Sharp MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man5) Handy Guide ▷ View online
Simulation Codes
33
Document Solutions After Sales Service
24
Data Counter Clear
1
Jam/trouble counter clear
2
Paper feed counter clear
3
Document feed & output counter clear
24
Data Counter Clear cont…..
4
Maintenance counter clear
5
Developer counter clear
6
Copy Counter clear
9
Print & other counter clear
10
Fax counter clear
15
Network scanner counter clear
25
Usage Estimator data display
35
Toner Cartridge Use Status data clear
25
DV Auto Adjustment / Monitor
1
Toner sensor output monitor (Process drive)
2
Auto developer adjustment setting
4
Operation data of toner supply quantity
5
Display toner correction data
26
Device Configuration
1
Right Tray setup
2
LCC setup
3
Auditor setup
5
A3 Total/Maintenance counter setup
6
Destination setup
7
Machine ID setup
10
Network scanner trial mode setup
18
Toner save operation
30
CE mark control setup
32
Specifications for fusing cleaning operation
35
Trouble memory mode setting
38
Engine life over setting (Developer)
41
Pamphlet mode AMS operation
49
Copy speed mode setup (Postcard)
50
Function setting (B/W reverse, colour mode,
finisher)
finisher)
51
Specifications for Serial Port operation (For PCI)
52
Blank paper count mode setting
53
Enable/Disable auto colour calibration
65
Finisher alarm set-up (stapled sheets)
69
Toner near end setting
71
Web browsing trial mode setup
73
Poster enlargement image loss adjustment
74
OSA trial mode set-up
78
Remote panel operation password setting
79
Enable/Disable user data delete result
30
Sensor Operation / Test
1
Main unit sensor check
2
Tray sensor check (main)
40
Bypass Operation / Adjustment
2
Bypass tray width adjustment
7
Bypass tray width detection manual setting
41
OSS Operation / Adjustment
1
Document sensor operation check
2
Document sensor output setup
3
Document sensor output display
43
Fuser Setting
1
Fuser temperature setup (Paper)
4
Fuser temperature. setup for each mode
20
Fuser temperature. correction for low
temperature & humidity
temperature & humidity
21
Fuser temp correction for high temperature &
humidity
humidity
22
Perform L/L correction for fuser temperature
setting
setting
23
Perform H/H correction for fuser temperature
setting
setting
24
Fuser temperature reset
31
Check operation of web cleaning (36 only)
32
Force web cleaning at job end (36 only)
44
Process Control
1
Process control mode setting
2
Process control Gain Adjustment
4
Process control initial density setup
6
Process control correction (force)
9
Process control data display
12
DM data, patch/base data display
13
Image density set-up (colour)
14
Fuser temp.& humidity output data
15
OPC drum idle rotation
21
Half tone process control registration
22
Half tone process control density patch result
24
Half tone correction data result display
25
Initial half tone correction data display
26
Half tone process control correction execution
27
Half tone process control correction data clear
28
Process control timing (On/Off) setting
29
Enable/disable half tone correction during each
job
job
31
OPC drum position adjustment
37
Image density correction setting
43
DV unit installation monitor
61
Set Calibration data of colour image density
sensor
sensor
62
Process control execution conditions
Simulation Codes
34
Document Solutions After Sales Service
46
Copy & Image Density Adjustment
1
Colour copy density adjustment
2
B/W copy density adjustment
4
Colour scanner density adjustment
5
B/W scanner density adjustment
8
Colour scanner balance adjustment
9
RSPF exposure adjustment
10
Engine colour balance manual adjustment
(Individual EXP)
(Individual EXP)
16
Engine balance manual adjustment B/W
19
B/W auto exposure mode setup
21
Engine colour balance manual adjustment (All
EXP)
EXP)
23
Engine maximum density adjustment
(enable/disable)
(enable/disable)
24
Engine half tone auto adjustment
25
Single colour mode colour balance set-up (copy)
26
Single colour mode colour balance adjustment
27
Coefficient (Black edge) gamma set-up
30
Sub scanning resolution adjustment
32
Document background density auto mode
36
2-colour mode adjustment (Red, Black)
37
B/W image create adjustment
38
Adjust black component colour mode
39
Fax Image send sharpness adjustment
40
Fax mode exposure adjust (All modes)
41
Fax mode exposure adjust (Normal)
42
Fax mode exposure adjust (Fine Text)
43
Fax mode exposure adjust (Super Fine)
44
Fax mode exposure adjust (Ultra Fine)
45
Fax mode exposure adjustment (600dpi)
46
Fax mode exposure adjustment (RGB Rip)
47
JPEG compression rate setting (Copy/Scanner –
Push scan)
Push scan)
51
Gama adjustment for copy in heavy paper mode
and image process mode
and image process mode
52
Copy calibration data clear
54
Engine colour balance adjust (Dither)
55
Drop out colour adjust (image send mode)
58
Copy mode pseudo resolution (smoothing
process)
process)
59
Copy mode pseudo resolution image process adj
60
Sharpness adjustment colour auto copy mode
61
Adjust area separation recognition level
62
Judgement level adjustment
63
Copy low density adjustment
65
Used to set the colour correction table
66
Adjust watermark reproduction capability
74
Copy/Printer colour balance adjustment
90
Process operation of high-compression PDF
images
images
91
Adjust reproduction of black text
48
Magnification & Motor Adjustment
1
Magnification ratio adjustment
5
Motor speed adjustment (Scanner & SPF)
6
Motor speed velocity adjustment
49
Firmware Update
1
Firmware Upgrade Program
3
E Manual Update Program
5
Watermark update
50
Image Position Adjustment
1
Lead edge/copy position adjustment
2
Lead edge/copy position adjustment value
(Calculation)
(Calculation)
5
Printer lead edge adjustment
6
RSPF Lead edge/copy position adjustment
7
RSPF Lead edge/copy position adjustment value
10
Print off-centre adjustment (K)
12
Original off-centre adjustment
20
Colour Image registration adjustment (Main
Scan)
Scan)
22
Auto colour registration & drum phase
adjustment
adjustment
24
Auto registration & drum data display
27
Image loss adjustment (Fax/Scanner mode)
28
Service adjustment (OC/SPF image position)
51
Resist Roller Adjustment
1
Transfer voltage ON/OFF timing adjustment
2
Resist roller adjustment
53
Document Feeder Adjustment
6
SPF document tray size adjustment
7
SPF document tray size adjust value set
8
RSPF scanning position adjustment
55
MFP Data Setting
1
Engine Control Operations (Soft SW)
2
Scanner Control Operations (Soft SW)
3
Controller Control Operations (Soft SW)
56
MFP Data Import / Export
1
Transfer data execute
2
EEPROM, SD Card & HDD backup to USB
3
Document filing backup to USB
4
Job log data backup to USB
5
Import SIM22-06 data to USB
11
Copy SD card data to HDD
12
Copy SD card data to HDD
Simulation Codes
35
Document Solutions After Sales Service
60
Memory Operation / Test
1
Check memory operation (read/write) of MFP
61
LSU Adjustment
1
LSU test (Polygon motor & Laser detection check)
3
Laser power setting
4
LSU image skew adjustment pattern
62
HDD Operation / Test
1
HDD and SD card format (FAT32)
2
HDD partial read/write check
3
HDD read/write check (All)
6
Smart (HDD) self diagnostics test (E7-03)
7
Smart (HDD) self diagnostics error log
8
HDD and SD card format (excluding system &
operation manual area)
operation manual area)
10
Used to delete the Job Log data
11
Used to delete the Document Filing data
12
Enable/Disable auto format for HDD trouble
13
HDD format (Operation Manual and Watermark
data area only)
data area only)
14
Delete document filing management data
15
Convert setting data for Doc filing reprint
20
Check operation of mirroring HDD
63
CCD Operation / Adjustment
1
Shading correction data display
2
Shading correction execution (force)
3
CCD gamma & colour balance auto adjustment
4
SIT chart patch density display
5
CCD gamma & colour balance setup (Default)
6
Print engine colour balance (chart reading)
7
Standard target colour calibration set-up
(Service)
(Service)
8
Standard scanner target default (Service Mode)
11
Colour Balance setting (Factory Mode).
64
Self Test Print
1
Self print test (Colour mode)
2
Engine colour balance patch print mode
4
Printer self print test (256 gradations)
5
Printer self print test (PCL)
6
Printer self pint test (PS)
7
Print adjustment pattern (SIM 46-21)
65
LCD Operation / Adjustment
1
LCD touch panel adjustment
2
LCD touch panel adjustment display
5
Operation panel key input check
66
Fax Operation / Adjustment
1
FAX Soft SW setting (2-99)
2
Country code default set (FAX)
3
FAX PWB controller memory check
4
FAX signal line check (Max level)
5
FAX signal line check (Soft SW setting)
6
FAX check list print (confidential registration)
7
FAX memory printout (all data)
8
FAX voice message setup
9
FAX signal (sound) line check (Soft SW setting)
10
FAX all memory clear
11
Voice signal check (line & speaker 300bps - Max)
12
Voice signal check (line & speaker 300bps SSW)
13
Register dial number for Sim 66-14/15/16
14
Adjust & check the time dial pulse (10bps)
15
Adjust & check the time dial pulse (20bps)
16
Adjust and check the send level DTFM signal
17
Select DTFM signal to send to line (Max level)
18
Select DTFM signal to send to line (Soft SW)
21
Print various registration information
22
Set the sound volume of the handset
24
Fast save data clear
29
FAX address book clear
30
Tel/LIU sensor status check
31
ON/OFF setting of each output port (Tel/LIU)
32
Received data check
33
Busy Tone/CNG/CED/FNET/DTMF detect signal
check
check
34
Communication time display
36
Check Send/Receive from modem controller
39
Check Destination saved in FAX EEPROM
42
Rewrite PIC program installed on FAX box
43
Write program & adjustment values to PIC
installed on FAX
installed on FAX
61
Display the FAX related soft SW (151-250)
62
Import FAX data to USB
67
Printer Board Operation / Adjustment
17
SRAM Clear / Reset
24
Printer colour balance auto adjustment
25
Printer colour balance manual adjustment
26
Standard target select of printer half tone auto
adjustment
adjustment
27
Scanner target of printer calibration setup
(Service)
(Service)
28
Standard target of printer colour calibration
(Service)
(Service)
31
Printer calibration data clear
33
Printer screen gamma adjustment
34
Engine maximum density adjustment
36
Printer low density adjustment
45
Adjust printer image filter and trapping
52
Printer Gamma default adjustment
54
Printer colour balance adjust
Trouble Codes
36
Document Solutions After Sales Service
A0
01
PCU ROM error
02
SCU ROM error
04
ACU/ACRE ROM error
05
ACU/ACRE Firmware error
10
Colour Profile error
11
Firmware Version Discrepancy (MFP-PCU)
14
MFP-CPU Firmware inconsistency
15
DSK Boot and program firmware error
16
Energy save data error (SD Card)
17
UI data & CPU firmware inconsistency
20
MFP Firmware & EPROM Discrepancy
21
PCU Firmware & EPROM Discrepancy
22
SCU Firmware & EPROM Discrepancy
C1
10
Main charger trouble (BK)
14
Main charger trouble (Colour)
C4
00
PTC trouble
CE
00
Network communication error
01
Network card is not installed or defective
02
FTP or mail server is not found
03
Specified server does not correspond during
transmission
transmission
04
Invalid account/password (FTP server)
05
Invalid directory entered (FTP server)
06
Specified mail server (POP3) is not found
07
Invalid server account or password
08
The specified mail server (POP3) suspends
response
response
01
02
03
04
07
02
03
04
07
MFP image data error
HDD trouble with mirroring kit
HDD trouble/mirroring kit error
HDD-ASIC error
SD Card error
HDD trouble with mirroring kit
HDD trouble/mirroring kit error
HDD-ASIC error
SD Card error
10
11
14
20
21
22
23
11
14
20
21
22
23
Shading trouble (Black level)
Shading trouble (White level)
CCD-ASIC error
LSU laser detection error (K)
LSU laser detection error (C)
LSU laser detection error (M)
LSU laser detection error (Y)
Shading trouble (White level)
CCD-ASIC error
LSU laser detection error (K)
LSU laser detection error (C)
LSU laser detection error (M)
LSU laser detection error (Y)
E7
24
LSU LD driver error (K)
25
LSU LD driver error (C)
26
LSU LD driver error (M)
27
LSU LD driver error (Y)
28
LSU-PCU connection error
29
LSU ASIC frequency error
42
Image data trouble (Scanner expansion PWB)
46
Data decode error (Scanner expansion PWB)
48
Scanner expansion PWB ASIC memory error
49
Watermark data error
50
PCU PWB Firmware detection error
55
PCU PWB information SUM error
60
MFP PWB Firmware detection error
61
Error between MFP & PCU PWB’s
65
MFP EEPROM sum check error
80
MFP-SCU PWB communication error
89
MFP CPU and NIC communication error
90
MFP-PCU PWB communication error
91
FAX reception image data error
92
Copy image data error
93
Copy, image send, filing, print image data
process error
process error
94
Image import file data process error
95
Printer PWB DIMM memory check error
96
MFP PWB DIMM memory check error
AO
LSU LD PWB EEPROM R/W error (K)
A1
LSU LD PWB EEPROM R/W error (C)
A2
LSU LD PWB EEPROM R/W error (M)
A3
LSU LD PWB EEPROM R/W error (Y)
EE
EC
Auto toner density adjustment error
EL
Auto toner density adjustment error
(Overtoned)
(Overtoned)
EU
Auto toner density adjustment error
(Undertoned)
(Undertoned)
F1
00
Finisher PCU communication error
03
Finisher exit roller lift operation trouble
08
Finisher staple shift motor trouble
10
Finisher staple motor trouble
11
Finisher grip motor trouble
15
Finisher paper exit tray lift motor trouble
19
Finisher paper alignment motor lock (front)
20
Finisher paper alignment motor lock (rear)
21
Finisher fan motor trouble (Bridging Unit)
31
Finisher saddle motor trouble
32
Communication error (finisher-punch unit)
33
Punch unit shift operation trouble.
E7
Click on the first or last page to see other MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man5) service manuals if exist.