DOWNLOAD Sharp AR-M276 (serv.man6) Service Manual ↓ Size: 8.64 MB | Pages: 127 in PDF or view online for FREE

AR-M236/M276/M237/M277  SIMULATION 8 - 42

1.

Set the guide to the maximum position, and press the [START]
key.
Set WLetter and fit the guide, and press the [START] key.

2.

Set A4R/Letter R and fit the guide, and press the [START] key. 

3.

Set A5R/Invoice R and fit the guide, and press the [START] key. 

4.

Set the guide to the minimum position, and press the [START] key. 

5.

Set the paper recognition width (+), and press the [START] key.

6.

Set the paper recognition width (-),and press the [START] key.

If "FAILED" is displayed in the above procedure 1, 2, 3, or 4, repeat the
adjustment. 

If the middle position adjustment is not required, press the [START]
key without changing the guide position.

1.

Touch the item to be adjusted.
The item and the currently set value are highlighted. 

2.

Enter the RSPF original tray size adjustment value (specified on
the back of the RSPF) with the 10-key. 

With the RSPF or the OC cover open, put a black background chart on
the OC glass (the RSPF glass surface is included for the RSPF stan-
dard model), and press the [START] key. 

If the adjustment is executed normally, the adjustment value is dis-
played and saved in the EEPROM. If an error occurs, "ERR" is dis-
played and the value is not saved in the EEPROM.

If the adjustment is not performed because of abnormality, "---" is dis-
played. 

During execution of the adjustment, the operation cannot be inter-
rupted.

Press the [START] key, and the LSU test is performed.

Used to set the LSU to ON state and check that the sync signal
(HSYNC/) is outputted or not.

After operation for 30 sec, the result is displayed. (Interruption cannot
be made for 5 sec after starting the operation.)

53-6

Adjustment

Used to adjust the detection level of the SPF (RSPF) 
width. The adjustment method is the 4-point system. 
Set the guide to Max. (A3/WLetter) position, A4R/
Letter R position, A5R/Invoice R position, and Min. 
position for adjustment.

SPF (RSPF)

Middle position 
adjustment L

YES

MID-L ADJ.ON

NO

MID-L ADJ.OFF

Middle position 
adjustment S

YES

MID-S ADJ.ON

NO

MID-S ADJ.OFF

AB series

Inch series

53-7

Adjustment

Used to enter the SPF (RSPF) width detection 
adjustment value.

RSPF

Item

Content

Setting range

Default

1

MAX POSITION

Max. width

0 - 999

0

2

POSITION 1

Adjustment point 1

3

POSITION 2

Adjustment point 2

4

MIN POSITION

Min. width 

53-8

Adjustment

Used to adjust the RSPF scan position of the mirror 
unit automatically. For the RSPF scan position 
automatic adjustment, the mirror unit is shifted to 
11mm before the RSPF glass cover edge, and is 
operated automatically to scan images by the unit of 1 
step, detecting the position up to the glass cover 
automatically.
(Adjustment value)
Default: 50, Adjustment range: 1 - 99
Adjustment unit: 1 = about 0.12mm

61-1

Operation test/check

Used to check the LSU (polygon motor) operation.

LSU

Operation

63-1

Adjustment/setting/operation data output/check 
(display/print)

Used to check the result of shading correction. (The 
shading correction data are displayed.)

Scanner (Exposure)

Operation

AR-M236/M276/M237/M277  SIMULATION 8 - 43

Pressing the [START] key performs shading, and displays the result
(center pixel).

Set the RSPF unit OPEN, and press the [START] key.

[ ] indicates the order number of the pixel of the white sheet for SPF
exposure correction in the SPF position.

If the adjustment is normally completed, "COMPLETE" is displayed
and data are written into the EEPROM.
In case of an abnormality, "ERROR" is displayed and no data is written
into the EEPROM.

The SPF white correction start pixel = Displayed pixel position - 34

If the simulation is executed with the RSPF unit closed, an error is
resulted.

1.

Select the print item with the 10-key. 

2.

Press the [START] key.
The display is shifted to the copy menu. 

3.

Select the paper feed tray and the print density. 

4.

Press the [START] key.
Copying is started.

During execution of copying, the [CUSTOM SETTINGS] key and the
[INTERRUPTION] key are invalid.  

* If the IMC board is not installed, the key inputs cannot be made.

Press the keys displayed on the LCD sequentially. 

Adjust the touch panel coordinates. 

When the point of "+" on the LCD is pressed, it turns gray. Press all the
four points of "+."

Check the touch panel coordinates.

Press the keys displayed on the LCD sequentially.

When the touch panel is pressed, the X-coordinate and the Y-coordi-
nate (dot conversion values) are displayed.

63-7

Adjustment

Used to adjust the SPF (RSPF) white correction start 
pixel position automatically.
This adjustment is performed after the lens unit is 
replaced.

Scanner

Operation

64-1

Operation test/check

Used to check the operation of the printer function 
(auto print operation).

Printer

Operation

Item

Content

Setting 

range

Default

1

2 BY 4 
MODE

Self print is made in 2 by 4 mode 
(printing 2 lines and not printing 
4 lines). Since scanning is not 
performed, when the original is 
set on the RSPF, this cannot be 
performed. 
* Duplex print cannot be made.

1-2

1

2

LATTICE 
PRINT

Lattice print (1cm, 1dot width 
WLT, A3 print (A3 main scan, 
WLT sub scan)) is performed.
* Duplex print cannot be made. 

65-1

Adjustment

Used to adjust the touch panel (LCD display section) 
detection position.

Operation (Display, Operation)

65-2

Adjustment/Setting/Operation data output check 
(Display, Print)

Used to check the touch panel (LCD display section) 
detection position adjustment result. 

Operation (Display, Operation)

AR-M236/M276/M237/M277  SIMULATION 8 - 44

Check the key input of the operation panel.
Press the keys displayed on the LCD sequentially.

After completion of all key entries, "COMPLETE" is displayed.

1.

Enter the soft SW number to be selected with the 10-key. 

2.

Check and change the setting content of the selected soft SW. 

3.

Press the [START] key to save the set content. 

The FAX-related soft SW is displayed on the LCD, and changing can
be made by monitoring it.

Note: Executable only when the FAX is installed.

1.

Enter the country code with the 10-key, and press the [START]
key. 

2.

When "1: (YES)" is selected, the soft SW corresponding to the
country code is cleared. When "2: (NO)" is selected, the simulation
is canceled.

Note: Executable only when the FAX is installed.

Press the [START] key.

Read/write can be checked for FAX PWB memory.

The check result is displayed separately for each memory.

1.

Memory to be checked

2.

Detailed procedure

Interruption cannot be made during operation.

Note: Executable only when the FAX is installed.

Select the signal number with the 10-key, and press the [START] key.
The signal is sent to the line and the machine speaker. (Sending the
signal is continued until the [CUSTOM SETTINGS] key is pressed.)

By entering the signal number and pressing the [START] key during
execution, the signal kind can be changed.

65-5

Adjustment/Setting/Operation data output check 
(Display, Print)

Used to check the key inputs of the operation panel.

Operation (screen/operation)

66-1

Setting

Used to change and check the FAX-related soft SW.

FAX

66-2

Adjustment

Used to clear the FAX-related soft SW. (Except for the 
FAX adjustment values)

FAX

1

0 0 0 0 1 0 0 1

1 2 3 4 5 6 7 8

66-3

Operation test/check

FAX PWB memory check

FAX

Operation

DRAM

SRAM

Flash ROM

Program area

SUM check only

Memory area

Option memory

The memory size follows the 
automatically detected value.

PAGE

1

"55H" is written to all the addresses of each memory, and the 
address data are read in sequence to check that they were 
properly written.

2

"AAH" is written to all the addresses of each memory, and the 
address data are read in sequence to check that they were 
properly written.

3

"00H" is written to all the addresses of each memory, and the 
address data are read in sequence to check that they were 
properly written.

4

Perform checks 1 - 3 sequentially. If there is no abnormality, it is 
"OK." If there is any abnormality, "NG" is notified to the error 
address.

5

After completion of check, the memory is returned to the initial 
state.
(CPU is not reset)

66-4

Operation test/check

Signal send modeSignal send mode (Signal send 
level: Max.)

FAX

Operation

1

AR-M236/M276/M237/M277  SIMULATION 8 - 45

Note: Executable only when the FAX is installed.

Select the signal number with the 10-key, and press the [START] key. 

By setting the signal number, signals are sent to the line and the
machine speaker. (Sending signals is continued until interruption com-
mand is made (by pressing [CUSTOM SETTINGS] key.)

By entering the signal number and pressing the [START] key during
execution, the signal kind can be changed.

Note: Executable only when the FAX is installed.

Item

Send signal

Send level

Selection 

menu

1

NO SIGNAL Signal not send

None

2

33.6 V34

–

–

3

31.2 V34

4

28.8 V34

5

26.4 V34

6

24.0 V34

7

16.0 V34

8

19.2 V34

9

16.8 V34

10 14.4 V34

11 12.0 V34

12 9.6 V34
13 7.2 V34

14 4.8 V34

15 2.4 V34
16 14.4 V33

17 12.0 V33

18 14.4 V17
19 12.0 V17

20 9.6 V17

21 7.2 V17
22 9.6 V29

23 7.2 V29

24 4.8 V27t
25 2.4 V27t

26 0.3 FLG

7EH Flag signal

Yes

27 CED2100

Tone signal

Yes

28 CNG1100

29 0.3 V21

30 ANSam
31 RINGER

Pseudo-ringer sound
([ON HOOK] key ON)

None

32 No MSG

Voice message (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
sound composition IC volume to 0.

33 No RBT

Ring back tone (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
G/A volume to 0.

34 DP MAKE

Dial pulse (make)

1: 0dB
2: Soft SW

Maintain the make state with keeping 
the condition to be able to send to the 
dial pulse line.

35 DP BRK

Dial pulse (break)

1: 0dB
2: Soft SW

Maintain the break state with keeping 
the condition to be able to send to the 
dial pulse line.

1

66-5

Operation test/check

Signal send mode (Signal send level soft SW setting)

FAX

Operation

Signal number

Send signal

Send level

Selection 

menu

1 NO SIGNAL Signal not send

None

2 33.6 V34

33.6 V34

–

3 31.2 V34

31.2 V34

–

4 28.8 V34

28.8 V34

–

5 26.4 V34

26.4 V34

–

6 24.0 V34

24.0 V34

–

7 16.0 V34

16.0 V34

–

8 19.2 V34

19.2 V34

–

9 16.8 V34

16.8 V34

–

10 14.4 V34

14.4 V34

–

11 12.0 V34

12.0 V34

–

12 9.6 V34

9.6 V34

–

13 7.2 V34

7.2 V34

–

14 4.8 V34

4.8 V34

–

15 2.4 V34

2.4 V34

–

16 14.4 V33

14.4 V33

–

17 12.0 V33

12.0 V33

–

18 14.4 V17

14.4 V17

–

19 12.0 V17

12.0 V17

–

20 9.6 V17

9.6 V17

–

21 7.2 V17

7.2 V17

–

22 9.6 V29

9.6 V29

–

23 7.2 V29

7.2 V29

–

24 4.8 V27t

4.8 V27t

–

25 2.4 V27t

2.4 V27t

–

26 0.3 FLG

7EH Flag signal

Yes

27 CED2100

Tone signal

Yes

28 CNG1100

29 0.3 V21

30 ANSam
31 RINGER

Pseudo-ringer sound
([ON HOOK] key ON)

None

32 No MSG

Voice message (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
sound composition IC volume to 0.

33 No RBT

Ring back tone (no sound)

None

Under the state where the ring back 
tone can be sent to the line, keep the 
G/A volume to 0.

34 DP MAKE

Dial pulse (make)

1: 0dB
2: Soft SW

Maintain the make state with keeping 
the condition to be able to send to the 
dial pulse line.

35 DP BRK

Dial pulse (break)

1: 0dB
2: Soft SW

Maintain the break state with keeping 
the condition to be able to send to the 
dial pulse line.