Sharp AR-FX9 Service Manual ▷ View online
AR-FX9 TEST COMMAND 3 - 8
66
13
Dial test
[Function]
Use to the dial test.
Use to the dial test.
[Operation]
17
DTMF signal send (Max.
value)
value)
[Function]
Use to set the DTMF signal send (Max. value).
Use to set the DTMF signal send (Max. value).
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
■
Dial test (PULSE)
1) Initial display
∗
[CLEAR] key: Returns to the main-
sub code input display.
sub code input display.
2) Select 1
3) Enter the make time in 2 digits.
XXXX: Default
∗
After deleting with [CLEAR] key,
input can be made.
input can be made.
4) [ENTER] key
"yy" is the selected pulse 10 or 20.
"xx" is the input value.
∗
Select 2: Returns to “2)” display.
5) Select 1
Switched to 10/20PPS set with
pulse selection inside.
pulse selection inside.
6) After setting
7) After completion of sending
∗
Select 2: Returns to “4)” display.
8) Select 1
After 2sec, returns to "1) Initial display".
SELECT SIGNAL
1:PULSE 2:DTMF
INPUT MAKE TIME
(0-15) __
INPUT DIAL #
XXXX
SEND yyPPS xxms
1:YES 2:NO
SENDING yyPPS xxms
TERMINATE ?
1:YES 2:NO
TERMINATED
■
Dial test (DTMF)
1) Initial display
∗
[CLEAR] key: Returns to the main-sub code input dis-
play.
play.
2)
Select 2
↓
Select 2
3)
Select 1
↓
↓
Select 2
4) Select 1
↓
XXXX: Default
∗
After deleting with [CLEAR] key, input can be made.
4) [ENTER] key
"xx" indicates HI, and "yy" indicates Low Soft SW.
∗
Select 2: Returns to “4)” display.
5) Select 1
HI/LO is selected with the signal level inside.
6) After setting the signal send level
7) After completion of sending
∗
Select 2: Returns to “4)” display.
8) Select 1
After 2sec, returns to "1) Initial display".
SELECT SIGNAL
1:PULSE 2:DTMF
SELECT HIGH LEVEL
1:DEFAULT 2:SOFT SW.
↓
INPUT VALUE
(0-15) __
SELECT LOW LEVEL
1:DEFAULT 2:SOFT SW.
↓
INPUT VALUE
(0-15) __
INPUT DIAL #
XXXX
H:xx L:yy
1:YES 2:NO
SENDING DTMF
TERMINATE ?
1:YES 2:NO
TERMINATED
1) Initial display
∗
[CLEAR] key: Returns to the main-sub code
input display.
input display.
2) [10KEY] input
The content selected with signal send level
selection is set inside.
selection is set inside.
3) Communication is started after setting the
signal send level.
∗
[CLEAR] key: Returns to "1) Initial display".
INPUT DIAL #
SENDING SIGNAL MAX
PRESS CLEAR TO STOP
AR-FX9 TEST COMMAND 3 - 9
66
18
DTMF signal send (Soft SW
set value)
set value)
[Function]
Use to set the DTMF signal send (Soft SW set value).
Use to set the DTMF signal send (Soft SW set value).
[Operation]
21
FAX information print
[Function]
Use to print the FAX information.
Use to print the FAX information.
[Operation]
24
FAST SRAM clear
[Function]
Use to clear the FAST SRAM.
Use to clear the FAST SRAM.
[Operation]
30
TEL/LIU status change
check
check
[Function]
Use to check the TEL/LIU status change.
Use to check the TEL/LIU status change.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
1) Initial display
∗
[CLEAR] key: Returns to the main-sub code
input display.
input display.
2) [10KEY] input
The content selected with signal send level
selection is set inside.
selection is set inside.
3) Communication is started after setting the
signal send level.
∗
[CLEAR] key: Returns to "1) Initial display".
INPUT DIAL #
SENDING SIGNAL SSW
PRESS CLEAR TO STOP
1) Initial display
2) [
←
/
→
] or after 2sec
Every time when [
→
] key is pressed, the second line is changed in the sequence of 1
→
2
→
3
→
1.
When [
←
] key is pressed, the sequence is reversed.
∗
[CLEAR] key: Returns to the main-sub code input display.
3) [ENTER] key
• When print is allowed
After completion of printing,
main code and sub code input
display.
main code and sub code input
display.
• When print is inhibited
After 2sec, FAX control is
terminated.
terminated.
SELECT REPORT (1-3)
PRESS
←
,
→
SELECT REPORT (1-3)
1:USER SW. LIST
SELECT REPORT (1-3)
2:SOFT SW. LIST
SELECT REPORT (1-3)
3:PROTOCOL
PRINT STORED
CAN NOT PRINT
1) Initial display
2) After completion of clearing
After 2sec, main code and sub code input dis-
play.
play.
CLEAR FAST SRAM
CLEARED
1) Initial display
↑
The display is switched every 2sec.
↓
∗
[CLEAR] key: Returns to the main-sub code input display.
HS2 :xxx HS1 :xxx
RHS :xxx EXHS:xxx
CHECKING
PRESS CLEAR TO STOP
AR-FX9 TEST COMMAND 3 - 10
66
32
Receive data check
[Function]
Use to check the receive data.
Use to check the receive data.
[Operation]
33
Signal detection check
[Function]
Use to check the signal detection.
Use to check the signal detection.
[Operation]
34
Communication time
measurement
measurement
[Function]
Use to measurement the communication time.
Use to measurement the communication time.
[Operation]
37
Speaker sound volume
setting
setting
[Function]
Use to set the speaker sound volume.
Use to set the speaker sound volume.
1: NO SOUND
2: LOW
3: MID
4: HIGH
2: LOW
3: MID
4: HIGH
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
1) Initial display
2) After completion of reception
"xx" is "OK" or "NG" depending on the check
result.
result.
∗
[CLEAR] key: Returns to the main-sub code
input display.
input display.
RECEIVING
RESULT
xx
1) Initial display
When a signal is detected, the display is changed from NONE to the following.
CI/CNG/CED/BT/DT/Flag/SDT/DTMF
∗
[CLEAR] key: Returns to the main-sub code input display.
CHECKING NONE
PRESS CLEAR TO STOP
1) Initial display
"xx:xx:xx:xxx" indicates o'clock, minute, second, millisecond.
∗
[CLEAR] key: Returns to the main-sub code input display.
COMM. TIME
xx:xx:xx:xxx msec
1) Initial display
2) [
←
/
→
] or after 2sec
Every time when [
→
] key is pressed, the second line is changed in the sequence of 1
→
2
→
3
→
4
→
1.
When [
←
] key is pressed, the sequence is reversed.
∗
[CLEAR] key: Returns to the main-sub code input display.
3) [ENTER] key
xxx: Set content
After 2sec, main code and sub code input display.
SELECT SPEEKER VOL.
PRESS
←
,
→
SELECT (1-4)
1:NO SOUND
SELECT (1-4)
2:LOW
.....
STORED
xxx
AR-FX9 TEST COMMAND 3 - 11
66
38
Time setting/check
[Function]
Use to check the time setting.
Use to check the time setting.
[Operation]
41
CI signal check
[Function]
Use to check the CI signal.
Use to check the CI signal.
When CI signal is detected, OFF
→
ON.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
1) Initial display
∗
[CLEAR] key: Returns to the main-sub code
input display.
input display.
2) Select 1
"xxxx.xx.xx(xxx)" is the current value. (No revi-
sion of display)
sion of display)
3)
Select 1
∗
Select 2: Returns to "1) Initial display".
4) Enter the year in 4 digits.
5) Enter the month in 2 digits.
6) Enter the day in 2 digits.
"xxxx.xx.xx(xxx) is the entered value.
∗
Select 2: Returns to "1) Initial display".
7) Select 1
After 2sec, returns to "1) Initial display".
2) Select 2
"xx:xx" is the current value.
3) Select 1
∗
Select 2: Returns to "1) Initial display".
4) Enter o'clock in 2 digits.
5) Enter minute in 2 digits.
"xx:xx" is the current value.
∗
Select 2: Returns to "1) Initial display".
6) Select 1
After 2sec, returns to "1) Initial display".
SELECT TO SET
1:DATE 2:TIME
xxxx.xx.xx(xxx)
CHANGE? 1:YES 2:NO
INPUT YEAR
(4 DIGITS)____.__.__
INPUT MONTH
(1-12) 1998.__.__
INPUT DAY
(1-31) 1998.01.__
xxxx.xx.xx(xxx)
STORED? 1:YES 2:NO
STORED
xx:xx
CHANGE? 1:YES 2:NO
INPUT HOUR
(0-24) __:__
INPUT MINUTE
(00-59) 01:__
xx:xx
STORED? 1:YES 2:NO
STORED
1) Initial display
∗
[CLEAR] key: Returns to the main-sub code input display.
CHECKING CI:OFF
PRESS CLEAR TO STOP
Click on the first or last page to see other AR-FX9 service manuals if exist.