DOWNLOAD Sharp AR-M550 (serv.man15) Service Manual ↓ Size: 905.4 KB | Pages: 98 in PDF or view online for FREE

AR-M550/M620  SIMULATION  8 - 25

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press [START] key.

The load selected in procedure 1 turns ON for 10sec.

Press [CUSTOM SETTINGS] key to stop the operation.

The copy lamp or CIS is turned on for 10sec and turned off.

NOTE: CIS: only when the DSPF is installed.

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press [START] key. 

The load selected in procedure 1 turns ON for 30sec.

Press [CUSTOM SETTINGS] key to stop the operation.

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press [START] key.

The load selected in procedure 1 operates.

Press [CUSTOM SETTINGS] key to stop the operation.

5-3

Operation test/Check

Used to check the operation of the scanner lamp and 
the control circuit.

Optical (Image scanning)

Operation

Press [START] key, and the operation is 
started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped after 10sec.

5-4

Operation test/Check

Used to check the operation of the discharge lamp and 
the related circuit.

Process

Operation

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped after 30sec.

SIMULATION 5-3

COPY LAMP TEST. SELECT 1-2, AND PRESS START.

1.COPY LAMP

2.CIS

1

SIMULATION 5-3

COPY LAMP TEST. EXECUTING···.

1.COPY LAMP

2.CIS

1

SIMULATION 5-4

DISCHARGE LAMP CHECK. SELECT 1, AND PRESS START.

1.DL

1

SIMULATION 5-4

DISCHARGE LAMP CHECK. SELECT 1, AND PRESS START.

1.DL

1

6-1

Operation test/Check

Used to check the operation of the paper transport 
system loads and the control circuit.

Paper transport (Discharge/Switchback/Transport)

Operation

1

MSWPR

MSW reset signal

2

HLPR

Heater power relay signal

3

DCPR

DC power relay signal

4

MM

Main motor

5

DM

Drum motor

6

DVM

Developing motor

7

TURM

Transfer separation motor

8

TRM

PS front motor

9

POM1

Paper exit motor 1

10

POM2_FW

Paper exit motor 2 forward rotation

11

POM2_RV

Paper exit motor 2 reverse rotation

12

VPM

Paper transport motor

13

RRC

Resist roller clutch signal

14

PSBC

Brake clutch signal 

15

PSPS

Separation pawl

16

T1PFC

Tray 1 paper feed clutch

17

T2PFC

Tray 2 paper feed clutch 

18

HPFC

Horizontal transport clutch 

19

T1PUS

Tray 1 pickup solenoid

20

T2PUS

Tray 2 pickup solenoid

21

HPLS

Relay path clock solenoid

22

T1LUM

Tray 1 lift-up motor 

23

T2LUM

Tray 2 lift-up motor

24

DSKPFC1

Desk paper transport clutch upstream side

25

DSKPFC2

Desk paper transport clutch downstream side

26

M1PFC

Tray 3 paper feed clutch 

27

M2PFC

Tray 4 paper feed clutch

28

M1PUS

Tray 3 pickup solenoid

29

M2PUS

Tray 4 pickup solenoid

30

M1LUM

Tray 3 lift-up motor

31

M2LUM

Tray 4 lift-up motor

32

TRC_LCC

Desk clutch sync signal 

33

FUM

Fusing motor

34

MPFPUS

Manual pickup solenoid

35

MPFC

Manual paper feed clutch signal

36

MPFGS

Manual gate solenoid

AR-M550/M620  SIMULATION  8 - 26

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press [START] key.

The load selected in procedure 1 operates.

Press [CUSTOM SETTINGS] key to stop the operation.

*

All fans: All the fans controlled by the engine.
(Exhaust fan motor, heat exhaust fan motor (paper exit upper),
cooling fan motor (right side) cooling fan motor (power source),
cooling fan motor (developing), cooling fan motor (ADU))

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press [START] key.

The transfer belt performs contact/separation with the OPC drum.

Press [CUSTOM SETTINGS] key to stop the operation.

NOTE: Before disassembling the transfer unit, use this simulation to

separate the transfer unit from the OPC drum.

1) Select the number corresponding to the operating condition of

aging with 10-key.

The combined mode of 0 - 6 mode and 10, 20, or 30 mode can be
set.

In that case, the number corresponding to one of 0 - 6 mode and
the number corresponding to one of 10, 10, and 30 mode are
added and the sum number is entered.

2) Press [START] key.

The condition selected in procedure 1) is set.

The setting of this simulation is kept valid until the power is turned off.

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped immediately or after 
repeating the operation several times.

6-2

Operation test/Check

Used to check the operations of each fan motor and its 
control circuit.

Other

Operation

1

VFM-EX

Paper exit fan motor

2

CFM-UP 

Heat exhaust fan motor (Paper exit upper)

3

CFM-R 

Cooling fan motor (Right side)

4

CFM-DC

Cooling fan motor (Power source)

5

CFM-DV

Cooling fan motor (Developing)

6

CFM-ICU /HDD

Cooling fan motor (Controller/HDD)

7

ALL

All fans control*

8

CFM-AD

Cooling fan motor (ADU)

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped.

SIMULATION 6-1

FEED OUTPUT CHECK. SELECT 1- 33, AND PRESS START.

1.MSWPR  2.HLPR  3.DCPR  4.MM   5.DM

6.DVM    7.TURM  8.TRM   9.POM1

10.POM2_FW   11.POM2_RV   12.VPM

13.RRC    14.PSBC   15.PSPS   16.T1PFC

17.T2PFC  18.HPFC   19.T1PUS  20.T2PUS

21.HPLS   22.T1LUM  23.T2LUM  24.DSKPFC1

25.DSKPFC2  26.M1PFC  27.M2PFC  28.M1PUS

29.M2PUS    30.M1LUM  31.M2LUM  32.TRC_LCC

33.FUM      34.MPFPUS 35.MPFC   36.MPFGS

    2

SIMULATION 6-1

FEED OUTPUT CHECK. EXECUTING···.

1.MSWPR  2.HLPR  3.DCPR  4.MM   5.DM

6.DVM    7.TURM  8.TRM   9.POM1

10.POM2_FW  11.POM2_RV  12.VPM

13.RRC    14.PSBC   15.PSPS   16.T1PFC

17.T2PFC  18.HFC    19.T1PUS  20.T2PUS

21.HPLS   22.T1LUM  23.T2LUM  24.DSKPFC1

25.DSKPFC2  26.M1PFC  27.M2PFC  28.M1PUS

29.M2PUS    30.M1LUM  31.M2LUM  32.TRC_LCC

33.FUM      34.MPFPUS 35.MPFC   36.MPFGS

    2

SIMULATION 6-2

FAN MOTOR CHECK. SELECT 1-8, CAND PRESS START.
1. VFM-EX   2. CFM-UP 
3. CFM-R    4. CFM-DC
5. CFM-DV   6. CFM-ICU /HDD
7. ALL      8. CFM-AD 

    2

SIMULATION 6-2

FAN MOTOR CHECK..
2. CFM-UP 

  2

6-3

Operation test/Check

Used to check the operations of the transfer unit and 
the related circuit. 

Process (Transfer)

1

TURM (RELEASE)

Transfer unit separation state

2

TURM (JOINT)

Transfer unit contact state

Press [START] key, and the operation is 
started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped immediately or after 
repeating the operation several times.

After completion 

Press [CUSTOM SETTINGS] key to stop the 
operation.

7-1

Setting

Used to set the operating conditions of aging.

Operation

0

NO MISS FEED DETECTION

No jam detection

1

AGING

Aging mode

2

AGING/NO MISS FEED 
DETECTION.

No jam detection, aging 
mode

SIMULATION 6-3

TURM CHECK. SELECT 1-2 CAND PRESS START.
1. TURM(RELEASE)
2. TURM(JOINT)

    2

SIMULATION 6-3

TURM CHECK. EXECUTING...
1. TURM(RELEASE)

  2

SIMULATION 6-3

TURM CHECK.

COMPLETE....

1. TURM(RELEASE

  2

AR-M550/M620  SIMULATION  8 - 27

1) Enter the intermittent aging cycle (unit: sec) with 10-key.

2) Press [START] key.

The time entered in procedure 1) is set.

∗

Set range of interval time: 1 - 999 (sec)

Set the intermittent aging mode cycle of 7-1 with 10-key. (Unit: sec)

1) Select the number corresponding to the warm-up time display

YES/NO.

2) Press [START] key, and the number selected in procedure 1) is

set.

∗

The setting of this simulation is kept valid until the power is turned
off.

The warm-up time is displayed in the unit of second.

1) Enter the number corresponding to the adjustment item with 10-

key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key.

(The set value is stored, and the output corresponding to the set
value is outputted for 30sec.)

Press [CUSTOM SETTINGS] key to stop the operation.

(The developing bias output voltage adjustment and output check can
be made in each print mode.)

3

AGING/NO MISS FEED 
DETECTION/NO WARM UP/
NO TEMPERATURE 
CONTROL.

No jam detection/ no warm-
up/ no fusing temperature 
control, aging mode

4

NO WARM UP.

No warm-up 

5

AGING/INTERVAL.

Intermittent aging mode

6

AGING/INTERVAL/NO MISS 
FEED DETECTION.

No jam detection 
intermittent aging mode

+10

NO PROCESS UNIT CHECK.

Above +10: No process unit 
(including the developing 
unit) detection

+20

NO SHADING.

Above +20: No shading

+30

NO PROCESS UNIT CHECK/
NO SHADING.

Above +30: No process unit 
detection /no shading

Press [START] key to start registration and operation. 
The operation mode is kept until the power is turned off or setting is made again. 

7-6

Setting

Used to set the intermittent aging cycle.

Operation

7-8

Setting

Used to set the warm-up time display YES/NO.

Operation

SIMULATION 7-1

AGING TEST SETTING. SELECT 0-36, AND PRESS START.

0.NO MISS FEED DETECTION

1.AGING

2.AGING/NO MISS FEED DETECTION.

3.AGING/NO MISS FEED DETECTION/

  NO WARM UP/NO TEMPERATURE CONTROL.

4.NO WARM UP.

5.AGING/INTERVAL.

6.AGING/INTERVAL/NO MISS FEED DETECTION.

+10:NO PROCESS UNIT CHECK.

+20:NO SHADING.

+30:NO PROCESS UNIT CHECK/NO SHADING.

    2

SIMULATION 7-6

INTERVAL AGING CYCLE SETUP. INPUT TIME AND PRESS START.

(1-999, UNIT: sec)

10

Warm-up is completed.

Press [CUSTOM SETTINGS] key.

8-1

Adjustment/Operation test/Check

Used to check and adjust the operations of the 
developing voltage of each color and the control circuit.

Image process (Photoconductor/Developing/Transfer/
Cleaning)

Item

Set range

Default

1

AUTO

Auto mode

0 - 750

495

2

CHARACTER

Text mode

3

MIX

Text/Photo mode

4

PHOTO

Photo mode

5

PRINTER

Printer mode

6

FAX

FAX mode

7

PLUS

Reverse developing
bias voltage

0 - 250

150

SIMULATION 7-8

WARM UP TIME DISPLAY. 

ARE YOU SURE?

1. YES

2. NO

1

Press [START] key, 
and time count is started.

SIMULATION 7-8

WARM UP TIME DISPLAY. WARMING UP,PLEASE WAIT.

(UNIT:sec)

 30 

Press [CUSTOME SETTING] key, 
and time count is stopped.

SIMULATION 7-8

WARM UP TIME DISPLAY. WARM UP COMPLETED.

(UNIT:sec)

 60 

AR-M550/M620  SIMULATION  8 - 28

1) Enter the number corresponding to the adjustment item with 10-

key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key.

(The set value is stored, and the output corresponding to the set
value is outputted for 30sec.)

Press [CUSTOM SETTINGS] key to stop the operation.

(The main charger grid output voltage adjustment and output check
can be made in each print mode.)

1) Enter the number corresponding to the adjustment item with 10-

key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key.

(The set value is stored, and the voltage corresponding to the set
value is outputted for 30sec.)

Press [CUSTOM SETTINGS] key to stop the operation.

(The transfer output voltage adjustment and output check can be made
in each print mode.)

Press [START] key.

Press [CUSTOM SETTINGS] key. 

Press [START] key.

Press [CUSTOM SETTINGS] key. 
Or after 30sec output.

8-2

Adjustment/Operation test/Check

Used to check and adjust the operation of the main 
charger grid voltage in each printer mode and the 
control circuit.

Image process (Photoconductor/Developing/Transfer/
Cleaning)

Item

Set range

Default

1

AUTO

Auto mode

200 - 1000

580

2

CHARACTER

Text mode

3

MIX

Text/Photo mode

4

PHOTO

Photo mode

5

PRINTER

Printer mode

6

FAX

FAX mode

SIMULATION 8-1

1

DV BIAS SETTING. SELECT 1-7, AND PRESS START.

1.AUTO 

495

  2.CHARACTER 

495

3.MIX 

495

   4.PHOTO 

495

5.PRINTER 

495

  6.FAX 

495

  7.PLUS 

150

SIMULATION 8-1

DV BIAS SETTING. INPUT VALUE, AND PRESS START.

1:AUTO (0-750)

495

SIMULATION 8-1

DV BIAS SETTING. EXECUTING···.

1:AUTO

495

Press [START] key.

Press [CUSTOM SETTINGS] key. 

Press [START] key.

Press [CUSTOM SETTINGS] key. 
Or after 30sec output.

8-6

Adjustment/Operation test/Check

Used to check and adjust the operation of the transfer 
charger voltage and the control circuit.

Image process (Photoconductor/Developing/Transfer/
Cleaning)/Transfer

Item

Set range

Default

1

FRONT

Long side print mode

0 - 800

350

2

BACK

Back side print mode

350

Press [START] key.

Press [CUSTOM SETTINGS] key. 

Press [START] key.

Press [CUSTOM SETTINGS] key. 
Or after 30sec output.

SIMULATION 8-2

1

MAIN GRID SETTING. SELECT 1-6, AND PRESS START.

1.AUTO 

580

  2.CHARACTER 

580

3.MIX 

580

   4.PHOTO 

580

5.PRINTER 

580

  6.FAX 

580

SIMULATION 8-2

MAIN GRID SETTING. INPUT VALUE, AND PRESS START.

1.AUTO (200-1000)

580

SIMULATION 8-2

MAIN GRID SETTING. EXECUTING···.

1.AUTO

580

SIMULATION 8-6

1

THV+ SETTING. SELECT 1-2, AND PRESS START.

1.FRONT 

350

2.BACK 

350

SIMULATION 8-6

THV+ SETTING. INPUT VALUE, AND PRESS START.

1.FRONT(0-800)

350

SIMULATION 8-6

THV+ SETTING. EXECUTING···.

1.FRONT

350