Sharp MX-5500N / MX-6200N / MX-7000N (serv.man18) Peripheral ▷ View online
MX-FNX4 DISASSEMBLY AND ASSEMBLY 6 – 17
1) Remove the screw [1], and remove the stopper [2].
2) Remove the two screws [3], and disconnect the connector [4].
3) Insert your finger into the hole in the back of the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
clutch, and lift the No. 2 tray [5].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
i. Removal of grate-shaped lower guide
1)
1)
Remove the ten screws [1], and remove the grate-shaped
lower guide [2].
lower guide [2].
CAUTION: When installing, be careful not to damage the grate-
shaped lower guide by hanging it to the sensor flag arm
on the delivery side.
on the delivery side.
j. PCB cover
1)
1)
Remove the seven screws [1], and remove the PCB cover [2].
k. Removal of inlet port feed unit
1)
1)
Disconnect the connectors [1] at four positions, and remove
the harness from the clamp [2].
the harness from the clamp [2].
[2]
[1]
[4]
[3]
[3]
[5]
[6]
[1]
[1]
[1]
[2]
[1]
[1]
[2]
[1]
[1]
[2]
MX-FNX4 DISASSEMBLY AND ASSEMBLY 6 – 18
2) Remove the four screws [3].
3) Open the upper cover [4], and remove the inlet port feed unit
3) Open the upper cover [4], and remove the inlet port feed unit
[5].
l. Removal of saddle unit
1) Disconnect the two connectors [1], and remove the harness
1) Disconnect the two connectors [1], and remove the harness
from the clamp [2] at three positions.
2) Remove the harness from the clamps [2] at two positions on
the bottom of the delivery side.
3)
Remove the two screws [4].
4)
Remove the three screws [5].
5)
Remove the saddle unit [6] from the paper feed side.
CAUTION: When installing saddle unit, arrange so that the Mylar
[1] on the top of the saddle section is on the outside of
the feed guide plate [2]. If it is installed on the inside,
feed operation may be faulty.
the feed guide plate [2]. If it is installed on the inside,
feed operation may be faulty.
[3]
[3]
[5]
[4]
[1]
[3]
[2]
[3]
[2]
[4]
[6]
[5]
[5]
[1]
[2]
MX-FNX4 DISASSEMBLY AND ASSEMBLY 6 – 19
(4) Stitcher base unit (MX-FNX4)
a. Removal of front cover
1) Open the front cover [1], and remove the clip [2].
2) Lift the front cover [1], and remove it.
1) Open the front cover [1], and remove the clip [2].
2) Lift the front cover [1], and remove it.
b. Removal of saddle inlet front inside cover
1) Remove the three screws [1], and remove the saddle inlet front
1) Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
c. Removal of front inside upper cover
1) Remove the four screws [1], and remove the front inside upper
1) Remove the four screws [1], and remove the front inside upper
cover [2].
d. Removal of front inside lower cover
1)
1)
Remove the screw [1], and remove the roller knob [2].
2)
Remove the four screws [3], and remove the front inside lower
cover [4].
cover [4].
e. Removal of stitcher base unit
1)
1)
Remove the E-ring [1], and remove the shaft [2] and the roller
[3].
[3].
2)
Pull out the stitcher base unit [4] toward you.
(5) Positioning plate unit (MX-FNX4)
a. Removal of front cover
1)
1)
Open the front cover [1], and remove the clip [2].
2)
Lift the front cover [1], and remove it.
[1]
[2]
[1]
[2]
[1]
[1]
[2]
[1]
[3]
[2]
[3]
[1]
[4]
[1]
[3]
[2]
[4]
[1]
[2]
MX-FNX4 DISASSEMBLY AND ASSEMBLY 6 – 20
b. Removal of rear cover
1) Shift the tray cable cover [1] to the tray side, and remove it.
2) Remove the six screws [2], and lift and remove the rear cover
1) Shift the tray cable cover [1] to the tray side, and remove it.
2) Remove the six screws [2], and lift and remove the rear cover
[3].
c. Removal of saddle inlet front inside cover
1) Remove the three screws [1], and remove the saddle inlet front
1) Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
d. Removal of front inside upper cover
1) Remove the four screws [1], and remove the front inside upper
1) Remove the four screws [1], and remove the front inside upper
cover [2].
e. Removal of front inside lower cover
1)
1)
Remove the screw [1], and remove the roller knob [2].
2)
Remove the four screws [3], and remove the front inside lower
cover [4].
cover [4].
f. PCB cover
1)
1)
Remove the seven screws [1], and remove the PCB cover [2].
g. Removal of saddle stitcher controller PCB
1)
1)
Remove the four screws [1] and sixteen connectors [2], and
remove the saddle stitcher controller PCB [3].
remove the saddle stitcher controller PCB [3].
[2]
[1]
[3]
[2]
[1]
[2]
[1]
[1]
[2]
[1]
[3]
[2]
[3]
[1]
[4]
[1]
[1]
[2]
[1]
[1]
[1]
[1]
[2]
[3]
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man18) service manuals if exist.