DOWNLOAD Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man38) Service Manual ↓ Size: 27.15 MB | Pages: 121 in PDF or view online for FREE

MX-4100N  MX-4100N/4101N/5000N/5001N  1 – 6

12) Secure with fixing screw. Lower the DV lock lever until it clicks

closed.

13) Close the drum positioning unit, and tighten the blue screw.

14) Install the waste toner box (package part No. 3).

1)

Insert the power plug into the power outlet.

2)

With the front cabinet open, turn on the power switch on the
operation panel.

3)

With the front cabinet open, turn on the power switch on the
operation panel.

4)

With the front cabinet still open, enter simulation 25-2.

5)

After entering the simulation, close the front cabinet.

<State of switch>

ON

OFF

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

$7'(9($'-B/B.

$7'(9(92B0B.

$7'(9($'-B/B&

$7'(9(92B0B&

$7'(9($'-B/B0

$7'(9(92B0B0

$7'(9($'-B/B<

$7'(9(92B0B<

$7'(9($'-B0B.

$7'(9($'-B0B&

$7'(9($'-B0B0

$7'(9($'-B0B<

$7'(9(92B/B.

$7'(9(92B/B&

$7'(9(92B/B0

$7'(9(92B/B<

.

&

0

<

MX-4100N  MX-4100N/4101N/5000N/5001N  1 – 7

6)

Select K, C, M, Y and then press the [EXECUTE] button. The
system then performs the simulation, samples the toner den-
sity control sensor value, and sets (stores in memory) the
average sensor detection level as the control level for the ref-
erence toner density. (Operating times: approx. 3 minutes)

Note: Be sure to select all of the four colors: K, C, M, Y

7)

After the machine completes cycling, exit the simulation mode
by pressing the [CA] key on the main unit.

* The life of each toner cartridge is as follows:

Black toner cartridge: equivalent to approximately 18K (A4/LT
5%)
Color toner cartridge: equivalent to approximately 15.0K (A4/LT
5%)

1)

Shake the toner cartridge (package part No. 1) horizontally
several times.

2)

Remove the heat seal.

3)

Open the front cabinet, and insert each toner cartridge.

* Be sure to install the color cartridges to their proper posi-

tions. Avoid installation to a different color position.

* Do not forcibly insert the toner cartridge.

Keep holding the cartridge and completely insert it.

* When the machine is transported with the developing unit

removed, be sure to remove the toner cartridge. (If not, toner
may be clogged.)
[Color toner cartridge positions]

4)

Insert the cartridge securely until it locks.

* Dust from the transfer belt or shutter or some other adjacent part

may fall onto the LSU during transport or installation. Be sure to
clean the dust-proof glass before checking the image quality.

1)

Open the front cabinet.

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

$7'(9($'-B/B.

$7'(9(92B0B.

$7'(9($'-B/B&

$7'(9(92B0B&

$7'(9($'-B/B0

$7'(9(92B0B0

$7'(9($'-B/B<

$7'(9(92B0B<

$7'(9($'-B0B.

$7'(9($'-B0B&

$7'(9($'-B0B0

$7'(9($'-B0B<

$7'(9(92B/B.

$7'(9(92B/B&

$7'(9(92B/B0

$7'(9(92B/B<

.

&

0

<

MX-4100N  MX-4100N/4101N/5000N/5001N  1 – 8

2)

Remove the waste toner box.

3)

Detach the LSU cleaning bar from the front cover.

4)

Turn the felt side of the cleaning bar downward and insert it.
Slide it back and forth a few times to clean the LSU dust-proof
glass.

5)

Replace the LSU claning bar to the front cover and attach the
waste toner box.

6)

Close the front cabinet.

1)

Install the paper exit tray (package part No. 4) (A) to the upper
section of the right door.
Install the paper exit full detection actuator (package part No.
5) (B).
* Be careful of the direction of the paper exit full detection

actuator.

1)

Install the paper holding arm unit (package part No. 6).
* If the MX-FNX9 (Inner Finisher) or the MX-RBX3 (Interface

Unit)  is installed when installing the main unit, do not install
the paper holding arm unit and the paper exit full detection
actuator.

MX-4100N  MX-4100N/4101N/5000N/5001N  1 – 9

1)

Install the Operation Manual storage (package part No. 8)
cover to the left side of the machine.
a)

First, insert the pawl on the lower side of the Operation
Manual pocket.

b)

Then, lift the pawl on the upper side and insert it, and slide
down to install.

* If the MX-FN10 (saddle finisher) is installed together with

installation of the machine, the Operation Manual storage
cover must be installed to the saddle finisher.

Change the tray setting in the "system setting" mode. If "Disabling
of Tray Settings" has been enabled in the system settings (adminis-
trator), the tray settings (except for the bypass tray) cannot be con-
figured.
1)

Press the [SYSTEM SETTINGS] key.

2)

Touch the [Paper Tray Settings] key.

3)

Touch the [Paper Tray Settings] key to configure the settings.
These settings specify the paper type, paper size, and func-
tions allowed for each paper tray. When the [Tray Settings] key
is touched, a list appears showing the trays and the current
settings.

4)

Touch the [Change] key in the above screen to change the set-
tings. The following settings can be configured.

1)

Pull out the paper tray.
Gently pull the tray out until it stops.
If paper remains in the tray, remove it.

2)

Adjust the guide plates A and B by squeezing their lock levers
and sliding them to match the vertical and horizontal dimen-
sions of the paper to be loaded.
The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.

1

1

2

Type

Select the type of paper that is loaded in the tray. 
The paper types that can be selected vary by paper 
tray.

Size

Select the paper size from the list. The paper sizes 
that can be selected vary by tray. The sizes that 
can be selected may also be restricted by the paper 
type selected above. 
If the desired size does not appear in the list, select 
[Custom Size] and directly enter the size (only for 
the bypass tray).

Feeding Approved 
Job

Select the modes that can be used. If there is a 
function that you do not wish to be used with the 
selected tray, disable the function. When the "Type" 
is other than plain paper, recycled paper, colored 
paper, or a user type, [Fax] and [Internet Fax] 
cannot be selected.

B

A