Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man9) Service Manual ▷ View online
MX-4070N Dehumidifying heater 5 – 13
C. Heater kit installation
(1)
Heater unit assembly
1)
Attach the heater to the heater mounting plate and secure it with
the screw (M3 x 6 S-tight).
Attach the clamp, and fix the harness to the clamp.
the screw (M3 x 6 S-tight).
Attach the clamp, and fix the harness to the clamp.
The direction where the heater is attached to do the indication
side of voltage / electricity specifications listed in a heater in the
bottom.
side of voltage / electricity specifications listed in a heater in the
bottom.
2)
Attach the CSS-WH harness to the heater mounting plate, and
connect the harness of the dehumidifier heater.
connect the harness of the dehumidifier heater.
(2)
Heater unit attachment
1)
Remove the tray 1.
2)
Open the front cover. Attach the heater unit to the main unit, and
secure it with the screw (M4 x 10 P-tight).
secure it with the screw (M4 x 10 P-tight).
Pass the harness of the heater through the hole on the main unit
frame.
frame.
3)
Attach the wire saddle to the mein frame. Pass the CCS-WH har-
ness through the wire saddle. Connect the CCS-WH harness to
the AC-WH harness.
ness through the wire saddle. Connect the CCS-WH harness to
the AC-WH harness.
No.1
No.2
No.3
No.7
No.4
No.10
No.10
No.8
Ĭ
ĭ
No.5
ACWH harness
CSS-WH
harness
harness
2
: ‘16/Apr.
2
MX-4070N Dehumidifying heater 5 – 14
4)
Attach the High temperature caution label to the casette 1. (Only
200V series.)
200V series.)
(3)
External fixture attachment
1)
Close the front cover.
2)
Install the casette 1 to main body.
3)
Attach the rear cabinet.
D. Scanner heater kit installation
(1)
Scanner heater unit assembly
1)
Secure the marking position on the harness of the scanner heater
to the heater fixing plate with the banding band.
to the heater fixing plate with the banding band.
2)
Extend the harness, and secure the other position of it with band-
ing band.
ing band.
No.9
ĭ
ĭ
Ĭ
ĭ
ĭ
ĭ
ĭ
3
᳸OO
2
1
MX-4070N Dehumidifying heater 5 – 15
3)
Tighten the snap band and cut its tip to approx. 5 mm or less.
Slide the banding band head to the square hole (Part that is
enclosed by the mark).
enclosed by the mark).
The banding band head and cut tip must not protrude behind the
heater fixing plate.
heater fixing plate.
(2)
Table glass removal
1)
Open the SPF.
2)
Remove the glass holder. Remove the table glass and the SPF
glass.
glass.
(3)
Scanner heater unit attachment
1)
Attach the clamp to the scanner frame.
When installing, be careful to prevent damage of the wire.
DSPF type only
Ĭ
ĭ
Į
MX-4070N Dehumidifying heater 5 – 16
2)
Connect the harness of the scanner heater. Attach the scanner
heater unit, and fixing the screw (M3 x 4 Round-tipped).
heater unit, and fixing the screw (M3 x 4 Round-tipped).
3)
Attach the scanner heater and secure it with the screw (M4 x 6
Bind machine screw). Pass the harness through the clamp.
Bind machine screw). Pass the harness through the clamp.
The convex part of the scanner heater must be inserted into the
hole of the scanner frame.
hole of the scanner frame.
4)
Tighten the loose scanner heater harness by pulling it in the arrow
direction and secure it with the snap band then cut its tip to
approx. 5 mm or less.
direction and secure it with the snap band then cut its tip to
approx. 5 mm or less.
5)
Move the lamp unit by hand and check that it move smoothly in all
movable area.
movable area.
Check that there is no interference of the harness of the scanner
heater in the wire and the 2/3 mirror unit.
heater in the wire and the 2/3 mirror unit.
(4)
Table glass attachment
1)
Attach the SPF glass and the table glass. Attach the glass holder.
When installing the glass holder, slide it to the left until it clicks,
and fix it with screws.
and fix it with screws.
2)
Close the SPF.
2
2
1
1
2
DSPF type only
Ĭ
ĭ
Į
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man9) service manuals if exist.