Sharp AR-M351U / AR-M451U (serv.man16) Service Manual ▷ View online
AR-M351U/M451U, AR-M355U/M455U ADJUSTMENTS 8 - 13
H. Image density adjustment
The image density adjustment is required for the following copy
quality mode by using the simulation.
quality mode by using the simulation.
There are two methods; the collective adjustment and the individ-
ual adjustment of the copy quality mode.
ual adjustment of the copy quality mode.
• Copy mode
• FAX mode
(1) Copy mode
a. Test chart setting
1) Place a test chart (UKOG-0162FCZZ) on the original table as
shown below.
2) Place several sheets of A3 (11 x 17) white paper
(Sharp’s specified paper) on the test chart at the rear refer-
ence.
ence.
Test chart comparison
b. Density adjustment procedure
<1> Collective adjustment of two or more copy quality modes
Normally this adjustment is performed with SIM 46-2. In this
method, two or more copy density adjustments in different modes
can be adjusted collectively.
method, two or more copy density adjustments in different modes
can be adjusted collectively.
1) Execute SIM 46-2.
(Binary value mode)
Copy quality mode Collective
Adjustment
Individual
adjustment
Binary
value
mode
value
mode
Auto mode
SIM46-2
Character mode
SIM46-9
Character/Photo mode
SIM46-10
Photo mode
SIM46-11
Adjustment
Individual
adjustment
Normal
mode
mode
Binary value
mode
mode
AUTO
SIM46-12
SIM46-13
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
Small text
mode
mode
Binary value
mode
mode
AUTO
SIM46-14
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
Half tone
mode
mode
AUTO
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
Fine mode
Binary value
mode
mode
AUTO
SIM46-15
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
Half tone
mode
mode
AUTO
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
Super fine
mode
mode
Binary value
mode
mode
AUTO
SIM46-16
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
Half tone
mode
mode
AUTO
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
600dpi
mode
mode
Binary value
mode
mode
AUTO
SIM46-45
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
Half tone
mode
mode
AUTO
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
EXP1.0
EXP2.0
EXP3.0
EXP4.0
EXP5.0
UKOG-
0162FCZZ
DENSITY No.
0162FCZZ
DENSITY No.
1
2
3
4
5
6
7
8
9
10 W
UKOG-
0089CSZZ
DENSITY No.
0089CSZZ
DENSITY No.
0.1
0.2
0.3
0.5 1.9
0
KODAK GRAY
SCALE
SCALE
1
2
3
4
19
A
SHARP
CORPORATION
MADE IN JAPAN
CORPORATION
MADE IN JAPAN
Quality mode
Linked simulation data
AE3.0 (AE)
CH3.0 (Character)
SIM46-9
MIX3.0 (Character/Photo)
SIM46-10
PH3.0 (Photo)
SIM46-11
UKOG-0162FCZZ
1
10
W
2
3
4
5
6
7
8
9
AR-M351U/M451U, AR-M355U/M455U ADJUSTMENTS 8 - 14
2) Press the COPY button to make a copy.
Check that the copy density is as shown in the table below.
If not, change the adjustment value.
<2> Individual adjustment of each copy quality mode
This adjustment is used when a different density level for different
copy quality mode is required. SIM 46-5 to -7 and SIM 46-9 to -11
are used.
copy quality mode is required. SIM 46-5 to -7 and SIM 46-9 to -11
are used.
1) Execute the simulation corresponding to the copy quality
mode to be adjusted.
2) Press the COPY button to make a copy
Check that the copy density is as shown in the table below. If not,
change the adjustment value.
change the adjustment value.
For the auto mode, there is only one adjustment value. For the
other modes, the adjustment value for each density level must be
adjusted.
other modes, the adjustment value for each density level must be
adjusted.
(2) Adjusting the print quality in fax mode
This adjustment is needed in the following situations:
• The CCD unit has been replaced.
• U2 trouble has occurred.
• The MFP control PWB has been replaced.
• The EEPROM on the MFP control PWB has been replaced.
• The scanner control PWB has been replaced.
• The EEPROM on the scanner control PWB has been replaced.
• One or more parts of the scanner (reading) section have been
replaced.
Select 2, and press [START] key.
Press [START] key,
or press [CUSTOM SETTINGS] key.
or press [CUSTOM SETTINGS] key.
SIMULATION 46-2
Select other then 0 - 2, and
press [START] key.
press [START] key.
Press [CUSTOM SETTINGS] key.
SIMULATION 46-2
EXP. LEVEL SETUP (2). INPUT VALUE 0-99, AND PRESS START.
3. AE 3.0
Press [START] key.
SIMULATION 46-2
EXP. LEVEL SETUP (2). NOW COPYING.
50
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
SIMULATION 46-2
EXP. LEVEL SETUP (2). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
1
Select 0, and
press [START] key.
press [START] key.
1
Select 1,
and press
[START] key.
and press
[START] key.
EXP. LEVEL SETUP (2). SELECT 0-6, AND PRESS START.
0. TRAY SELECT
1
1. COPY START
2. EXP LEVEL
1
3. AE 3.0
50
4. CH 3.0
50
5. MIX 3.0
50
6. PHOTO 3.0
50
SIMULATION 46-2
EXP. LEVEL SETUP (2). SELECT 3-6, AND PRESS START.
(EXP. LEVEL SELECT)
3. AE 3.0 4. CH 3.0
5. MIX 3.0 6. PHOTO 3.0
1
• Adjustment spec
If the copy density is too light, increase the adjustment value.
If the copy density is too dark, decrease the adjustment value.
Adjustment range: 30 - 170
Mode
EXP.
Chart
No.
Adjustment
level
Chart
No.
Adjustment
level
Character
3
3
Copied
2
Not copied
Character/
Photo
Photo
3
3
Copied
2
Not copied
Photo
3
3
Copied
2
Not copied
Auto
3
Copied
2
Not copied
Select 2, and press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
SIMULATION 46-9
Select other than 0 - 2, and
press [START] key.
press [START] key.
Press
[CUSTOM SETTINGS] key.
[CUSTOM SETTINGS] key.
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). INPUT VALUE 0-99, AND PRESS
START.
3. 1.0
Press [START] key.
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). NOW COPYING.
50
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
1
Select 0, and
press [START] key.
press [START] key.
1
Select 1,
and press
[START] key.
and press
[START] key.
EXP. LEVEL SETUP (CHAR.2). SELECT 0-11, AND PRESS START.
0. TRAY SELECT
1
1. COPY START
2. EXP LEVEL
1
3. 1.0
50
4. 1.5
50
5. 2.0
50
6. 2.5
50
7. 3.0
50
8. 3.5
50
9. 4.0
50
10. 4.5
50
11. 5.0
50
SIMULATION 46-9
EXP. LEVEL SETUP (CHAR.2). SELECT 3-11, AND PRESS START.
(EXP. LEVEL SELECT)
3. 1.0 4. 1.5 5. 2.0
6. 2.5 7. 3.0 8. 3.5
9. 4.0 10. 4.5 11. 5.0
1
AR-M351U/M451U, AR-M355U/M455U ADJUSTMENTS 8 - 15
(Fax mode image density adjustment items)
(Fax mode density)
The print density settings should be normally left at defaults but
should be adjusted according to user requests, if any.
should be adjusted according to user requests, if any.
a. Adjust the fax mode print density for all modes at once
1) Set the test chart (UKOG-0162FCZZ) on the original table so
that it aligns with the front frame. Then put four or five pieces
of A3 (11" x 17") paper .
of A3 (11" x 17") paper .
2) Go through the modes specified in Simulation 46-12.
3) Select the adjustment item (FAX EXP. LEVEL) using the
numeric keypad.
4) Press the Start key.
5) Press the Start key (A copy is created.)
Check the print density.
If the print density is not at an acceptable level, do the follow-
ing steps.
ing steps.
6) Enter the print adjustment value using the numeric keypad.
7) Press the P or Start key
This applies the adjustment value.
Pressing the Start key starts print operation as well as apply-
ing the adjustment value.
ing the adjustment value.
8) Check the print density.
Repeat steps 6 to 8 until an acceptable print density is obtained.
Note: Adjusting the Fax print density through this simulation
changes the print density settings for all Fax modes to the
density level applied by carrying out this simulation.
The Fax mode print density settings for individual Fax
modes adjusted through Simulations 46-13, -14, -15, -16
and -45 are changed to the print density level applied by
this simulation.
density level applied by carrying out this simulation.
The Fax mode print density settings for individual Fax
modes adjusted through Simulations 46-13, -14, -15, -16
and -45 are changed to the print density level applied by
this simulation.
Image mode
Simulation for
adjustment
All-mode
adjustment
Individual-
mode
adjustment
Fax mode
print density
adjustment
(standard
mode)
print density
adjustment
(standard
mode)
Auto
mode
mode
Binary mode
46-12
46-13
Manual Binary mode
Fax mode
print density
adjustment
(small-
character
mode)
print density
adjustment
(small-
character
mode)
Auto
mode
mode
Binary mode
46-14
Half tone
mode
mode
Manual Binary mode
Half tone
mode
mode
Fax mode
print density
adjustment
(fine mode)
print density
adjustment
(fine mode)
Auto
mode
mode
Binary mode
46-15
Half tone
mode
mode
Manual Binary mode
Half tone
mode
mode
Fax mode
print density
adjustment
(super fine
mode)
print density
adjustment
(super fine
mode)
Auto
mode
mode
Binary mode
46-16
Half tone
mode
mode
Manual Binary mode
Half tone
mode
mode
Fax mode
print density
adjustment
(600dpi
mode)
print density
adjustment
(600dpi
mode)
Auto
mode
mode
Binary mode
46-45
Half tone
mode
mode
Manual Binary mode
Half tone
mode
mode
00
Select 0, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
Item
Set
range
Default
0
TRAY SELECT
Paper feed tray selection
1
COPY START
Copy START (Default)
2
FAX EXP. LEVEL FAX mode print density
0 - 99
50
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET). SELECT 0-2, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.FAX EXP.LEVEL
50
Press [CUSTOM SETTINGS] key.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET), INPUT VALUE 0-99, AND
PRESS START.
2.FAX EXP.LEVEL
50
1
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET). NOW PRINTING.
Select 1, and
press [START] key.
press [START] key.
Select other than 0 - 1, and
press [START] key.
press [START] key.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET).SELECT 1-5, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
AR-M351U/M451U, AR-M355U/M455U ADJUSTMENTS 8 - 16
b. Adjust the fax mode print density (standard mode/
small-character mode/super fine mode/600dpi mode)
This adjustment is intended to the print mode for each Fax mode
individually. In manual mode, the print density setting for each
print density adjustment level (1 to 5) can be adjusted to a custom
density level.
individually. In manual mode, the print density setting for each
print density adjustment level (1 to 5) can be adjusted to a custom
density level.
1) Set the test chart (UKOG-0162FCZZ) on the original table so
that it aligns with the front frame. Then put four or five pieces
of A3 (11" x 17") paper .
of A3 (11" x 17") paper .
2) Go through the simulation modes that correspond to the Fax
modes for which to adjust the print density (i.e., the modes
specified in Simulations 46-13, -14, -15, -16, or -45).
specified in Simulations 46-13, -14, -15, -16, or -45).
Select 2, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
00
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS
START.
0.TRAY SELECT
1
1.PRINT START
2.EXP LEVEL
1
3.AUTO
50
4.1.0
50
5.2.0
50
6.3.0
50
7.4.0
50
8.5.0
50
50
1
1
Select 1,
and press
[START] key.
and press
[START] key.
Select 0, and press [START] key.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL),INPUT VALUE 0-99, AND
PRESS START.
4.1.0
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). NOW PRINTING.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 1-5, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
(ABOVE +20:DSPF MODE)
Select other than 0 - 2,
and press [START] key. Press [CUSTOM SETTINGS] key.
and press [START] key. Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
1
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0 5.2.0
6.3.0 7.4.0 8.5.0
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection
1 PRINT START Print start (Default)
2 EXP LEVEL
Exposure level selection
3 AUTO
Auto
0 - 99
50
4 1.0
Exposure level 1
5 2.0
Exposure level 2
6 3.0
Exposure level 3
7 4.0
Exposure level 4
8 5.0
Exposure level 5
Select 2, and
press [START] key.
press [START] key.
Press [START] key or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
50
1
1
Select 1,
and press
[START] key.
and press
[START] key.
Select other than 0 - 2,
and press [START] key.
and press [START] key.
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START.
0.TRAY SELECT
1
1.PRINT START
2.EXP LEVEL
1
3.AUTO
50
4.1.0
50
5.2.0
50
6.3.0
50
7.4.0
50
8.5.0
50
9.AUTO(H)
50
10.1.0(H)
50
11.2.0(H)
50
12.3.0(H)
50
13.4.0(H)
50
14.5.0(H)
50
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE),INPUT VALUE 0-99, AND PRESS
START.
4.1.0
Select 0, and press [START] key.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE). NOW PRINTING.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
Press [START] key,
or press [CUSTOM SETTINGS] key.
or press [CUSTOM SETTINGS] key.
1
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE). SELECT 3-14, AND PRESS START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0 5.2.0
6.3.0 7.4.0 8.5.0
9.AUTO(H) 10.1.0(H) 11.2.0(H)
12.3.0(H) 13.4.0(H) 14.5.0(H)
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man16) service manuals if exist.