DOWNLOAD Sharp AR-M316 (serv.man18) Service Manual ↓ Size: 1.4 MB | Pages: 24 in PDF or view online for FREE

The "OPERATION SETTINGS" are related to basic 
operation of the machine and consist of the following 
programs:

● AUTO CLEAR SETTING

● MESSAGE TIME SETTING

● KEYS TOUCH SOUND

● TOUCH KEY OPERATION SETTING

● DISABLE INTERRUPT PRINT JOB

● STREAM FEEDING MODE

● DISPLAY LANGUAGE SETTING

● DISABLE DISPLAY TIMEOUT

● DISABLING OF TRAY SETTINGS

● DISABLING OF CLOCK ADJUSTMENT

If no action is taken for a certain length of time when 
viewing information on finished jobs, jobs in progress, 
or stored jobs, the auto clear function activates and 
returns the display to the initial screen of copy mode or 
the job status screen. AUTO CLEAR SETTING is used 
to set the amount of time that must elapse for the auto 
clear function to activate. The time can be set from 10 
seconds to 240 seconds in increments of 10 seconds, 
or the auto clear function can be disabled. (This setting 
only operates in copy mode and network scanner 
mode.)
The factory default setting is "60" (sec.).

This program is used to set the length of time that 
messages appear in the display (this applies to 
messages that appear for a certain length of time and 
then automatically disappear.) 
The time can be set to as long as 12 seconds in 
increments of one second.
The factory default setting is "6" (sec.).

This program is used to select whether or not a beep is 
sounded when a key is touched, and if sounded, what 
type of beep.
The program is also use to select whether or not a 
special key touch beep is sounded at the initial point of 
a setting.
The factory default settings are as follows:

• KEYS TOUCH SOUND: Short
• KEYS TOUCH SOUND AT INITIAL POINT: Disabled

 key .... Touch this key to select a short beep 

volume. A single short beep indicates a 
valid key, and a double short beep indicates 
an invalid key.

 key .... Touch this key to select a long beep 

volume. A single long beep indicates a valid 
key, and a double long beep indicates an 
invalid key.

 key .... Touch this key to disable key touch beeps.

Select the [KEYS TOUCH SOUND AT INITIAL POINT] 
checkbox to have three long beeps sound (when the 
beep volume is set to long) or three short beeps sound 
(when the beep volume is set to short) when the initial 
point of a setting is reached while selecting basic settings.
The initial point settings are as follows:

These programs are used to set the length of time that 
must elapse until a setting is entered after a key is 
touched, and to disable key repeat.
The setting entry time can be set from 0.0 seconds to 
2.0 seconds in increments of 0.5 seconds.
When [DISABLE AUTO KEY REPEAT] is enabled, only 
one touch is registered if key is touched continuously.
The factory default settings are as follows:

• Time to entry: 0.0 (sec.)
• DISABLE AUTO KEY REPEAT: Disabled

Enable this program if you wish to prevent pausing of 
printing for interrupt copy jobs.
This program is initially disabled (factory default setting).

KEY OPERATOR PROGRAMS

OPERATION SETTINGS

MESSAGE TIME SETTING

KEYS TOUCH SOUND

OK

1/3

6sec

AUTO CLEAR SETTING

60sec

Copy mode

Ratio: 100%
Exposure: 3

Fax mode

Exposure: 3

Network scanner 
mode

Exposure setting: 3

KEY OPERATOR PROGRAMS

KEYS TOUCH SOUND

KEYS TOUCH SOUND AT INITIAL POINT

KEYS TOUCH SOUND

OK

AR-M318_keyope_uk.book  11 ページ  ２００７年１月１１日　木曜日　午後２時４４分

Use this program to enable stream feeding mode.
When this mode is enabled and originals are scanned 
from the RSPF, an original can be added to the RSPF 
within 5 seconds after the previous original is fed, and 
be automatically scanned using the settings of the 
previous original. This function can be used with the 
copy function and the scanner function.
This program is initially disabled (factory default 
setting).

This program is used to change the language used in 
the display.
The factory default setting is "ENGLISH".

When this program is disabled, the display will close 
the screen that is currently open and return to the 
initial screen if no keys are touched for 60 seconds. 
When the program is enabled, the display will not 
close the screen that is currently open.
This program is initially disabled (factory default 
setting).

This program can be enabled to prohibit changes to 
the paper tray settings in the user settings.
Note that bypass tray settings will still be possible.
This program is initially disabled (factory default 
setting).

This program can be enabled to prohibit adjustment of 
the "CLOCK" setting in the custom settings.
This program is initially disabled (factory default 
setting).

 

Use these programs when a peripheral device on the 
machine has failed or when you wish to temporarily 
disable a device. The programs can also be used to 
change the function setting of a device as required by 
your conditions of use.
"DEVICE CONTROL" consists of the following 
programs:

● DISABLING OF DOCUMENT FEEDER

● DISABLING OF DUPLEX

● DISABLING OF STAPLER

● OUTPUT TRAYS

● OFFSET FUNCTION SETTING

● MEMORY FOR PRINTER

● DISABLING OF CENTRE TRAY COUNTING

● RETURN FROM COPY MODE TIMING

● MIX SIZE ORIGINAL FEEDING MODE

● SECURITY SETTINGS

Use this program when the RSPF is not operational or 
you wish to disable the automatic feeding function. 
(Originals can still be scanned using the document 
glass.)
This program is initially disabled (factory default 
setting).

Use this program when you wish to disable the 
two-sided printing function or the function has failed.
When this program is enabled, only one-sided printing 
is possible.This program is initially disabled (factory 
default setting).

Use this program to disable stapling.
When this program is enabled, stapling does not take 
place.This program is initially disabled (factory default 
setting).

KEY OPERATOR PROGRAMS

DEVICE CONTROL

DISABLING OF DUPLEX

DISABLING OF STAPLER

DISABLING OF DOCUMENT
FEEDER

OK

1/3

AR-M318_keyope_uk.book  12 ページ  ２００７年１月１１日　木曜日　午後２時４４分

This program is used to select the respective output 
trays for the copy, printer, and fax functions.
The factory default setting is "PATTERN 1".
Example: When a FINISHER is installed
* Settings that can be selected vary depending on the 

options that are installed.

This program is used to enable or disable the offset 
functions of the centre tray and offset tray (when a 
FINISHER is installed).
This program is initially enabled (factory default 
setting).

This program is used to set the amount of IMC 
memory that is allocated to the printer function. The 
amount of memory can be set from 30% to 70% in 
increments of 10%.
The factory default settings are as follows:

• 50  (%)
• THE MEMORY AREA FOR PRINT HOLD: 30 (%)

● Memory allocated to print hold

(When the PRINTER EXPANSION KIT is installed)
To set the amount of memory allocated to print hold, 
touch the [THE MEMORY AREA FOR PRINT 
HOLD] key. The amount of memory can be set from 
30% to 70% in increments of 10%. If 0% is selected, 
the print hold function cannot be used.

This program is used to disable counting of pages 
delivered to the centre tray.
When this program is enabled, centre tray full 
detection does not take place.
This program is initially disabled (factory default 
setting).

This program is used to set the amount of time that 
must elapse after a copy job is finished before the 
printer or fax function resumes operation. The amount 
of time can be set from 1 second to 60 seconds in 
increments of 1 second.
The factory default setting is "60" (sec.).

When this program is enabled, originals of mixed 
length (the widths must be the same) can be scanned 
in copy mode and each original copied onto the 
corresponding length of paper.
This program is initially disabled (factory default 
setting).

The following settings are related to security. Touch 
the [SECURITY SETTINGS] key to configure the 
settings.

● SSL SETTINGS

SSL can be used for data transmission over a 
network.
SSL is a protocol that enables the encryption of 
information communicated over a network. 
Encrypting data makes it possible to transmit and 
receive sensitive information safely.

• HTTPS: Apply SSL encryption to HTTP 

communication.

• IPP-SSL: Apply SSL encryption to IPP communication.

PATTERN 1

Copy: Offset tray
Printer: Centre tray
Fax: Top tray

PATTERN 2

Copy: Centre tray
Printer: Offset tray
Fax: Top tray

PATTERN 3
(When the fax 
function is enabled)

Copy: Centre tray
Printer: Offset tray
Fax: Centre tray

PATTERN 4
(When the fax 
function is enabled)

Copy: Offset tray
Printer: Centre tray
Fax: Centre tray

03_keyope.fm  13 ページ  ２００７年１月３１日　水曜日　午後３時１８分

This program is used to change the key operator code 
that must be entered to configure the key operator 
programs. When the machine is first used, the key 
operator (adminstrator of the machine) should change 
the key operator code that was set at the factory to the 
desired 5-digit code. (A number that has been 
programmed as an account number cannot be used.) 
Only one key operator code can be programmed.
The factory default setting for the key operator code is 

.

Use these programs to enter the product keys for the 
following options.

This program is used to enter the product key that 
enables the machine to be used as a PostScript 
printer. Ask your dealer for the product key.

This program is used to enter the product key for the 
network scanner function. Ask your dealer for the 
product key.

This program is used to enter the product key for 
E-MAIL ALERT AND STATUS, which enables 
customer product support via a network system. Ask 
your dealer for the product key.

Use this program to display the serial number of the 
machine. The serial number is required when 
obtaining product keys for PS3 EXPANSION KIT, 
NETWORK SCANNER EXPANSION KIT and the 
E-MAIL ALERT AND STATUS.

KEY OPERATOR PROGRAMS

PRODUCT KEY

PS3 EXPANSION KIT

E-MAIL ALERT AND STATUS

NETWORK SCANNER EXPANSION KIT

SERIAL NUMBER

OK

AR-M318_keyope_uk.book  14 ページ  ２００７年１月１１日　木曜日　午後２時４４分