Sharp MX-6500N / MX-7500N (serv.man2) Handy Guide ▷ View online
Jam Cause Codes
57
Document Solutions After Sales Service
Code
Content
Code
Content
STOP_JAM
Emergency stop request JAM
(controller request)
NO_MATCH
Parameter inconsistency
D.S.P.F. Sensor Location:
Code
Content
Code
Content
SPPD1_N
SPPD1 not reached JAM
SPPD2_N
SPPD2 not reached JAM
SPPD3_N
SPPD3 not reached JAM
SPPD4_N
SPPD4 not reached JAM
SPPD5_N
SPPD5 not reached JAM
SPOD_N
SPOD not reached JAM
SPPD1_S
SPPD1 remaining JAM
SPPD2_S
SPPD2 remaining JAM
SPPD3_S
SPPD3 remaining JAM
SPPD4_S
SPPD4 remaining JAM
SPPD5_S
SPPD5 remaining JAM
SPOD_S
SPOD remaining JAM
SPSD_SCN
Exposure start notification timer end
P_SHORT
PPD2 JAM (Finisher communication
error detection)
SDFS_S
Paper JAM
ICU_REQ
ICU factor stop JAM
STOP_JAM
Emergency stop JAM
Jam Cause Codes
58
Document Solutions After Sales Service
MX-FN19/20 Sensor Location:
Code
Content
Code
Content
FED_N
Finisher inlet port not-reached JAM
FED_S
Finisher inlet port remaining JAM
FFPD_N
Saddle section not-reached JAM
FFPD_S
Saddle section remaining JAM
FIN_TIME
Finisher paper early reaching JAM
FHS_N
Finisher paper exit not-reached JAM
FHS_S
Finisher paper exit remaining JAM
FSHS_N
Saddle transport not-reached JAM
FSHS_S
Saddle transport remaining JAM
FSFS_N
Saddle paper exit not-reached JAM
FSFS_S
Saddle paper exit remaining JAM
FSTPLJ
Finisher staple JAM
FPNCHJ
Finisher punch JAM
FSSTPLJ
Saddle staple JAM
PDPPD1_N Finisher interface inlet port not-reached
JAM
PDPPD1_S Finisher interface inlet port remaining JAM
PDPPD2_N Finisher interface inlet port not-reached
JAM
PDPPD2_S Finisher interface inlet port remaining JAM
FSSMJ
Finisher staple shift motor JAM
FDRLMJ
Finisher paper exit roller lift motor JAM
FSDMJ
Finisher saddle motor JAM
FGMJ
Finisher gripper motor JAM
FSPTMJ
Finisher saddle paper transport motor JAM
FIN_PAOF
Finisher paper attribute data reception
overflow
Jam Cause Codes
59
Document Solutions After Sales Service
MX-RB15 Sensor Location:
MX-RB13 Sensor Location:
MX-FN21/22 Sensor Location:
Code
Content
Code
Content
FNS101_N Inlet port not-reached JAM (FN pass)
FNS101_S
Inlet port remaining JAM (FN pass)
FNS102_N Paper exit not-reached JAM
FNS102_S
Paper exit remaining JAM
FNM110
Paper exit roller lift motor JAM
FNM117
Gripper motor JAM
FNM115
Staple JAM
FNM114
Discharged paper HOLD motor JAM
FNM113
Paper rear edge fall motor JAM
FNM116
Gripper arm motor JAM
FNM112
Paper alignment roller lift motor JAM
FNM118
Paper rear edge hold motor JAM
FCM102
Punch JAM
FNPAOF
Paper attribute data reception overflow
FNTIME
Early reaching JAM
FSS201_N
Saddle inlet port pass sensor delay JAM
FSS201_S
Saddle inlet port pass sensor remaining JAM
FSS203_N
Saddle vertical pass sensor delay JAM
FSS226_N
Saddle transport paper pass sensor 1 delay
JAM
FSS226_S
Saddle transport paper pass sensor 1
remaining JAM
FSS227_N
Saddle paper exit pass sensor 2 delay JAM
FSS227_S
Saddle paper exit pass sensor 2 remaining
JAM
FSM202
Saddle section saddle alignment motor JAM
FSM203
Saddle section lead edge stopper motor JAM
FSM204
Saddle section folding roller guide motor JAM FSM210
Saddle section rear edge hold motor JAM
FSM211
Saddle section rear edge shift motor JAM
FSM213
Saddle section SADDLE flapping motor JAM
FSM214
Saddle section SEPERATION motor JAM
FSM206
Saddle section folding motor JAM
FSM205
Saddle section PUSH motor JAM
Code
Content
DCS100_N Decurler unit transport pass sensor not-
reached JAM
DCS100_S
Decurler unit transport pass sensor remaining
JAM
DCTIME
Early reaching JAM
DCPAOF
Paper attribute data reception overflow
Code
Content
PIS150_N
Transport unit pass sensor not-reached JAM
PIS150_N
Transport unit pass sensor remaining JAM
Jam Cause Codes
60
Document Solutions After Sales Service
MX-TM10 Sensor Location:
MX-FD10 Sensor Location:
Code
Content
FTS103_N
Trimmer paper exit sensor delay JAM
FTS103_S
Trimmer paper exit sensor remaining JAM
FTS101_N
Trimmer inlet port sensor delay JAM
FTS101_S
Trimmer inlet port sensor remaining JAM
FTM103
Trimmer section inlet port separation motor
JAM
FTM104
Trimmer section paper exit separation motor
JAM
FTM102
Trimmer section registration motor JAM
FTM106
Trimmer section CUTTER motor JAM
FTM105
Trimmer section bundle press motor JAM
Code
Content
FLS30_N
Speed Reduction timing sensor delay JAM
FLS30_S
Speed Reduction timing sensor remaining JAM
FLS31_N
Separation timing sensor delay JAM
FLS31_S
Separation timing sensor remaining JAM
FLS32_N
Folding position adjustment sensor delay JAM
FLS32_S
Folding position adjustment sensor remaining
JAM
FLS33_N
Upper stopper section paper detection sensor
delay JAM
FLS33_S
Upper stopper section paper detection sensor
remaining JAM
FLS22_N
Outlet port 1 sensor delay JAM
FLS22_S
Outlet port 1 sensor remaining JAM
FLS27_N
Folding tray empty sensor delay JAM
FLS27_S
Folding tray empty sensor remaining JAM
FLS20_N
Inlet port sensor delay JAM
FLS20_S
Inlet port sensor remaining JAM
FLS21_N
Outlet port 2 sensor delay JAM
FLS21_S
Outlet port 2 sensor remaining JAM
FLM8
Folding section upper stopper motor JAM
FLM9
Folding section 3-fold stopper motor JAM
FLM10
Folding section lead edge hold guide motor JAM
FLM7
Folding section folding tray paper exit motor
JAM
FLENT_ERR Entry start time out JAM
FLEJT_ERR Eject start time out JAM
FLEJT_ERR Eject start time out JAM
Click on the first or last page to see other MX-6500N / MX-7500N (serv.man2) service manuals if exist.