Sharp MX-2310U / MX-3111U (serv.man17) Service Manual ▷ View online
MX-3610N Dehumidifying heater 3 – 13
2)
Remove the connector cover.
3)
Attach the edge saddle. Attach the heater harness 2, and pass
it through the edge saddle.
Pass the earth wire through the edge saddle, and fix it with a
screw (M4 x 8).
it through the edge saddle.
Pass the earth wire through the edge saddle, and fix it with a
screw (M4 x 8).
4)
Attach the connector cover.
5)
Attach the mounting plate.
6)
Attach the clamp to the 1CS drive unit.
Pass the heater harness 2 through the clamp, and attach the
snap band to the 2CS drive unit.
Connect the heater harness and the heater harness 2.
Pass the heater harness 2 through the clamp, and attach the
snap band to the 2CS drive unit.
Connect the heater harness and the heater harness 2.
(6) Paper feed tray removal
1)
Pull out the paper feed tray, and lift it to remove.
(7) Tray 2 heater unit attachment
1)
Pass the harness of the heater unit for the tray 2 through the
hole in the frame. Attach the heater unit for the tray 2 to the
frame, and fix it with a screw (M3 x 6).
hole in the frame. Attach the heater unit for the tray 2 to the
frame, and fix it with a screw (M3 x 6).
2
1
1
3
2
1
2
2
2
2
1
2
1
MX-3610N Dehumidifying heater 3 – 14
2)
Attach the clamp to the frame. Connect the harness of the
heater unit for the tray 2 to the heater harness, and pass it
through the clamp.
heater unit for the tray 2 to the heater harness, and pass it
through the clamp.
3)
Attach the high temperature caution label to the paper feed
tray 2.
tray 2.
(8) Tray 3/4 heater unit attachment
1)
Pass the harness of the heater unit for the tray 3/4 through the
hole in the frame. Attach the heater unit for the tray 2 to the
frame, and fix it with a screw (M3 x 6).
hole in the frame. Attach the heater unit for the tray 2 to the
frame, and fix it with a screw (M3 x 6).
2)
Attach the clamp to the frame. Connect the harness of the
heater unit for the tray 3/4 to the frame, and pass it through the
clamp.
heater unit for the tray 3/4 to the frame, and pass it through the
clamp.
3)
Attach the high temperature caution label to the frame.
(9) Connector connection
1)
Remove the rear cabinet cover of the machine.
2)
Connect the heater harness to the machine harness.
1
2
2
2
2
1
1
2
MX-3610N Dehumidifying heater 3 – 15
3)
Attach the rear cabinet cover of the machine.
(10) Right rear cabinet and rear cabinet attachment
1)
Attach the right rear cabinet and the rear cabinet.
(11) Paper feed tray attachment
1)
Attach the paper feed tray.
E. LCC heater kit installation
(1) Paper feed unit removal
1)
Pull out the paper feed tray.
2)
Open the upper cover.
3)
Remove the upper cabinet.
4)
Disconnect the connector, and remove the paper feed unit.
2
1
3
3
3
3
2
1
1
1
2
2
3
1
2
1
2
1
MX-3610N Dehumidifying heater 3 – 16
(2) Heater cover and cabinet removal
1)
Remove the heater cover.
2)
Remove the cabinet.
(3) Heater attachment
1)
Attach the heater.
2)
Attach the protect sheet.
(4) Heater harness unit attachment
1)
Attach the snap band of the heater harness unit. While holding
the harness upward, attach the AC cord fixer.
the harness upward, attach the AC cord fixer.
After attaching the snap band, cut and trim the end of the
band.
band.
Be careful not to mistake the attaching direction of the AC cord
fixer.
fixer.
1
2
1
2
2
1
75
˴5mm
r
0
˴
2mm
㨪
2
1
Click on the first or last page to see other MX-2310U / MX-3111U (serv.man17) service manuals if exist.