Sharp AR-M236 (serv.man11) User Manual / Operation Manual ▷ View online
11
GENERAL PROGRAMS
OPERATION SETTINGS
The "OPERATION SETTINGS" are related to basic
operation of the machine and consist of the following
programs:
operation of the machine and consist of the following
programs:
●
AUTO CLEAR SETTING
●
MESSAGE TIME SETTING
●
KEYS TOUCH SOUND
●
TOUCH KEY OPERATION SETTING
●
DISABLE INTERRUPT PRINT JOB
●
STREAM FEEDING MODE
●
DISPLAY LANGUAGE SETTING
●
DISABLE DISPLAY TIMEOUT
●
DISABLING OF TRAY SETTINGS
AUTO CLEAR SETTING
If no action is taken for a certain length of time when
viewing information on finished jobs, jobs in progress,
or stored jobs, the auto clear function activates and
returns the display to the initial screen of copy mode or
the job status screen. AUTO CLEAR SETTING is used
to set the amount of time that must elapse for the auto
clear function to activate. The time can be set from 10
seconds to 240 seconds in increments of 10 seconds,
or the auto clear function can be disabled. (This setting
only operates in copy mode and network scanner
mode.)
viewing information on finished jobs, jobs in progress,
or stored jobs, the auto clear function activates and
returns the display to the initial screen of copy mode or
the job status screen. AUTO CLEAR SETTING is used
to set the amount of time that must elapse for the auto
clear function to activate. The time can be set from 10
seconds to 240 seconds in increments of 10 seconds,
or the auto clear function can be disabled. (This setting
only operates in copy mode and network scanner
mode.)
MESSAGE TIME SETTING
This program is used to set the length of time that
messages appear in the display (this applies to
messages that appear for a certain length of time and
then automatically disappear.)
The time can be set to as long as 12 seconds in
increments of one second.
messages appear in the display (this applies to
messages that appear for a certain length of time and
then automatically disappear.)
The time can be set to as long as 12 seconds in
increments of one second.
KEYS TOUCH SOUND
This program is used to select whether or not a beep is
sounded when a key is touched, and if sounded, what
type of beep.
The program is also use to select whether or not a
special key touch beep is sounded at the initial point of
a setting.
sounded when a key is touched, and if sounded, what
type of beep.
The program is also use to select whether or not a
special key touch beep is sounded at the initial point of
a setting.
key .... Touch this key to select a low beep
volume. A single beep indicates a valid
key, and a double beep indicates an invalid
key.
key, and a double beep indicates an invalid
key.
key .... Touch this key to select a high beep
volume. A single beep indicates a valid
key, and a double beep indicates an invalid
key.
key, and a double beep indicates an invalid
key.
key .... Touch this key to disable key touch beeps.
Select the [KEYS TOUCH SOUND AT INITIAL POINT]
checkbox to have three long beeps sound (when the
beep volume is set to high) or three short beeps sound
(when the beep volume is set to low) when the initial
point of a setting is reached while selecting basic
settings.
The initial point settings are as follows:
checkbox to have three long beeps sound (when the
beep volume is set to high) or three short beeps sound
(when the beep volume is set to low) when the initial
point of a setting is reached while selecting basic
settings.
The initial point settings are as follows:
TOUCH KEY OPERATION SETTING
These programs are used to set the length of time that
must elapse until a setting is entered after a key is
touched, and to disable key repeat.
The setting entry time can be set from 0.0 seconds to
2.0 seconds in increments of 0.5 seconds.
When [DISABLE AUTO KEY REPEAT] is enabled,
only one touch is registered if key is touched
continuously.
must elapse until a setting is entered after a key is
touched, and to disable key repeat.
The setting entry time can be set from 0.0 seconds to
2.0 seconds in increments of 0.5 seconds.
When [DISABLE AUTO KEY REPEAT] is enabled,
only one touch is registered if key is touched
continuously.
DISABLE INTERRUPT PRINT JOB
(When the printer function is enabled)
When printing in printer mode, printing can be paused
to enble an interrupt copy job to be performed.
Enable this program if you wish to prevent pausing of
printing for interrupt copy jobs.
to enble an interrupt copy job to be performed.
Enable this program if you wish to prevent pausing of
printing for interrupt copy jobs.
KEY OPERATOR PROGRAMS
OPERATION SETTINGS
MESSAGE TIME SETTING
KEYS TOUCH SOUND
OK
1/3
6sec
AUTO CLEAR SETTING
60sec
Mode
Initial point (set from initial screen)
Copy mode
Ratio: 100%
Exposure: 3
Exposure: 3
Fax mode
Exposure: 3
Network scanner
mode
mode
Exposure setting: 3
KEY OPERATOR PROGRAMS
KEYS TOUCH SOUND
KEYS TOUCH SOUND AT INITIAL POINT
KEYS TOUCH SOUND
OK
12
GENERAL PROGRAMS
STREAM FEEDING MODE
Use this program to enable stream feeding mode.
When this mode is enabled and originals are scanned
from the REVERSING SINGLE PASS FEEDER, an
original can be added to the REVERSING SINGLE
PASS FEEDER within 5 seconds after the previous
original is fed, and be automatically scanned using the
settings of the previous original. This function can be
used with the copy function and the scanner function.
When this mode is enabled and originals are scanned
from the REVERSING SINGLE PASS FEEDER, an
original can be added to the REVERSING SINGLE
PASS FEEDER within 5 seconds after the previous
original is fed, and be automatically scanned using the
settings of the previous original. This function can be
used with the copy function and the scanner function.
DISPLAY LANGUAGE SETTING
This program is used to change the language used in
the display.
the display.
DISABLE DISPLAY TIMEOUT
When this program is disabled, the display will close
the screen that is currently open and return to the
initial screen if no keys are touched for 60 seconds.
When the program is enabled, the display will not
close the screen that is currently open.
the screen that is currently open and return to the
initial screen if no keys are touched for 60 seconds.
When the program is enabled, the display will not
close the screen that is currently open.
DISABLING OF TRAY SETTINGS
This program can be enabled to prohibit changes to
the tray settings. Note that bypass tray settings will still
be possible.
the tray settings. Note that bypass tray settings will still
be possible.
DEVICE CONTROL
Use these programs when a peripheral device on the
machine has failed or when you wish to temporarily
disable a device. The programs can also be used to
change the function setting of a device as required by
your conditions of use.
"DEVICE CONTROL" consists of the following
programs:
machine has failed or when you wish to temporarily
disable a device. The programs can also be used to
change the function setting of a device as required by
your conditions of use.
"DEVICE CONTROL" consists of the following
programs:
●
DISABLING OF DOCUMENT FEEDER
●
DISABLING OF DUPLEX
●
DISABLING OF STAPLER
●
OUTPUT TRAYS
●
OFFSET FUNCTION SETTING
●
MEMORY FOR PRINTER
●
DISABLING OF CENTER TRAY COUNTING
●
RETURN FROM COPY MODE TIMING
●
MIX SIZE ORIGINAL FEEDING MODE
DISABLING OF DOCUMENT FEEDER
Use this program when the REVERSING SINGLE
PASS FEEDER has failed or you wish to disable the
automatic feeding function. (Originals can still be
scanned using the document glass.)
PASS FEEDER has failed or you wish to disable the
automatic feeding function. (Originals can still be
scanned using the document glass.)
DISABLING OF DUPLEX
Use this program when you wish to disable the
two-sided printing function or the function has failed.
When this program is enabled, only one-sided printing
is possible.
two-sided printing function or the function has failed.
When this program is enabled, only one-sided printing
is possible.
DISABLING OF STAPLER
(When a FINISHER is installed)
Use this program to disable stapling.
When this program is enabled, stapling does not take
place.
When this program is enabled, stapling does not take
place.
KEY OPERATOR PROGRAMS
DEVICE CONTROL
DISABLING OF DUPLEX
DISABLING OF STAPLER
DISABLING OF DOCUMENT
FEEDER
FEEDER
OK
1/3
13
GENERAL PROGRAMS
OUTPUT TRAYS
(When an output option is installed)
This program is used to select the respective output
trays for the copy, printer, and fax functions.
One of four patterns, [PATTERN 1] through
[PATTERN 4], can be selected.
Example: When a FINISHER is installed
trays for the copy, printer, and fax functions.
One of four patterns, [PATTERN 1] through
[PATTERN 4], can be selected.
Example: When a FINISHER is installed
OFFSET FUNCTION SETTING
This program is used to enable or disable the offset
functions of the center tray and offset tray (when a
FINISHER is installed).
functions of the center tray and offset tray (when a
FINISHER is installed).
MEMORY FOR PRINTER
(When the printer function is enabled)
This program is used to set the amount of IMC
memory that is allocated to the printer function. The
amount of memory can be set from 30% to 70% in
increments of 10%.
memory that is allocated to the printer function. The
amount of memory can be set from 30% to 70% in
increments of 10%.
●
Memory allocated to print hold
(When the PRINTER EXPANSION KIT is installed)
To set the amount of memory allocated to print hold,
touch the [THE MEMORY AREA FOR PRINT
HOLD] key. The amount of memory can be set from
30% to 70% in increments of 10%. If 0% is selected,
the print hold function cannot be used.
(When the PRINTER EXPANSION KIT is installed)
To set the amount of memory allocated to print hold,
touch the [THE MEMORY AREA FOR PRINT
HOLD] key. The amount of memory can be set from
30% to 70% in increments of 10%. If 0% is selected,
the print hold function cannot be used.
DISABLING OF CENTER TRAY
COUNTING
COUNTING
This program is used to disable counting of pages
delivered to the center tray.
When this program is enabled, center tray full
detection does not take place.
delivered to the center tray.
When this program is enabled, center tray full
detection does not take place.
RETURN FROM COPY MODE TIMING
(When the printer function or fax function is enabled)
This program is used to set the amount of time that
must elapse after a copy job is finished before the
printer or fax function resumes operation. The amount
of time can be set from 1 second to 60 seconds in
increments of 1 second.
must elapse after a copy job is finished before the
printer or fax function resumes operation. The amount
of time can be set from 1 second to 60 seconds in
increments of 1 second.
MIX SIZE ORIGINAL FEEDING MODE
When this program is enabled, originals of mixed
length (the widths must be the same) can be scanned
in copy mode and each original copied onto the
corresponding length of paper.
length (the widths must be the same) can be scanned
in copy mode and each original copied onto the
corresponding length of paper.
Settings
Description
PATTERN 1
Copy: Offset tray
Printer: Center tray
Fax: Top tray
Printer: Center tray
Fax: Top tray
PATTERN 2
Copy: Center tray
Printer: Offset tray
Fax: Top tray
Printer: Offset tray
Fax: Top tray
PATTERN 3
(When the fax
function is enabled)
(When the fax
function is enabled)
Copy: Center tray
Printer: Offset tray
Fax: Center tray
Printer: Offset tray
Fax: Center tray
PATTERN 4
(When the fax
function is enabled)
(When the fax
function is enabled)
Copy: Offset tray
Printer: Center tray
Fax: Center tray
Printer: Center tray
Fax: Center tray
14
GENERAL PROGRAMS
KEY OPERATOR CODE
CHANGE
CHANGE
This program is used to change the key operator code
that must be entered to configure the key operator
programs. When the machine is first used, the key
operator (adminstrator of the machine) should change
the key operator code that was set at the factory to the
desired 5-digit code. Only one key operator code can
be programmed.
The factory default setting for the key operator code is
that must be entered to configure the key operator
programs. When the machine is first used, the key
operator (adminstrator of the machine) should change
the key operator code that was set at the factory to the
desired 5-digit code. Only one key operator code can
be programmed.
The factory default setting for the key operator code is
00000
.
PRODUCT KEY
(When the printer function is enabled)
Use these programs to enter the product keys for the
following options.
following options.
PS3 EXPANSION KIT
(When the printer function is enabled)
This program is used to enter the product key that
enables the machine to be used as a PostScript
printer. Ask your dealer for the product key.
enables the machine to be used as a PostScript
printer. Ask your dealer for the product key.
NETWORK SCANNER EXPANSION KIT
(When a PRINT SERVER CARD and NETWORK
SCANNER EXPANSION KIT are installed)
SCANNER EXPANSION KIT are installed)
This program is used to enter the product key for the
network scanner function. Ask your dealer for the
product key.
network scanner function. Ask your dealer for the
product key.
E-MAIL ALERT AND STATUS
(When a PRINT SERVER CARD is installed)
This program is used to enter the product key for
E-MAIL ALERT AND STATUS, which enables
customer product support via a network system. Ask
your dealer for the product key.
E-MAIL ALERT AND STATUS, which enables
customer product support via a network system. Ask
your dealer for the product key.
SERIAL NUMBER
Use this program to display the serial number of the
machine. The serial number is required when
obtaining product keys for PS3 EXPANSION KIT,
NETWORK SCANNER EXPANSION KIT and the
E-MAIL ALERT AND STATUS.
machine. The serial number is required when
obtaining product keys for PS3 EXPANSION KIT,
NETWORK SCANNER EXPANSION KIT and the
E-MAIL ALERT AND STATUS.
KEY OPERATOR PROGRAMS
PRODUCT KEY
PS3 EXPANSION KIT
E-MAIL ALERT AND STATUS
NETWORK SCANNER EXPANSION KIT
SERIAL NUMBER
OK
Click on the first or last page to see other AR-M236 (serv.man11) service manuals if exist.