Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man38) Service Manual ▷ View online
MX-4100N MX-DEX8/DEX9 2 – 3
5)
Lift the connection plates on the right and left of the main unit
front side, and fix them with the fixing screws (package part
No. 2).
front side, and fix them with the fixing screws (package part
No. 2).
6)
Replace the No. 3 and No. 2 trays to the original positions.
7)
Lift the connection plates, and fix them with the fixing screws.
8)
Install the connection plate covers.
1
2
2
1
2
1
MX-4100N MX-DEX8/DEX9 2 – 4
D. Release the lock
1)
Pull out each tray.
2)
Turn and remove the fixing material, and remove the caution
sheet.
sheet.
3)
Attach the removed fixing material to the position shown in the
figure for storage.
figure for storage.
4)
Close the cassette which was pulled out.
E. Connector connection
1)
Remove the screw from the back of the main unit. Remove the
connector cover.
connector cover.
2)
Connect the connector.
3)
Split the removed connector cover along the perforated line.
4)
Install the connector cover and fix it with a screw.
NOTE:
Before turning on the power, check to insure that the fixing
material of the tray is disengaged. If the power is turned on
without disengaging the fixing material, a trouble may be
resulted.
Before turning on the power, check to insure that the fixing
material of the tray is disengaged. If the power is turned on
without disengaging the fixing material, a trouble may be
resulted.
MX-4100N MX-DEX8/DEX9 2 – 5
F. Turn on the power of the main unit
1)
Insert the power plug of the main unit into the power outlet.
2)
Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
Turn ON the power switch in the front cabinet of the main unit.
3)
Turn ON the power switch on the operation panel.
* For setting the tray size, refer to "Tray size setting" (1-9).
G. Off-center adjustment
(1) Adjustment with the simulation
1)
Run SIM50-10 using the keypad on the main unit.
The following screen appears:
The following screen appears:
2)
This screen allows you to configure the print off-center adjust-
ment value for each paper feed tray.
<Detailed Description>
ment value for each paper feed tray.
<Detailed Description>
3)
On the touch panel, press [
↓] to select "E: 50 :MAIN-CS3" or
"F: 50 : MAIN-CS4."
4)
Enter the desired adjustment value through the numeric key-
pad.
(This value, which defaults to 50, can be adjusted within the
range of 1 to 99).
• Reducing the adjustment value by 1 causes the main scan/
pad.
(This value, which defaults to 50, can be adjusted within the
range of 1 to 99).
• Reducing the adjustment value by 1 causes the main scan/
print position to shift by 0.1 mm toward the rear.
• Increasing the adjustment value by 1 causes the main scan/
print position to shift by 0.1 mm toward the front.
5)
After entering the adjustment value, press the [EXECUTE] key
on the touch panel to start printing and save the setting.
on the touch panel to start printing and save the setting.
6)
Check that the adjustment pattern image is printed in the cor-
rect position.
Measure the dimensions of the void areas on the front- and
rear-frame sides of the adjustment pattern image, and make
sure that the following conditions are met:
rect position.
Measure the dimensions of the void areas on the front- and
rear-frame sides of the adjustment pattern image, and make
sure that the following conditions are met:
No adjustment is needed if A - B = 0
±3.0 mm.
If the above condition is not met, do the following:
7)
Change the adjustment value.
(Enter a new adjustment value and press the [OK] key).
Changing the adjustment value by 1 shifts the position by
approximately 0.1 mm.
Repeat steps 4) to 6) until the condition shown in step 6) is sat-
isfied.
(Enter a new adjustment value and press the [OK] key).
Changing the adjustment value by 1 shifts the position by
approximately 0.1 mm.
Repeat steps 4) to 6) until the condition shown in step 6) is sat-
isfied.
8)
After you have completed the adjustment, exit from Simulation
mode by pressing the [CA] key.
mode by pressing the [CA] key.
ON
<State of switch>
ON
OFF
ǂǂǂ6,08/$7,21ǂǂ12
7(67
3$3(5&(17(52))6(76(783
$˖
˷̚
˹
˹
˖%.0$*
$˖
˖0$,10)7
%˖
˖0$,1&6
&˖
˖0$,1&6
'˖
˖0$,1&6
)˖
˖0$,1&6
(˖
˖0$,1/&&
*˖
˖0$,1$'8
+˖
˖68%0)7
,˖
˖68%&6
-˖
˖68%&6
.˖
˖68%/&&
/˖
2.
&/26(
(;(&87(
Item
Display
Description
Setting
range
Default
E
MAIN-CS3
Print off-center adjustment value
(tray 3)
(tray 3)
1 to 99
50
F
MAIN-CS4
Print off-center adjustment value
(tray 4)
(tray 4)
1 to 99
50
A-B = 0
3.0mm
+
-
B
A
MX-4100N MX-LCX1 3 – 1
MX-4100N
Service Manual
[3] MX-LCX1
1. Unpacking
A. Removal of the large capacity tray unit
B. Removal of the fixing material and packing
parts
1)
Remove the fixing material.
2)
Remove the fixing material and the packing parts.
3)
Remove the paper feed desk fixing screw.
C. Check the packed items
1)
Check that all the items are included in the package.
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
A. Turn off the power of the main unit
1)
Turn OFF the power switch on the operation panel.
No.
Names of bundles
Quantity
1
Mounting plate upper
2
2
Connection unit
1
3
Fixing screw A (Hexagon with seat, S-tight, M4 x 35)
4
4
Fixing screw B (Hexagon with seat, S-tight, M4 x 12)
2
5
Fixing screw C (screw 4 x 8 cup)
1
NOTE:
Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on
without removing the fixing screw, a trouble may be
resulted.
Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on
without removing the fixing screw, a trouble may be
resulted.
1
3
4
2
5
<State of switch>
ON
OFF
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man38) service manuals if exist.