Sharp AR-LC5 (serv.man3) Service Manual ▷ View online
AR-LC5 ADJUSTMENT 7 - 1
[7] ADJUSTMENT
Lift-up motor (LLM) installing position adjustment
Install the motor so that the lift-up motor shaft comes to the center of
the insertion port of the lift-up motor installing plate shaft.
the insertion port of the lift-up motor installing plate shaft.
AR-LC5 MAINTENANCE 8 - 1
[8] MAINTENANCE
Make sure to disconnect the phone line/communication cable from the copier before performing maintenance, because receiving the signal during
maintenance is dangerous.
maintenance is dangerous.
1. Maintenance system table
❍
: cleaning
★
: lubrication
✕
: checking (cleaning, replacement or adjustment as required)
2. Details of maintenance
A. Driving section
Unit name
Name
80K
160K
240K
320K
Remarks
Driving section
Paper feed and transport gear
★
★
★
★
Lift-up gear
★
★
★
★
Transport section
Transport roller
❍
❍
❍
❍
Paper guide
❍
❍
❍
❍
Paper feed section
Paper feed roller
✕
✕
✕
✕
Replacement period (80K or 2 years)
Reversion roller
✕
✕
✕
✕
Replacement period (80K or 2 years)
Hitching roller
✕
✕
✕
✕
Replacement period (80K or 2 years)
Torque limiter
✕
✕
✕
✕
No.
Name
Operation
Cycle
Remarks
1
Paper feed and transport gear
Lubrication
80K
2
Lift-up gear
Lubrication
80K
2
1
AR-LC5 MAINTENANCE 8 - 2
B. Paper feed and transport section
No.
Name
Operation
Cycle
Remarks
1
Transport roller
Cleaning
80K
2
Paper feed guide
Cleaning
80K
3
Paper feed roller
Check
✱
80K
Replacement period (80K or 2 years)
4
Reversion roller
Check
✱
80K
Replacement period (80K or 2 years)
5
Hitching roller
Check
✱
80K
Replacement period (80K or 2 years)
6
Torque limiter
Check
✱
80K
Replacement period (80K or 2 years)
4
6
3
5
2
1
1
AR-LC5 TROUBLESHOOTING 9 - 1
[9] TROUBLESHOOTING
1. Trouble code list
2. Self-diagnostics
∗
Displayed on the control panel of the copier
If a trouble occurs check the cause of the trouble using the following
flow charts.
flow charts.
N: No
Y: Yes
A. LCC does not operate
Trouble
code
Trouble
Remarks
Trouble
detection
U6
09
LCC lift motor trouble
–
LCC
20
LCC communication trouble
–
PCU
21
LCC transport motor trouble
–
LCC
22
LCC 24V power trouble
–
LCC
Trouble
code
Details of trouble
U6
09
Content
LCC lift motor trouble
Detail
LCC lift motor trouble
Cause
Sensor defective
LCC control PWB defective
Gear broken
Lift motor defective
LCC control PWB defective
Gear broken
Lift motor defective
Check and
remedy
remedy
Check sensor operation with SIM4-2.
Check lift motor operation with SIM4-3.
Check lift motor operation with SIM4-3.
20
Content
LCC communication trouble
Detail
Communication trouble with LCC
Error at communication line test when
power is turned on or leaving SIM.
Error at communication line test when
power is turned on or leaving SIM.
Cause
Connector: Defective connection of harness
or broken wire
LCC control PWB defective
Control PWB (PCU) defective
Control PWB (PCU) defective
Malfunction due to noise
or broken wire
LCC control PWB defective
Control PWB (PCU) defective
Control PWB (PCU) defective
Malfunction due to noise
Check and
remedy
remedy
Can be reset by turning on and off power
supply.
Check communication line connector and
harness.
supply.
Check communication line connector and
harness.
21
Content
LCC transport motor trouble
Detail
LCC transport motor operation trouble
Cause Motor
lock
Motor speed error
Overcurrent to motor
LCC control PWB defective
Overcurrent to motor
LCC control PWB defective
Check and
remedy
remedy
Check transport motor operation with SIM4-
3.
3.
22
Content
LCC24V power supply error
Detail
No power supply (24V) to LCC
Cause
Connector: Harness connection defective or
broken wire
LCC control PWB defective
Power supply unit defective
broken wire
LCC control PWB defective
Power supply unit defective
Check and
remedy
remedy
Check power supply line connector and
harness.
Check for 24V at power supply unit and
LCC control PWB
harness.
Check for 24V at power supply unit and
LCC control PWB
N
Y
N
Y
N
Y
N
A
F
Y
D
B
Is interface
harness properly
connected?
+5V between
CN-B-7 and 8 of
control PWB?
+24V between
CN-B9 and 10 of
control PWB?
Ready state after
setting paper?
Connect properly.
Check and if necessary
replace harness.
Check and if necessary
replace harness.
Click on the first or last page to see other AR-LC5 (serv.man3) service manuals if exist.