Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N Handy Guide ▷ View online
SHARP
TEST SIMULATION
57
46
Copy/Scanner Image Density Adjustment
47 JPEG compression rate setting
48 Function setting for copy output
51 Heavy paper mode gamma adjustment
52 Heavy paper mode gamma default set
54 Engine half tone density adjustment (dither).
55 Drop out colour mode adjustment for Image
48 Function setting for copy output
51 Heavy paper mode gamma adjustment
52 Heavy paper mode gamma default set
54 Engine half tone density adjustment (dither).
55 Drop out colour mode adjustment for Image
Send mode.
58 Copy mode pseudo resolution setting
(smoothing process).
60 Sharpness adjustment (colour auto mode)
61 Area separation recognition setting
62 ACS operating condition setting
63 Copy low density adjustment
65 Colour correction table setting.
66 Watermark reproduction adjustment for
61 Area separation recognition setting
62 ACS operating condition setting
63 Copy low density adjustment
65 Colour correction table setting.
66 Watermark reproduction adjustment for
Copy/Printer
68 Auto resolution setting
74 Copy half tone balance adjustment
90 Set process operation of high compression
74 Copy half tone balance adjustment
90 Set process operation of high compression
PDF images
91 Black text reproduction adjustment
48
Magnification & Motor Adjustment
01 Scan image magnification adjust (Main scan)
05 Scan image magnification adjust (Sub scan)
06 Motor rotation speed adjustment
05 Scan image magnification adjust (Sub scan)
06 Motor rotation speed adjustment
49
ROM Version Upgrade
01 Firmware Upgrade Program
03 E Manual (Op manual) Update Program
05 Watermark Update Program
06 OCR Dictionary Update Program
10 ACU Firmware Update Program
03 E Manual (Op manual) Update Program
05 Watermark Update Program
06 OCR Dictionary Update Program
10 ACU Firmware Update Program
50
Image Position Adjustment
01 Lead edge/copy position & image loss
adjustment
05 Printer lead edge adjustment (sub scan)
06 SPF Lead edge/copy position adjustment
10 Print off-centre deviation adjustment.
12 Original centre deviation adjustment.
20 Manual colour registration adjustment.
22 Auto colour registration & drum adjustment.
23 Registration for temperature adjustment
06 SPF Lead edge/copy position adjustment
10 Print off-centre deviation adjustment.
12 Original centre deviation adjustment.
20 Manual colour registration adjustment.
22 Auto colour registration & drum adjustment.
23 Registration for temperature adjustment
setup
24 Auto registration & drum data display
27 Image loss adjustment (Fax/Scanner)
27 Image loss adjustment (Fax/Scanner)
50
Image Position Adjustment
28 Service automatic adjustment (OC/SPF
position & BK magnification etc)
51
Resist Roller Adjustment
01 Secondary transfer voltage ON timing
adjustment
02 Resist roller adjustment
53
Document Feeder Adjustment
06 SPF document tray size adjustment
07 SPF document tray size adjust value set.
08 SPF scanning position adjustment
09 SPF dirt detection setting
10 SPF dirt detection execution
07 SPF document tray size adjust value set.
08 SPF scanning position adjustment
09 SPF dirt detection setting
10 SPF dirt detection execution
55
MFP Data Setting
01 Engine soft switch setting
SW12-4
Enable 1
st
Transfer Belt lubrication
(applies yellow toner at specific
page count) – [50/60ppm only]:-
0 = Enabled, 1 = Disabled
page count) – [50/60ppm only]:-
0 = Enabled, 1 = Disabled
SW24-7
L4-11 detection disable (used for
troubleshooting when Finisher or
Centre Tray Unit is not installed).
0 = Enabled, 1 = Disabled
troubleshooting when Finisher or
Centre Tray Unit is not installed).
0 = Enabled, 1 = Disabled
SW27-4
Enable 1
st
Transfer Belt lubrication
at installation & maintenance when
TC1 Belt Counter Sim24-4 is cleared
[50/60ppm only]:-
0 = Enabled, 1 = Disabled
TC1 Belt Counter Sim24-4 is cleared
[50/60ppm only]:-
0 = Enabled, 1 = Disabled
02 Scanner soft switch setting
03 Controller soft switch setting
03 Controller soft switch setting
SW4-7
Custom Paper Size entry for Tray 1
0 = Disabled, 1 = Enabled
SW6-2
Ethernet Link Speed:-
0 = 100Base TX, 1 = 10Base T
SW6-3
Ethernet Duplex Mode:-
0 = Full, 1 = Half
SW6-4
Ethernet 100/1000 Link Speed:-
0 = 100Base TX, 1 = 1000Base T
SW9-5
Maintenance notification setting by
Printer MIB:-
Printer MIB:-
0 = Enabled, 1 = Disabled
SW17-3
A3 / Postcard Counter Mode
0 = Disabled, 1 = Enabled
SW18-6
Hide Device Counter Clear
(SIM24-6 to 24-15)
(SIM24-6 to 24-15)
0 = Hide [Default], 1 = Display
TEST SIMULATION
SHARP
58
55
MFP Data Setting
03 Controller soft switch setting
SW19-3
Auto output without stapling when
max. number of sheets is detected.
max. number of sheets is detected.
0 = Disabled, 1 = Enabled
SW22-5
Display toner remaining status:-
0= Disabled, 1 = Enabled/Display
SW24-7
Continuous print mode for OSA (job
queuing for EAM):-
queuing for EAM):-
0 = Job Queue Disabled
1 = Job Queue Enabled
1 = Job Queue Enabled
SW24-8
OSA Offline Mode (for external
accounting):-
accounting):-
0 = Disabled, 1 = Enabled
SW25-7
Custom Envelope size (Printer).
0 = Disabled, 1 = Enabled
SW27-8
Retain Scan to Desktop destination
for a certain period after a scan
operation.
for a certain period after a scan
operation.
0 = Disabled (Default), 1 = Enabled
SW28-3
Single Email alert notification for
customer.
customer.
0 = Disabled (Default), 1 = Enabled
SW28-4
Envelop mode – automatically
change to size tab screen.
change to size tab screen.
0 = Disabled,
1 = Enabled
1 = Enabled
SW29-7
Disable Pop Up Message for Data is
being cleared (DSK) & Settings of
machine changed by Web page:-
0 = Displayed (Default)
1 = Not displayed
being cleared (DSK) & Settings of
machine changed by Web page:-
0 = Displayed (Default)
1 = Not displayed
SW32-4
Printer MIB (Waste Toner
Remaining Status for Mac OSX):-
0 = RFC compliant (Default).
1 = Non RFC compliant.
Remaining Status for Mac OSX):-
0 = RFC compliant (Default).
1 = Non RFC compliant.
SW34-3
PDF/PS Preview Thumbnail for
Direct Print function:-
0 = Disabled (Default)
1 = Enabled
Direct Print function:-
0 = Disabled (Default)
1 = Enabled
SW35-1
Estimate Job Start time display
within job status:-
0 = Disabled (Default)
1 = Enabled
within job status:-
0 = Disabled (Default)
1 = Enabled
SW39-5
Print A5 size paper as A5R from
Bypass tray:-
0 = Disabled (Default),
1 = Enabled
Bypass tray:-
0 = Disabled (Default),
1 = Enabled
10 Special Stamp setting (Taiwan only)
56
MFP Data Export & Import
01 Transfer data execution (MFP/SRAM/
EEPROM to HDD)
02 Backup EEPROM/SSD/HDD operation data to
USB memory
03 Document filing data backup to USB memory
04 Job log data backup to USB memory
05 Export SIM22-06 (Adjustment & Settings
04 Job log data backup to USB memory
05 Export SIM22-06 (Adjustment & Settings
data) to USB memory
06 Output SIM23-02 Jam/Trouble data to USB
memory
07 Export Syslog data to USB memory
08 Export ICC Colour profile to USB memory
15 Import EEPROM data
99 Export ALL Log data (SIM56-02/04/05/06/07
08 Export ICC Colour profile to USB memory
15 Import EEPROM data
99 Export ALL Log data (SIM56-02/04/05/06/07
& SIM00-11) to USB memory
60
MFP Data Setting
01 SDRAM read/write test (MFP-SCU PWB)
61
LSU Writing Adjustment & Self-Test
01 LSU test (Polygon & BD detection check)
03 LSU power auto setup
04 LSU print image skew adjustment
11 LSU power correction (automatic)
12 LSU power manual correction
13 LSU power correction value reset/clear
14 LSU power setting collective input
03 LSU power auto setup
04 LSU print image skew adjustment
11 LSU power correction (automatic)
12 LSU power manual correction
13 LSU power correction value reset/clear
14 LSU power setting collective input
62
HDD Operation & Self-Test
01 HDD/SSD Card format
02 HDD partial read/write check
03 HDD read/write check (all areas)
06 Smart (HDD) self-diagnostic test
07 Smart (HDD) self-diagnostic error log
08 HDD/SSD Card format (excluding system &
02 HDD partial read/write check
03 HDD read/write check (all areas)
06 Smart (HDD) self-diagnostic test
07 Smart (HDD) self-diagnostic error log
08 HDD/SSD Card format (excluding system &
operation manual area)
10 Job completion list clear (with job log)
11 Document filing data clear
12 Enable/disable auto format for HDD trouble
13 HDD format (Operation manual & Watermark
11 Document filing data clear
12 Enable/disable auto format for HDD trouble
13 HDD format (Operation manual & Watermark
data only)
14 Delete document filing management data
20 Check operation of mirroring hard disk
20 Check operation of mirroring hard disk
SHARP
TEST SIMULATION
59
63
CCD Operation & Adjustment
01 Shading correction data display
02 Shading correction execution (force)
03 CCD gamma & colour correction adjustment
04 Scanner test chart patch density list display
05 CCD colour balance & gamma default setting
07 Register the standard target of copy mode
02 Shading correction execution (force)
03 CCD gamma & colour correction adjustment
04 Scanner test chart patch density list display
05 CCD colour balance & gamma default setting
07 Register the standard target of copy mode
auto colour balance adjustment (Service)
08 Set the standard copy mode auto colour
balance target to factory default (Service)
11 Set the standard target colour balance
adjustment (Factory)
64
Self-Test Print
01 Test print (Colour mode)
02 Test print (B/W mode)
04 Printer self-print test
05 Printer self-print test (PCL)
06 Printer self-print test (PS)
02 Test print (B/W mode)
04 Printer self-print test
05 Printer self-print test (PCL)
06 Printer self-print test (PS)
65
LCD Operation & Adjustment
01 LCD touch panel adjustment
02 LCD touch panel adjustment result display
05 Operation panel key input test
02 LCD touch panel adjustment result display
05 Operation panel key input test
66
Fax Control Settings & Adjustments
01 Fax Soft SW setting
SW24
Communication Signal sending level
(bits 1-8)
(bits 1-8)
SW27-4
V.34 mode function (call arrival):
0 = V.34 valid, 1 = V.34 invalid.
0 = V.34 valid, 1 = V.34 invalid.
SW27-5
V.34 mode function (polling when
calling):
0 = V.34 valid, 1 = V.34 invalid.
calling):
0 = V.34 valid, 1 = V.34 invalid.
SW27-6
V.34 mode function (manual
communication):
0 = V.34 valid. 1 = V.34 invalid.
communication):
0 = V.34 valid. 1 = V.34 invalid.
SW33-6,
SW33-7;
SW33-7;
Transmission cable amplitude
equaliser:-
00 = 0dB, 01 = 4dB
10 = 8dB, 11 = 12dB
equaliser:-
00 = 0dB, 01 = 4dB
10 = 8dB, 11 = 12dB
02 Country code default set (Fax)
03 Fax PWB (modem) controller memory check
04 Fax signal line check (Max level)
05 Fax signal line check (Soft SW setting level)
06 Fax list print (confidential registration)
07 Fax image memory printout (all data)
08 Fax sound message setup
03 Fax PWB (modem) controller memory check
04 Fax signal line check (Max level)
05 Fax signal line check (Soft SW setting level)
06 Fax list print (confidential registration)
07 Fax image memory printout (all data)
08 Fax sound message setup
66
Fax Control Settings & Adjustments
09 Fax signal line check (Soft SW setting)
10 Fax & Image data all memory clear
11 Voice signal check (line/speaker 300bps)
12 Voice signal check (line/speaker 300bps)
13 Register dial number for Sim 66-14/15/16
14 Adjust/check the time dial pulse (10bps)
15 Adjust/check the time dial pulse (20bps)
16 Adjust/check the send level DTFM signal
17 DTFM signal to send to line (Max level)
18 DTFM signal to send to line (Soft SW level)
21 Print various registration information
22 Set the sound volume of the handset (Japan)
29 Fax address book clear
30 Tel/LIU sensor status check
31 ON/OFF setting of output port (Tel/LIU)
32 Received data check (comparison)
33 Busy Tone/CNG/CED/FNET detect check
36 Check Send/Receive from modem.
39 Check Destination saved in Fax EEPROM
42 Rewrite PIC program installed on Fax box
43 Write program & adjustment values to PIC
10 Fax & Image data all memory clear
11 Voice signal check (line/speaker 300bps)
12 Voice signal check (line/speaker 300bps)
13 Register dial number for Sim 66-14/15/16
14 Adjust/check the time dial pulse (10bps)
15 Adjust/check the time dial pulse (20bps)
16 Adjust/check the send level DTFM signal
17 DTFM signal to send to line (Max level)
18 DTFM signal to send to line (Soft SW level)
21 Print various registration information
22 Set the sound volume of the handset (Japan)
29 Fax address book clear
30 Tel/LIU sensor status check
31 ON/OFF setting of output port (Tel/LIU)
32 Received data check (comparison)
33 Busy Tone/CNG/CED/FNET detect check
36 Check Send/Receive from modem.
39 Check Destination saved in Fax EEPROM
42 Rewrite PIC program installed on Fax box
43 Write program & adjustment values to PIC
installed on Fax
61 Display FAX related soft switch (151-250)
62 FAX receive data export in PDF format.
62 FAX receive data export in PDF format.
67
Printer Settings & Adjustments
17 Printer NVRAM clear
24 Printer colour balance auto adjustment
25 Printer colour balance manual adjustment
26 Set the target colour balance for printer
24 Printer colour balance auto adjustment
25 Printer colour balance manual adjustment
26 Set the target colour balance for printer
mode auto colour adjustment
27 Set the target colour balance for printer
mode auto colour adjustment (Service)
28 Set the printer mode auto colour adjustment
back to factory default (Service)
31 Printer calibration data clear
33 Printer screen gamma adjust. (PCL/PS)
34 Printer maximum density adjustment mode
36 Adjust the density in printer low density
33 Printer screen gamma adjust. (PCL/PS)
34 Printer maximum density adjustment mode
36 Adjust the density in printer low density
areas
41 2 colour print setup
42 2 colour print density setup
43 2 colour mode colour balance adjustment for
42 2 colour print density setup
43 2 colour mode colour balance adjustment for
printer
52 Printer default gamma check (PCL/PS)
54 Printer colour balance adjustment
54 Printer colour balance adjustment
TROUBLE CODES
SHARP
60
A0
Program Trouble
01 PCU ROM abnormality
02 SCU ROM abnormality
04 ACU/ACRE ROM error
10 MFP ROM error
15 Incompatible DSK Boot and program
02 SCU ROM abnormality
04 ACU/ACRE ROM error
10 MFP ROM error
15 Incompatible DSK Boot and program
firmware version
17 UI data & CPU firmware inconsistency.
18 Firmware mismatch error (ICU-Reus)
19 Boot error
20 Firmware & EEPROM conflict (MFP)
21 Firmware & EEPROM conflict (PCU)
22 Firmware & EEPROM conflict (SCU)
18 Firmware mismatch error (ICU-Reus)
19 Boot error
20 Firmware & EEPROM conflict (MFP)
21 Firmware & EEPROM conflict (PCU)
22 Firmware & EEPROM conflict (SCU)
C1
Main Charge Trouble
01 MC cleaner trouble (K)
[50/60ppm only]
03 MC cleaner trouble (C)
[50/60ppm only]
05 MC cleaner trouble (M)
[50/60ppm only]
07 MC cleaner trouble (Y)
[50/60ppm only]
10 Main charger trouble (K)
14 Main charger trouble (colour)
15 Main charger circuit trouble (K)
16 Main charger circuit trouble (colour)
40 MC PWB trouble
41 MC/TC PWB trouble
14 Main charger trouble (colour)
15 Main charger circuit trouble (K)
16 Main charger circuit trouble (colour)
40 MC PWB trouble
41 MC/TC PWB trouble
C4
PTC / 2TC Trouble
00 PTC trouble
05 PTC circuit trouble
20 Primary transfer output trouble
25 1TC circuit trouble
30 2
05 PTC circuit trouble
20 Primary transfer output trouble
25 1TC circuit trouble
30 2
nd
transfer output open trouble
31 2
nd
transfer output short circuit
35 2TC circuit trouble
40 TC PWB trouble
40 TC PWB trouble
CE
Network Communication Trouble
00 Network communication error
01 Network card is not installed or defective
02 FTP or Mail server is not found
03 Specified server does not correspond during
01 Network card is not installed or defective
02 FTP or Mail server is not found
03 Specified server does not correspond during
transmission
04 Invalid account/password (FTP server)
05 Invalid directory entered (FTP server)
06 Specified mail server (POP3) is not found
07 Invalid server account or password
08 The specified mail server (POP3) suspends
05 Invalid directory entered (FTP server)
06 Specified mail server (POP3) is not found
07 Invalid server account or password
08 The specified mail server (POP3) suspends
response
E6
SPF Shading Trouble
10 SPF shading error (Black level correction)
11 SPF shading error (White level correction)
14 SPF CCD-ASIC error
11 SPF shading error (White level correction)
14 SPF CCD-ASIC error
E7
MFP / HDD / LSU / PCU Control Trouble
01 MFP image data trouble.
03 HDD trouble.
04 HDD-ASIC error.
10 Shading trouble (Black level correction).
11 Shading trouble (White level correction).
14 CCD-ASIC communication error.
20 LSU laser detection error (K).
21 LSU laser detection error (C).
22 LSU laser detection error (M).
23 LSU laser detection error (Y).
24 LSU LD driver error (K)
25 LSU LD driver error (C)
26 LSU LD driver error (M)
27 LSU LD driver error (Y)
28 LSU-PCU connection trouble
29 LSU-ASIC frequency error
42 Image data trouble (ACRE-ASIC)
46 Image data decode error (ACRE-ASIC)
47 MFP & ACRE firmware inconsistency (ASIC)
48 Image data decode error (ACRE PWB)
49 Watermark data error
50 Firmware combination error (ICU – PCU)
55 PCU EEPROM sum check error
60 MFP combination error (Firmware/PWB)
61 MFP-PCU combination error
62 ICU connection error
80 MFP-SCU communication trouble.
90 MFP-PCU communication trouble.
91 Fax reception image data error
92 Copy image data error
93 Image data process error (except Copy &
03 HDD trouble.
04 HDD-ASIC error.
10 Shading trouble (Black level correction).
11 Shading trouble (White level correction).
14 CCD-ASIC communication error.
20 LSU laser detection error (K).
21 LSU laser detection error (C).
22 LSU laser detection error (M).
23 LSU laser detection error (Y).
24 LSU LD driver error (K)
25 LSU LD driver error (C)
26 LSU LD driver error (M)
27 LSU LD driver error (Y)
28 LSU-PCU connection trouble
29 LSU-ASIC frequency error
42 Image data trouble (ACRE-ASIC)
46 Image data decode error (ACRE-ASIC)
47 MFP & ACRE firmware inconsistency (ASIC)
48 Image data decode error (ACRE PWB)
49 Watermark data error
50 Firmware combination error (ICU – PCU)
55 PCU EEPROM sum check error
60 MFP combination error (Firmware/PWB)
61 MFP-PCU combination error
62 ICU connection error
80 MFP-SCU communication trouble.
90 MFP-PCU communication trouble.
91 Fax reception image data error
92 Copy image data error
93 Image data process error (except Copy &
Fax).
94 Image data process error (filing image data)
96 DIMM memory check error (MFP PWB)
99 LSU LD driver trouble
96 DIMM memory check error (MFP PWB)
99 LSU LD driver trouble
A0 LSU LD PWB EEPROM R/W error (K)
A1 LSU LD PWB EEPROM R/W error (C)
A2 LSU LD PWB EEPROM R/W error (M)
A3 LSU LD PWB EEPROM R/W error (Y)
A7 SSD trouble
A1 LSU LD PWB EEPROM R/W error (C)
A2 LSU LD PWB EEPROM R/W error (M)
A3 LSU LD PWB EEPROM R/W error (Y)
A7 SSD trouble
C0 TPM PWB (DSK) data access error
C1 DSK communication error (boot up)
C1 DSK communication error (boot up)
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N service manuals if exist.