DOWNLOAD Sharp MX-2310U / MX-3111U (serv.man17) Service Manual ↓ Size: 26.68 MB | Pages: 127 in PDF or view online for FREE

MX-3610N  MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER)  4 – 3

6)

Attach the connection cover included in the package.

1)

Pull out each tray. Turn and remove the fixing material, and
remove the caution sheet.
Attach the removed fixing material to the position shown in the
figure for storage.
Close the cassette which was pulled out.

Before turning on the power, check to insure that the fixing
material of the tray is disengaged. If the power is turned on
without disengaging the fixing material, a trouble may be
resulted.

1)

Remove the cover from the rear side of the machine.

2)

Connect the connector.

3)

Split the removed cover along the perforated line.

4)

Attach the cover.

1)

Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.

For setting the tray size, refer to “Tray size setup” (1-6).

MX-3610N  MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER)  4 – 4

The image lead edge position and the off-center adjustment value
of the desk unit have been set to the average value when shipping
from the factory. 
Therefore, this adjustment must be performed only when the judg-
ment is made to execute it through checking the print image.

1)

Enter the SIM50-28 mode.

2)

Select [SETUP/PRINT] ADJ with the key button.

3)

Select [ALL] with the key button.

By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
• [LEAD]: Print image lead edge image position adjustment
• [OFFSET]: Print image off-center adjustment

When [ALL] is selected, both of the above two items are
executed simultaneously.

4)

Select a paper feed tray to be adjusted.

5)

Press [EXECUTE] key.
The patch image (adjustment pattern) is printed out.

6)

Set the adjustment pattern on the document table.

Fit the adjustment pattern correctly with the document guide.
In this case, put 5 sheets of white paper on the printed adjust-
ment pattern.

7)

Press [EXECUTE] key.
The following item is automatically adjustment.
• Print image lead edge image position adjustment
• Print image off-center adjustment

8)

Press [OK] key.
The adjustment result becomes valid.

Perform procedures 4) to 7) for each paper feed tray.

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

2&ǂ$'-

%.0$*ǂ$'-

63)ǂ$'-

6(78335,17ǂ$'-

5(68/7

'$7$

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

/($'

2))6(7

$//

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

(;(&87(

0)7

&6

$'8

&6

&6

&6

/&&

MX-3610N  MX-KB11 (KEYBOARD)  5 – 1

MX-3610N

Service Manual

 

Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.

1)

Remove the front cabinet upper.

2)

Remove the operation panel cover.

3)

Remove the operation panel upper cover.

1)

Slide the operation panel unit to the left, and put it down.
Remove the operation panel cover.

2)

Remove the operation panel lower cover.

1

Keyboard unit

1

2

Operation panel lower cover (For keyboard)

1

3

Fixing screw (M4 x 8 S-tight)

3

2

3

1

MX-3610N  MX-KB11 (KEYBOARD)  5 – 2

3)

Turn over the operation panel unit.

4)

Remove the clamp. Peel off the mylar and disconnect the con-
nector.

1)

Turn over the operation section cover.

2)

Attach the keyboard unit and fix it with the fixing screw.

3)

Connect the keyboard interface harness and attach the opera-
tion section cover.

Be sure to place the key interface harness between the opera-
tion section cover and the FFC. (Section A)

1)

Connect the connector to the operation panel unit , and fix the
harness with the clamp.

When assembling, put the mylar on the flat cable and fix them
with the clamp.