Sharp MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man8) Service Manual ▷ View online
MX-5141FN MX-4140N/4141N/5140N/5141N (MAIN UNIT) 2 – 8
4)
Write down the displayed skew level.
(Meaning of the skew level value and the adjustment proce-
dure)
(Meaning of the skew level value and the adjustment proce-
dure)
* If "OK" is displayed for all items of C, M, and Y (SKEW),
there is no need to perform the adjustment.
* When "R" is displayed at the head of the value, turn the LSU
skew adjustment screw clockwise.
* When "L" is displayed at the head of the value, turn the LSU
skew adjustment screw counterclockwise.
* The turning amount of the adjustment screw corresponds to
each adjustment value. C, M, and Y indicate numbers of
clicks.
clicks.
The display value is rounded at the decimal point.
* "C, M, and Y(SKEW)" shows the number of adjustment click
steps for each adjustment screw of C, M, and Y.
Contents in ( )
MIAN, SUB: Difference from the previous adjustment value of
image registration.
image registration.
Example:
If 105 for this time and 103 for the previous time,
it is displayed as 105.0 (+2.0).
it is displayed as 105.0 (+2.0).
SKEW: Judgment of the LSU skew adjustment result. OK or
NG.
NG.
PHASE: OPC drum phase adjustment value of the previous
time
time
5)
Repeat the procedures 2) to 4) again, and check to confirm
that C, M, and Y (SKEW) are OK.
that C, M, and Y (SKEW) are OK.
If any of them is NG, turn the LSU skew adjustment screw of
the corresponding color to adjust.
the corresponding color to adjust.
NOTE: When an abnormality occurs, "ERROR" is displayed.
In this case, check each drive section and the process sec-
tion.
tion.
Display/
Item
Content
Display
Default
NOTE
MAIN F
C
Registration adjustment value main scanning
direction (Cyan laser writing position F side)
direction (Cyan laser writing position F side)
1.0 - 199.0
100
M
Registration adjustment value main scanning
direction (Magenta laser writing position F side)
direction (Magenta laser writing position F side)
1.0 - 199.0
100
Y
Registration adjustment value main scanning
direction (Yellow laser writing position F side)
direction (Yellow laser writing position F side)
1.0 - 199.0
100
MAIN R
C
Registration adjustment value main scanning
direction (Cyan laser writing position R side)
direction (Cyan laser writing position R side)
1.0 - 199.0
100
M
Registration adjustment value main scanning
direction (Magenta laser writing position R side)
direction (Magenta laser writing position R side)
1.0 - 199.0
100
Y
Registration adjustment value main scanning
direction (Yellow laser writing position R side)
direction (Yellow laser writing position R side)
1.0 - 199.0
100
SUB
C
Registration adjustment value sub scanning direction
(Cyan drum
(Cyan drum
1.0 - 199.0
100
M
Registration adjustment value sub scanning direction
(Magenta drum
(Magenta drum
1.0 - 199.0
100
Y
Registration adjustment value sub scanning direction
(Yellow drum
(Yellow drum
1.0 - 199.0
100
SKEW
C
Print skew amount calculation result (Cyan)
-99.9 - 99.9
0
If the value is positive (+), "L" is displayed at the head of the
value. If negative (?), "R" is displayed.
If the value is in the range of ?2.1 - +2.1, "(OK)" is displayed at
the bottom of the value. In the other cases, "(NG)" is displayed.
value. If negative (?), "R" is displayed.
If the value is in the range of ?2.1 - +2.1, "(OK)" is displayed at
the bottom of the value. In the other cases, "(NG)" is displayed.
M
Print skew amount calculation result (Magenta)
-99.9 - 99.9
0
Y
Print skew amount calculation result (Yellow)
-99.9 - 99.9
0
PHASE
OPC drum phase adjustment value
1 - 8
1
C
Y
M
MX-5141FN MX-4140N/4141N/5140N/5141N (MAIN UNIT) 2 – 9
(2)
Copy color balance and density check
MEMO: Before checking the copy color balance and density, be
sure to execute the following jobs.
sure to execute the following jobs.
* Execute the high density image correction (Process correction)
forcibly. (SIM 44-6)
* Execute the half-tone image correction forcibly. (SIM 44-26)
Method 1
Make a copy of the gray test chart (UKOG-0162FCZZ) and a copy
of the servicing color test chart (UKOG-0326FCZZ/UKOG-
0326FC11), and check that they are proper.
of the servicing color test chart (UKOG-0326FCZZ/UKOG-
0326FC11), and check that they are proper.
a. Note for execution of the color balance and density check in the
color copy mode
color copy mode
To check the copy color balance and density, use the gray test
chart (UKOG-0162FCZZ) and the servicing color test chart
(UKOG-0326FCZZ/UKOG-0326FC11). Set the copy density
level to "3" in the Text/Printed Photo mode (Manual), and make a
copy.
chart (UKOG-0162FCZZ) and the servicing color test chart
(UKOG-0326FCZZ/UKOG-0326FC11). Set the copy density
level to "3" in the Text/Printed Photo mode (Manual), and make a
copy.
At that time, all the color balance adjustments in the user adjust-
ment mode must be set to the default (center).
ment mode must be set to the default (center).
In addition, be sure to use the specified paper for color.
b. Note for checking the monochrome copy mode density
To check the density, use the gray test chart (UKOG-0162FCZZ).
Set the copy density level to "Manual 3" in the Text/Printed Photo
mode (Manual).
Set the copy density level to "Manual 3" in the Text/Printed Photo
mode (Manual).
In addition, all the color balance adjustments in the user adjust-
ment mode must be set to the default (center).
ment mode must be set to the default (center).
Check with the gray test chart (UKOG-0162FCZZ)
In the copy density check with the gray test chart, check to insure
the following conditions.
the following conditions.
NOTE: For the color (gray) balance, use the servicing color test
chart (UKOG-0326FCZZ/UKOG-0326FC11) to check.
Check with the servicing color test chart (UKOG-0326FCZZ/
UKOG-0326FC11)
UKOG-0326FC11)
In the copy color balance check with the servicing color test chart,
check to insure the following conditions.
check to insure the following conditions.
1
2
3
4
5
6
7
8
9
10
W
SHARP GRAY CHART
SHARP gray chart
Patch 1 is
slightly copied.
slightly copied.
Patch 2 is copied.
(Color copy)
1
2
3
4
5
6
7
8
9
10
W
SHARP GRAY CHART
SHARP gray chart
Patch 1 is not copied.
Patch 2 is
slightly copied.
slightly copied.
Patch 3 is copied.
(Black-and-white copy)
Serviceman chart (Color patch section)
The densities of patches 1 - 6 of
each color are properly balanced.
each color are properly balanced.
Patch 7 is slightly
copied or not copied.
copied or not copied.
(Color copy)
MX-5141FN MX-4140N/4141N/5140N/5141N (MAIN UNIT) 2 – 10
a. Color copy check items (Check to confirm the following:)
1)
There are 12 void areas.
2)
Registrations (one point for the main scanning, and one point
for the sub scanning) are not shifted.
for the sub scanning) are not shifted.
3)
The resolution of 5.0 (5 points) can be seen.
4)
The color difference in gray balance between the F and the R
sides is not so great.
sides is not so great.
5)
There are no white and black streaks.
6)
Color texts are clearly reproduced.
7)
The background density is not so light.
MX-5141FN MX-4140N/4141N/5140N/5141N (MAIN UNIT) 2 – 11
b. Monochrome copy check items (Check to confirm the following:)
1)
There are 12 void areas.
2)
The resolution of 4.0 (5 points) can be seen.
3)
The density difference between the F and the R sides is not so
great.
great.
4)
There are no white and black streaks.
5)
The background density is not so light.
6)
The black low-density gradation is copied slightly.
Click on the first or last page to see other MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man8) service manuals if exist.