DOWNLOAD Sharp MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man8) Service Manual ↓ Size: 40.14 MB | Pages: 127 in PDF or view online for FREE

MX-5141N  MX-DE21 (STAND 2000 SHEET PAPER DRAWER)  5 – 1

MX-5141N

Service Manual

 

If the connector is removed first, it may be damaged during the
installation procedures. Therefore, keep it packed while un-box-
ing.  and unpack it only when connecting the connector to the
machine.

* If the connector is removed first, it may be pinched in the install-

ing procedures. Therefore, keep it packed when unpacking the
package, and unpack it when connecting the connector to the
machine.

Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation. 

1)

Turn each adjuster to fix the desk unit.

1)

Remove the connection plate covers of the both sides of the
main unit.

1

Fixing screws (M4 x 8)

4

MX-5141N  MX-DE21 (STAND 2000 SHEET PAPER DRAWER)  5 – 2

2)

Put the main unit on the desk unit.

* Use man power of four persons or more to lift the main unit.

* Place the main unit on the desk unit slowly by fitting the

external lines. Check to insure that the positioning pin on the
top of the desk unit is securely engaged in the positioning
groove of the main unit.

3)

Remove the No. 2 paper feed tray.

4)

Pull out the No. 3 paper feed tray until it stops.

5)

Lift the connection plates on the right and left of the main unit
front side, and fix them with the fixing screws (Packed items).

6)

Replace the tandem tray and No. 2 trays to the original posi-
tions.

7)

Lift the connection plates, and fix them with the fixing screws
(Packed items).

MX-5141N  MX-DE21 (STAND 2000 SHEET PAPER DRAWER)  5 – 3

8)

Install the connection plate covers.

1)

Pull out the tandem tray. Remove the four screws and remove
the caution sheet.

1)

Remove the screw from the back of the main unit. Remove the
connector cover.

2)

Connect the connector.

3)

Install the connector cover and fix it with a screw.

1)

Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.

MX-5141N  MX-DE21 (STAND 2000 SHEET PAPER DRAWER)  5 – 4

1)

Open the tandem paper feed tray.

2)

Push down the paper feed base plate gently, hold the hooks
and remove A4 size regulation plate.

3)

Fit the A4 size regulation plate to A4 size, and attach it.

* Be careful to place and direction that install the sheet.

4)

Close the tandem paper feed tray.

5)

Execute SIM26-2 to set tray size for Tray3.

The image lead edge position and the off-center adjustment value
of the desk unit have been set to the average value when shipping
from the factory. 
Therefore, this adjustment must be performed only when the judg-
ment is made to execute it through checking the print image.

1)

Enter the SIM50-28 mode.

2)

Select [SETUP/PRINT] ADJ with the key button.

3)

Select [ALL] with the key button.

By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.

? [LEAD]: Print image lead edge image position adjustment

? [OFFSET]: Print image off-center adjustment

When [ALL] is selected, both of the above two items are
executed simultaneously.

4)

Select a paper feed tray to be adjusted.

5)

Press [EXECUTE] key.

The patch image (adjustment pattern) is printed out.

 

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

2&ǂ$'-

%.0$*ǂ$'-

63)ǂ$'-

6(78335,17ǂ$'-

5(68/7

'$7$

 

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

/($'

2))6(7

$//

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

(;(&87(

0)7

&6

$'8

&6

&6

&6

/&&