Sharp AR-M700 (serv.man27) Service Manual ▷ View online
AR-M550/M620/M700 SIMULATION 8 - 69
(Table 2)
(Table 3)
Operation/Procedure
(Lead edge image loss adjustment) (Table 1)
1) Set the front and back surface image loss adjustment values
(LEAD EDGE) as specified below:
(Standard set value) Lead edge image loss: 1.5mm (LEAD: 1.5)
Paper lead edge: 3.5mm (DENA: 35)
Paper lead edge: 3.5mm (DENA: 35)
∗
Set the adjustment value of LEAD to 15. (Enter 15 as the adjust-
ment value of LEAD EDGE, and press [P] key.)
ment value of LEAD EDGE, and press [P] key.)
2) Make a duplex copy at 100% with the SPF, and check that the lead
edge (image loss) is 1.5mm either on the front surface and the
back surface. (Select the duplex mode in the paper selection mode
of SIM 50-6.) (Table 3) (Enter 100 as the copy magnification ratio
set value (MAGNIFICATION), and press [START] key.)
back surface. (Select the duplex mode in the paper selection mode
of SIM 50-6.) (Table 3) (Enter 100 as the copy magnification ratio
set value (MAGNIFICATION), and press [START] key.)
If the adjustment result is not satisfactory, perform the following proce-
dures:
dures:
3) Change the adjustment values of SIDE1 and SIDE2, and perform
the adjustment. (Change the adjustment values of SIDE1 and
SIDE2, and press [START] key.)
SIDE2, and press [START] key.)
(Shift for the adjustment value change: 0.1mm/step)
(The image scan start timing is determined with the detection tim-
ing of the document lead edge by the detector SPPD4.)
ing of the document lead edge by the detector SPPD4.)
Repeat procedures 2) and 3) until a satisfactory result is obtained.
(Rear edge image loss adjustment)
1) Use the SPF at 100% to make a duplex copy, and check that the
rear edge image loss is 1.5mm on the front and the back surfaces.
(Select the duplex mode in the paper selection mode of SIM 50-6.)
(Enter 100 as the copy magnification ratio set value (MAGNIFICA-
TION), and press [START] key.)
(Select the duplex mode in the paper selection mode of SIM 50-6.)
(Enter 100 as the copy magnification ratio set value (MAGNIFICA-
TION), and press [START] key.)
If the adjustment value is not satisfactory, , perform the following pro-
cedure.
cedure.
2) Change the adjustment value of TRAIL EDGE. Change the adjust-
ment value of TRAIL EDGE, and press [START] key.
Repeat the above procedures until a satisfactory result is obtained.
(Front/rear frame direction image loss adjustment)
Set the adjustment value of the front surface and the back surface
(FRONT/REAR) to 20. (Enter 20 as the adjustment value of FRONT/
REAR, and press [P] key.)
(FRONT/REAR) to 20. (Enter 20 as the adjustment value of FRONT/
REAR, and press [P] key.)
When the adjustment value is changed, the image position is shifted in
the front/rear frame direction.
the front/rear frame direction.
NOTE: When [P] key is pressed after entering the adjustment value,
the adjustment value is set. When [START] key is pressed
instead, the adjustment value is set and copying is performed.
(Table 2)
instead, the adjustment value is set and copying is performed.
(Table 2)
(Copy condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key. (Table 3)
4) Press [START] key. (The paper feed tray is selected.)
∗
To set the copy magnification ratio, perform the following procedure.
(Void set value)
17 LEAD_EDGE
(DENA)
Lead edge void set
value
value
0 - 99
35
18 TRAIL_EDGE
(DENB)
Rear edge void
adjustment value
adjustment value
19 FRONT/
REAR
Front/Rear void
adjustment value
adjustment value
20 SIDE2 ADJ.
RRCB correction
value in the back
surface print mode
value in the back
surface print mode
1 - 99
50
Normal display
NOW PRINTING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
6
LCC
Side LCC
Select 0, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
Item
Set
range
Default
AR-M550N/U,
AR-620N/U
AR-
M700N/U
50
2
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. NOW PRINTING.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
2.RRCB
Select 1,
and press
[START] key.
and press
[START] key.
Select other than 0 - 1, and press [START] key.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START.
0.TRAY SELECT
LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START.
0.TRAY SELECT
1
1.PRINT START
(ADJUSTMENT DATA)
LEAD EDGE: 2.RRCB
LEAD EDGE: 2.RRCB
50
20.SIDE2 ADJ.
50
RESIST: 3.T1
50
4.T2
50
5.T3
50
6.T4
50
7.BPT
50
8.LCC
50
9.ADU
50
OFF CENTER: 10.T1
50
11.T2
50
12.T3
50
13.T4
50
14.BPT
50
15.LCC
50
16.ADU
50
(VOID SETTING) 17.LEAD_EDGE(DENA)
50
18.TRAIL_EDGE(DENB)
30
19.FRONT/REAR
30
1
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 1-16, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
50-6
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the copy image position and void area
(image loss) on print paper in the copy mode. (The
similar adjustment can be performed with SIM 50-7
(simple method).) (SPF mode)
(image loss) on print paper in the copy mode. (The
similar adjustment can be performed with SIM 50-7
(simple method).) (SPF mode)
Section
Item
Picture quality
SIDE1: SPF front surface document lead edge scan position
adjustment value
SIDE2: SPF back surface document lead edge scan position
adjustment value
AR-M550/M620/M700 SIMULATION 8 - 70
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
(Table 1)
(Table 2)
(Table 3)
When the total of the above set value and 10 is entered, the mode is
changed to the duplex mode (DD), and a duplex copy is made.
changed to the duplex mode (DD), and a duplex copy is made.
Operation/Procedure
(Lead edge image loss adjustment)
1) Set the front and back surface image loss adjustment values
(LEAD EDGE) as specified below:
(Standard set value) Lead edge image loss: 1.5mm (LEAD: 1.5)
Paper lead edge void: 3.5mm (DENA: 35)
Paper lead edge void: 3.5mm (DENA: 35)
∗
Set the adjustment value of LEAD to 15. (Enter 15 as the adjust-
ment value of LEAD EDGE, and press [P] key.)
ment value of LEAD EDGE, and press [P] key.)
2) Set the adjustment value of L4 to 0. (Enter 0 as the adjustment
value of L4, and press [P] key.
3) Set the adjustment value of L5 to 0. (Enter 0 as the adjustment
value of L5, and press [P] key.
4) Make a copy at 200% with the SPF, and calculate the values of L4
and L5. (Enter 200 as the set value of the copy magnification ratio
set value (MAGNIFICATION) and press [START] key.)
set value (MAGNIFICATION) and press [START] key.)
Set range
25 - 200 (%)
Item
Set
range
Default
0
TRAY SELECT
Paper feed tray selection
1 - 6
–
1
COPY START
Copy START (Default)
–
–
2
MAGNIFICATION Print magnification ratio
25 -
200%
–
(Lead edge adjustment value)
3
SIDE1
Front surface document
scan start position
adjustment value
scan start position
adjustment value
0 - 99
50
4
SIDE2
Back surface document
scan start position
adjustment value
scan start position
adjustment value
(Image loss set value: SIDE 1)
5
LEAD_EDGE
Front surface lead edge
image loss set value
image loss set value
0 - 99
15
6
FRONT_REAR
Front surface side edge
image loss set value
image loss set value
20
7
TRAIL_EDGE
Front surface rear edge
image loss set value
image loss set value
0 - 20
0
(Image loss set value: SIDE 2)
8
LEAD_EDGE
Back surface lead edge
image loss set value
image loss set value
0 - 99
15
9
FRONT/REAR
Back surface side edge
image loss set value
image loss set value
20
10 TRAIL_EDGE
Back surface rear edge
image loss set value
image loss set value
0 - 20
0
Normal display
NOW COPYING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
6
LCC
Side LCC
Select 2, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
50-7
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the copy image position and void area
(image loss) on print paper in the copy mode. (The
similar adjustment can be performed with SIM 50-6.)
(SPF mode)
(image loss) on print paper in the copy mode. (The
similar adjustment can be performed with SIM 50-6.)
(SPF mode)
Section
Item
Picture quality
L4 = Distance (mm) from the image lead edge position to the
scale of 10mm x 10
50
1
2
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
100
(ADJUSTMENT DATA)3.SIDE1
50
4.SIDE2
50
(IMAGE LOSS SETTING)
SIDE1: 5.LEAD_EDGE
15
6.FRONT/REAR
20
7.TRAIL_EDGE
0
SIDE2: 8.LEAD_EDGE
15
9.FRONT/REAR
20
10.TRAIL_EDGE
0
Press [CUSTOM SETTING] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). INPUT VALUE 0-99, AND PRESS
START.
3.SIDE1
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). NOW COPYING.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
Select 1,
and press
[START] key.
and press
[START] key.
Select 0, and press [START] key.
Select other than 0 - 2, and press [START] key.
100
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF).
(MAGNIFICATION)
INPUT 25-200(%)
AR-M550/M620/M700 SIMULATION 8 - 71
5) Enter the above values as the set values of L4 and L5. (Enter the
adjustment values of L4 and L5, and press [P] key.)
(The image scan start timing is determined with the detection tim-
ing of the document lead edge by the detector SPPD4.)
ing of the document lead edge by the detector SPPD4.)
If the adjustment result is not satisfactory, perform the above proce-
dures again or adjust with SIM 50-1.
dures again or adjust with SIM 50-1.
NOTE: If the adjustment result of the above procedures is not satisfac-
tory, though the adjustment value is changed individually, the
adjustment cannot be completed normally.
adjustment cannot be completed normally.
Repeat procedures 2) - 6) until a satisfactory result is obtained.
(Rear edge image loss adjustment)
Adjust so that the rear edge image loss is 3.5mm. (Change the adjust-
ment value of TRAIL EDGE, and press [START] key.)
ment value of TRAIL EDGE, and press [START] key.)
(Front/rear frame direction image loss adjustment)
Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment
value of SIDE, and press [P] key.)
value of SIDE, and press [P] key.)
When the adjustment value is changed, the image position is shifted in
the front/rear frame direction.
the front/rear frame direction.
NOTE: When [P] key is pressed after entering the adjustment value,
the adjustment value is set. When [START] key is pressed
instead, the adjustment value is set and copying is performed.
(Table 2)
instead, the adjustment value is set and copying is performed.
(Table 2)
(Copy condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key. (Table 3)
4) Press [START] key. (The paper feed tray is selected.)
∗
To set the copy magnification ratio, perform the following procedure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
(Table 1)
(Table 2)
(Table 3)
When the total of the above set value and 10 is entered, the mode is
changed to the duplex mode (DD), and a duplex copy is made.
changed to the duplex mode (DD), and a duplex copy is made.
L5 = Distance (mm) from the image lead edge position to the
paper lead edge x 10
Set range
25 - 200 (%)
Item
Set
range
Default
0
TRAY SELECT
Paper feed tray selection
(1 - 6)
(1 - 6)
–
–
1
COPY START
Copy START (Default)
–
–
2
MAGNIFICATION Print magnification ratio
(25 - 200%)
–
–
(Lead edge adjustment value)
3
L4
Distance from the front
surface image lead edge
to the scale of 10mm
(SPF: 200%)
surface image lead edge
to the scale of 10mm
(SPF: 200%)
0 - 999
–
4
L5
Distance from the back
surface image lead edge
to the scale of 10mm
(SPF: 200%)
surface image lead edge
to the scale of 10mm
(SPF: 200%)
–
(Image loss set value: SIDE 1)
5
LEAD_EDGE
Front surface lead edge
image loss set value
image loss set value
0 - 99
15
6
FRONT_REAR
Front surface side edge
image loss set value
image loss set value
20
7
TRAIL_EDGE
Front surface rear edge
image loss set value
image loss set value
0 - 20
0
(Image loss set value: SIDE 2)
8
LEAD_EDGE
Back surface lead edge
image loss set value
image loss set value
0 - 99
15
9
FRONT/REAR
Back surface side edge
image loss set value
image loss set value
20
10 TRAIL_EDGE
Back surface rear edge
image loss set value
image loss set value
0 - 20
0
Normal display
NOW COPYING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
6
LCC
Side LCC
Select 2, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
Item
Set
range
Default
50
1
2
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
200
(ADJUSTMENT DATA) 3.L4
160
4.L5
160
(IMAGE LOSS SETTING)
SIDE1: 5.LEAD_EDGE
15
6.FRONT/REAR
20
7.TRAIL_EDGE
0
SIDE2: 8.LEAD_EDGE
15
9.FRONT/REAR
20
10.TRAIL_EDGE
0
Press [CUSTOM SETTING] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-99, AND
PRESS START.
3.L4
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
Select 1,
and press
[START] key.
and press
[START] key.
Select 0, and press [START] key.
Select other than 0 - 2, and press [START] key.
100
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.).
(MAGNIFICATION)
INPUT 25-200(%)
AR-M550/M620/M700 SIMULATION 8 - 72
Operation/Procedure
(Print image off-center position adjustment)
NOTE: This simulation cannot provide an accurate adjustment. Do not
use.
1) Enter the number corresponding to the number of the paper feed
tray to be adjusted with 10-key. (Select one of 3 - 9.)
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [P] key or [START] key. When [START] key is pressed, the
adjustment value set and copying is performed.
(Image off-center adjustment)
1) Enter 1 with 10-key.
2) Press [START] key. The adjustment pattern is printed.
3) Check the off-center of the printed image.
(UNIT: 0.1mm/step When the adjustment value is increased, the
print image is shifted to the front direction.)
print image is shifted to the front direction.)
NOTE: This adjustment can be performed with SIM 50-5.
(Copy condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key. (Select one of 1 - 6)
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value and 10 is entered, the mode is
changed to the duplex print mode.
changed to the duplex print mode.
∗
To set the copy magnification ratio, perform the following procedure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
NOTE: When [P] key is pressed after entering the adjustment value in
this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.
is pressed, the adjustment value is set and copying is per-
formed.
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the scan mode to be adjusted
with 10-key. (Select one of 3 - 5.)
2) Press [START] key.
50-10
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the print image off-center position.
(Adjusted separately for each paper feed section.)
(Adjusted separately for each paper feed section.)
Section
Item
Picture quality
Image position
Item
Set range Default
0 TRAY SELECT
Paper feed tray selection
1 - 6
–
1 COPY START
Copy START (Default)
–
–
2 MAGNIFICATION Print magnification ratio
25 - 400%
100
(Off-center adjustment value)
3 TRAY1
Tray 1 adjustment
0 - 99
50
4 TRAY2
Tray 2 adjustment
5 TRAY3
Tray 3 adjustment
6 TRAY4
Tray 4 adjustment
7 BPT
Manual feed tray
adjustment
adjustment
8 LCC
Side LCC adjustment
9 ADU
Adjustment when paper is
fed again from ADU
fed again from ADU
Normal display
NOW COPYING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
6
LCC
Side LCC
Set range
25 - 400 (%)
Select 0, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
50-12
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the scan image off-center position.
(Adjusted separately for each scan mode.)
(Adjusted separately for each scan mode.)
Section
Item
Picture quality
Image position
Item
Set range
Default
0 TRAY SELECT
Paper feed tray
selection
selection
1 - 5
–
1 COPY START
Copy START (Default)
–
–
2 MAGNIFICATION Print magnification ratio
25 - 400%
100
(Resist adjustment value)
3 PLATEN
OC mode adjustment
0 - 99
50
4 SPF SIDE1
SPF front surface
adjustment
adjustment
5 SPF SIDE2
SPF back surface
adjustment
adjustment
50
2
Select 1,
and press
[START] key.
and press
[START] key.
Select other than 0 - 2, and
press [START] key.
press [START] key.
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
100
(ADJUSTMENT DATA)
3.TRAY1
50
4.TRAY2
50
5.TRAY3
50
6.TRAY4
50
7.BPT
50
8.LCC
50
9. ADU
50
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND
PRESS START.
2.TRAY1
1
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
Click on the first or last page to see other AR-M700 (serv.man27) service manuals if exist.