and

the MX-CSX1, or the main unit installed, use two or more
persons.

NOTE: Since the left cabinet slides freely, be careful not to allow it

to slide when lifting the machine.

2)

Loosen the manual screws.

MX-B382/B402  MX-CSX1/CSX2, MX-DS13/DS14 (500-SHEET PAPER FEED UNIT A/B, BASE STAND, ADDITIONAL STAND)  2 – 5

3)

Slide the caster unit connection plate FL until it stops, and
tighten the manual screw to fix it.

4)

Loosen the manual screws.

5)

Slide the caster unit connection plate FR until it stops, and
tighten the manual screw to fix it.

6)

Attach the included caster unit connection plate B to the bot-
tom of the rear side, and fix it with the included screw.

* The following descriptions are based on the case where the MX-

CSX1 is installed. To install another model (other than MX-CSX1)
to the MX-DS14, perform the same procedures.

1)

Put the MX-CSX1 on the MX-DS14 by fitting with the position-
ing mark.

NOTE: To lift the machine with the main unit installed, use two or

more persons.

NOTE: Since the left cabinet slides freely, be careful not to allow it

to slide when lifting the machine.

MX-B382/B402  MX-CSX1/CSX2, MX-DS13/DS14 (500-SHEET PAPER FEED UNIT A/B, BASE STAND, ADDITIONAL STAND)  2 – 6

* When the MX-CSX1 is put on the machine, it is automati-

cally locked on the left rear and right rear side.

* When removing the MX-CSX1 from the MX-DS14, open the

right cabinet and the left cabinet of the MX-DS14, press the
lock to release it, and remove at the same time.

2)

Slide the front cover of the MX-DS14 to the left side to remove.

3)

Attach the metal fixture included in the package, and fix it with
the screws included in the package.

NOTE: Be careful of the fixing positions of the screws as shown

below.

4)

Slide the front cover of the MX-DS14 to the right side to install.

5)

To install the main unit after installing the MX-CSX1, go to "G."
When installation of the main unit to the MX-DS14 is com-
pleted, go to "I." When installation of the cabinet or the tray is
completed, go to "K."