Sharp AR-M550 (serv.man15) Service Manual ▷ View online
AR-M550/M620 SIMULATION 8 - 21
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press START key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
Operation/Procedure
The operating conditions of the sensors and detectors are displayed.
The active sensors and detectors are highlighted.
2-3
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the loads in the
automatic document feeder unit and the control
circuits.
automatic document feeder unit and the control
circuits.
Section
DSPF
Item
Operation
1
MOTOR (T)
Motor top speed
2
MOTOR (H)
Motor high speed
3
MOTOR (L)
Motor low speed
4
STRBC
Document transport brake clutch
5
STRC
Document feed transport clutch
6
SPFC
Document fed clutch
7
SRRC
Document resist clutch
8
SRRBC
Document resist brake clutch
9
STRRC
Document feed resist clutch
10
STRRBC
Document feed resist brake clutch
11
STMPS
Stamp solenoid
12
SLUM
Lift up motor
13
SPFFAN
SPF fan motor
Press [START] key, and the
operation is started.
operation is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
operation is stopped.
SIMULATION 2-2
SPF SENSOR CHECK.
SSET
SOCD
SCOV
SPED2
SPED1 SPPD1 SPPD2 SPPD3
SPPD4 SPOD
SWD6
SWD5
SWD4 SWD3 SWD2 SWD1
SPLS2 SPLS1
CISSET
STSET
STUD STLD
SWD_LEN:
2100
SWD_AD:
600
SIMULATION 2-3
SPF LOAD TEST. SELECT 1-13, AND PRESS START.
1.MOTOR(T) 2.MOTOR(H) 3.MOTOR(L)
4.STRBC 5.STRC 6.SPFC 7.SRRC
8.SRRBC 9.STRRC 10.STRRBC 11.STMPS
12.SLUM 13.SPFFAN
2
SIMULATION 2-3
SPF LOAD TEST. EXECUTING···.
1.MOTOR(T) 2.MOTOR(H) 3.MOTOR(L)
4.STRBC 5.STRC 6.SPFC 7.SRRC
8.SRRBC 9.STRRC 10.STRRBC 11.STMPS
12.SLUM 13.SPFFAN
2
3
3-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of sensor and detector in
the finisher and the related circuit.
the finisher and the related circuit.
Section
Finisher
Item
Operation
PI1
Entry port paper detection
PI1P
Punch width resist HP detection
When the punch unit is
installed
installed
PI1S
Paper holding plate motor clock
detection
detection
When the saddle unit is
installed
installed
PI2P
Punch motor clock detection
When the punch unit is
installed
installed
PI2S
Front door open detection
When the saddle unit is
installed
installed
PI3
Paper exit detection
PI3P
Punch HP detection
When the punch unit is
installed
installed
PI3S
Paper exit cover open detection
When the saddle unit is
installed
installed
PI4S
Paper folding motor clock
detection
detection
When the saddle unit is
installed
installed
PI5
Shutter open detection
PI5S
Alignment plate HP detection
When the saddle unit is
installed
installed
PI6
Alignment guide HP detection
PI6S
Saddle tray paper detection
When the saddle unit is
installed
installed
PI7
Staple shift HP detection
PI7S
Paper positioning plate HP
detection
detection
When the saddle unit is
installed
installed
PI8
Tray 1 HP detection
PI8S
Paper positioning plate HP
detection
detection
When the saddle unit is
installed
installed
PI9
Tray 1 lift motor clock detection 1
PI9S
Entry port cover open detection
When the saddle unit is
installed
installed
PI10
Paper exit motor clock detection
PI11
Tray 1 paper detection
PI11S
Saddle paper exit detection
When the saddle unit is
installed
installed
PI12
Tray 2 paper detection
PI12S
Semi-circular roller phase
detection
detection
When the saddle unit is
installed
installed
PI13S
Guide HP detection
When the saddle unit is
installed
installed
PI14
Buffer path detection
PI14S
Paper holding plate lead edge
position detection
position detection
When the saddle unit is
installed
installed
PI15
Finisher joint detection
PI15S
Paper holding plate lead edge
position detection
position detection
When the saddle unit is
installed
installed
PI16
Door open detection
PI17
Buffer path entry port paper
detection
detection
PI17S
Vertical path paper detection
When the saddle unit is
installed
installed
PI18
Oscillating guide open detection
PI18S
Saddle No. 1 paper detection
When the saddle unit is
installed
installed
AR-M550/M620 SIMULATION 8 - 22
( ) : Added when the punch unit is installed.
< > : Added when the saddle unit is installed.
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press START key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
(When the punch unit is installed)
(When the saddle unit is installed.)
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key. (The entered value is stored.)
PI19
Tray lift motor clock detection 2
PI19S
Saddle No. 2 paper detection
When the saddle unit is
installed
installed
PI20
Oscillation guide clock detection
PI20S
Saddle No. 3 paper detection
When the saddle unit is
installed
installed
PI21
Staple lead edge detection
PI21S
Paper folding HP detection
When the saddle unit is
installed
installed
PI22
Staple dive HP detection
PI23
Tray 2 lift motor clock detection 1
PI24
Tray 2 lift motor clock detection 2
PI25
Tray 2 HP detection
MS1
Front door / Upper door open
detection
detection
MS1S
Saddle entry port door detection
When the saddle unit is
installed
installed
MS2
Oscillation guide close detection
MS2P
Punch front door open detection
When the punch unit is
installed
installed
MS2S
Front door open detection
When the saddle unit is
installed
installed
MS3
Safety area detection
MS3S
Paper exit door open detection
When the saddle unit is
installed
installed
MS4
Shutter close detection
MS4S
Saddle staple presence detection
2
2
When the saddle unit is
installed
installed
MS5S
Stitch operation HP detection 2
When the saddle unit is
installed
installed
MS6S
Saddle staple presence detection
1
1
When the saddle unit is
installed
installed
MS7
Cartridge detection
MS7S
Stitch operation HP detection 1
When the saddle unit is
installed
installed
MS8
Staple empty detection
MS9
Tray approaching detection
3-3
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of the load in the finisher
and the control circuit.
and the control circuit.
Section
Finisher
Item
Operation
1
SL7
Belt wait solenoid
2
SL6
Wait solenoid
SIMULATION 3-2
FINISHER SENSOR CHECK.
PI10 PI20 PI19 PI9 PI22
PI1
PI14 PI3
PI17 PI12 PI11
MS8
PI21 MS7
PI18
PI5
PI8 PI6 PI7 MS2 MS4 MS1 MS3 PI16
PI15 MS9 PI24 PI23 PI25
(PI2P) (MS2P) (PI1P) (PI3P)
<PI11S><PI15S><PI5S> <PI14S><PI1S> <PI4S> <PI13S>
<PI12S><PI17S><PI7S> <PI18S><PI6S> <PI8S><MS7S>
<MS5S><PI20S><PI19S><PI21S><MS3S><PI9S> <PI2S>
<PI3S> <MS2S><MS1S><MS6S><MS4S>
3
SL5
Paddle solenoid
4
SL3
Buffer exit port solenoid
5
SL2
Buffer entry port solenoid
6
SL1
Flapper solenoid
7
M10
Tray 2 lift motor
8
M9
Entry port transport motor
9
M8
No. 2 transport motor
10
M7
Oscillation motor
11
M6
Staple motor
12
M5
Tray 1 lift motor
13
M4
Stapler shift motor
14
M3
Alignment motor
15
M2
Paper exit motor
16
M1
No. 1 transport motor
17
M2P
Punch side resist motor
18
M1P
Punch motor
19
SL4S
Transport plate contact solenoid
20
SL2S
No. 2 paper deflection plate solenoid
21
SL1S
No. 1 paper deflection plate solenoid
22
M8S
Paper holding motor
23
M7S
Stitch motor: Front
24
M6S
Stitch motor: Rear
25
M5S
Saddle alignment motor
26
M4S
Paper positioning motor
27
M3S
Guide motor
28
M2S
Paper folding motor
29
M1S
Saddle transport motor
Press [START] key, and the operation
is started.
is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
operation is stopped.
3-10
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Finisher (AR-F16) adjustment
Section
Finisher
Item
Operation
Item
Set range
1
Saddle stitch/folding position
adjustment
adjustment
192 - 208, 1STEP: 0.25 mm
2
Alignment position adjustment
2 - 18, 1STEP: 0.35 mm
3
Staple binding position
adjustment
adjustment
68 - 132, 1STEP: 0.152 mm
4
Punch center adjustment
37 - 63, 1STEP: 0.15mm
SIMULATION 3-3
FINISHER LOAD TEST. SELECT 1-
AND PRESS START.
2
SIMULATION 3-3
FINISHER LOAD TEST. EXECUTING
.
2
AR-M550/M620 SIMULATION 8 - 23
Operation/Procedure
The operating conditions of the sensors and detectors are displayed.
The active sensors and detectors are highlighted.
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press [START] key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
Operation/Procedure
1) Select the number corresponding to the adjustment item with 10-
key.
2) Press [START] key.
3) Enter the setting (adjustment) value with 10-key.
4) Press [START] key.
5
Punch hole position adjustment
(Paper feed direction)
(Paper feed direction)
35 - 57, 1STEP: 0.26mm
6
Stack tray standby position
adjustment (Small size)
adjustment (Small size)
5 - 35, 1STEP: 1mm
7
Stack tray standby position
adjustment (Large size)
adjustment (Large size)
5 - 35, 1STEP: 1mm
Press [START] key, and the operation
is started.
is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
operation is stopped.
3-30
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the sensors and
detectors in the inserter.
detectors in the inserter.
Section
Inserter
Item
TH_SEN
Sub tray pull-out detection
TS_SEN
Sub tray storage detection
T_SEN
Inserter tray paper size detection
EMP_SEN
Inserter tray empty detection
REG_SEN
Inserter resist sensor
TIM_SEN
Inserter timing sensor detection
JCK_SEN
Inserter cover open/close sensor
H_SEN
Inserter reverse sensor
HI_SEN
Inserter paper exit sensor
HYK_SEN
Inserter reverse unit open/close sensor
S_SW
Inserter set SW
KC_SEN
Base cover open/close sensor
P_ST_SW
Inserter start SW
P_MO_SW
Inserter staple mode select SW
P_PN_SW
Inserter punch select SW
Item
Set range
SIMULATION 3-10
FINISHER SETTING. SELECT 1-7 AND PRESS START.
1. SADDLE POSITION
2. ALIGNMENT POSITION
3. STAPLE POSITION
4. PUNCH CENTER
5. PUNCH HOLE
6. TRAY WAITING POSITION(S-SIZE)
7. TRAY WAITING POSITION(L-SIZE)
FINISHER SETTING. SELECT 1-7 AND PRESS START.
1. SADDLE POSITION
2. ALIGNMENT POSITION
3. STAPLE POSITION
4. PUNCH CENTER
5. PUNCH HOLE
6. TRAY WAITING POSITION(S-SIZE)
7. TRAY WAITING POSITION(L-SIZE)
1
SIMULATION 3-10
CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START.
1. SADDLE POSITION
200
SIMULATION 3-30
INSERTER SENSOR CHECK.
TH_SEN TS_SEN T_SEN EMP_SEN
REG_SEN TIM_SEN JCK_SEN H_SEN
HI_SEN HYK_SEN S_SW KC_SEN
P_ST_SW P_MO_SW P_PN_SW
INSERTER SENSOR CHECK.
TH_SEN TS_SEN T_SEN EMP_SEN
REG_SEN TIM_SEN JCK_SEN H_SEN
HI_SEN HYK_SEN S_SW KC_SEN
P_ST_SW P_MO_SW P_PN_SW
3-31
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the loads in the
inserter and the related circuits.
inserter and the related circuits.
Section
Inserter
Item
Operation
1
K_MOT
Reverse motor
2
Y_MOT
Horizontal transport motor
3
H_MOT
Inserter reverse
4
F_SOL
Inserter flapper solenoid
5
R_CL
Inserter resist clutch
6
P_LED
Inserter operation panel upper LED
Press [START] key, and the operation
is started.
is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
operation is stopped.
3-32
Purpose
Setting (Adjustment)
Function
(Purpose)
(Purpose)
Inserter paper width detection level setting.
Section
Inserter
Item
Operation
1
MAX. POSITION
Max. position
2
POSITION 1
Adjustment point 1
3
POSITION 2
Adjustment point 2
4
MIN. POSITION
Min. width
Press [START] key.
Press [CUSTOM SETTINGS] key.
SIMULATION 3-31
INSERTER LOAD TEST. SELECT 1-6, AND PRESS START.
1. K_MOT 2. Y_MOT 3. H_MOT
4. F_SOL 5. R_CL 6. P_LED
INSERTER LOAD TEST. SELECT 1-6, AND PRESS START.
1. K_MOT 2. Y_MOT 3. H_MOT
4. F_SOL 5. R_CL 6. P_LED
2
SIMULATION 3-31
INSERTER LOAD TEST. EXECUTING....
2. Y_MOT
2
1
SIMULATION 3-32
INSERTER TRAY VALUE SETTING. SELECT 1-4, AND PRESS
START.
1. MAX. POSITION :
INSERTER TRAY VALUE SETTING. SELECT 1-4, AND PRESS
START.
1. MAX. POSITION :
72
2. POSITION 1 :
380
3. POSITION 2 :
710
4. MIN. POSITION :
804
SIMULATION 3-32
INSERTER TRAY VALUE SETTING. INPUT VALUE 0-1023, AND
PRESS START.
1. MAX. POSITION
INSERTER TRAY VALUE SETTING. INPUT VALUE 0-1023, AND
PRESS START.
1. MAX. POSITION
72
AR-M550/M620 SIMULATION 8 - 24
Operation/Procedure
The operating conditions of the sensors and detectors are displayed.
The active sensors and detectors are highlighted.
<LCC>
Operation/Procedure
1.
Select the number corresponding to the target of operation check
with 10-key.
with 10-key.
2.
Press [START] key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
<Side LCC>
Operation/Procedure
The LCD is changed as shown below. (The contrast changes every
2sec from the current level to MAX
2sec from the current level to MAX
→
MIN
→
the current level. During
this period, each LED is lighted.
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press [START] key.
The load selected in procedure 1 performs ON/OFF operation.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
The ON/OFF operation of the selected heater lamp is repeated
every 500ms five times.
every 500ms five times.
4
4-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the sensors and
detectors in the paper feed section (large capacity tray)
and the related circuit.
detectors in the paper feed section (large capacity tray)
and the related circuit.
Section
Paper feed
Item
Operation
LTD
Transport sensor
LUD
Tray upper limit sensor
LLD
Tray lower limit sensor
LPED
Tray paper presence/empty sensor
LTOD
Main unit connection detection sensor
LCD
Tray insertion detection
LOSW
Upper open/close detection SW
LRE
Lift motor encoder sensor
+24VM
24V power monitor
LLSW
Upper limit SW
4-3
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the loads in the paper
feed section (large capacity tray) and the related
circuit.
feed section (large capacity tray) and the related
circuit.
Section
Paper feed
Item
Operation
1
LTM
LCC transport motor
2
LLM
LCC lift motor
3
LPFCL
Paper feed clutch
4
LPSL
LCC paper feed clutch
5
LTCL
LCC transport clutch
6
LTLSL
Tray lock solenoid D
Press [START] key, and the operation
is started.
is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
operation is stopped.
SIMULATION 4-2
LCC SENSOR CHECK.
LTD LUD LLD LPED
LCD LOSW LRE +24VM
LLSW
LCC SENSOR CHECK.
LTD LUD LLD LPED
LCD LOSW LRE +24VM
LLSW
SIMULATION 4-3
LCC LOAD TEST. SELECT 1-6, AND PRESS START.
1.LTM 2.LLM
3.LPFCL 4.LPSL
5.LTCL 6.LTLSL
2
SIMULATION 4-3
LCC LOAD TEST. EXECUTING....
1. LTM 2. LLM
3. LPFCL 4. LPSL
5. LTCL 6. LTLSL
2
5
5-1
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of the display, LCD in the
operation panel, and control circuit.
operation panel, and control circuit.
Section
Operation (Display/Operation key)
Item
Operation
After 6.0sec
Press [CUSTOM SETTINGS] key,
and the operation is stopped.
and the operation is stopped.
5-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of the heater lamp and the
control circuit.
control circuit.
Section
Fixing (Fusing)
Item
Operation
1
HL1 (LOWER)
Heater lamp 1 (Lower)
2
HL2 (UPPER)
Heater lamp 2 (Upper)
3
HL3 (LEFT)
Heater lamp 3 (Left)
Press [START] key, and the operation
is started.
is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
The operation is repeated the specified
number of times before stopping.
operation is stopped.
The operation is repeated the specified
number of times before stopping.
SIMULATION 5-1
SIMULATION 5-1
SIMULATION 5-2
HEATER LAMP TEST. SELECT 1-3 ,AND PRESS START.
1.HL1(LOWER)
2.HL2(UPPER)
3.HL3(LEFT)
2
SIMULATION 5-2
HEATER LAMP TEST. EXECUTING···.
1.HL1(LOWER)
2.HL2(UPPER)
3.HL3(LEFT)
2
Click on the first or last page to see other AR-M550 (serv.man15) service manuals if exist.