Sharp AR-FX11 Service Manual ▷ View online
AR-FX11 SIMULATIONS, FAX SOFTWARE SWITCH 6-18
66
33
Signal detection check
Used to detect signals and display the result with ON/OFF.
34
Communication time measurement
Used to perform a send/receive test and measure and display the time required for send/receive of the
image data in the communication.
image data in the communication.
Main
code
code
Sub
code
Contents
Remark
CI : FNET:
EXEC
Sim66-33 SIGNAL CHK
CNG : CED :
BT : DT :
BT : DT :
EXEC
Sim66-33 SIGNAL CHK
1:CI FNET
2:CNG CED BT DT
3:Flag SDT DTMF
(1 - 3)
2:CNG CED BT DT
3:Flag SDT DTMF
(1 - 3)
X
Sim66-33 SIGNAL CHK
Flag: SDT :
DTMF:
DTMF:
EXEC
OK
Sim66-33 SIGNAL CHK
CI :OFF FNET:OFF
DETECT
EXEC
Sim66-33 SIGNAL CHK
CNG :OFF CED :OFF
BT :OFF
BT :OFF
DT :OFF
DETECT
EXEC
Sim66-33 SIGNAL CHK
Flag:OFF SDT :OFF
DTMF:OFF
DTMF:OFF
DETECT
EXEC
Sim66-33 SIGNAL CHK
After selection with 10-key
OK
After pressing OK key,
during execution
during execution
OK
After pressing OK key,
during execution
during execution
OK
After pressing OK key,
during execution
during execution
SIM66-33 initial window
SIM66-33 initial window
SIM66-33 initial window
1:CI FINET
2:CNG CED BT DT
3:Flag SDT DTMF
Return
Return
Return
CA key
: Simulation cancel
Interrupt key : Sub code input window
C key
C key
: Input clear
10-key
: Item selection
ON key
: Input value settlement and execution
START key
: Similar to OK key
Signal detection
YES/NO is displayed
with ON/OFF.
YES/NO is displayed
with ON/OFF.
Signal detection
YES/NO is displayed
with ON/OFF.
YES/NO is displayed
with ON/OFF.
Signal detection
YES/NO is displayed
with ON/OFF.
YES/NO is displayed
with ON/OFF.
Sim66-34 COMM. TIME
OK
Sim66-34 COMM. TIME
EXEC
COMM. TIME:
xxx:xx:xx:xxxms
Simulation code input window
CA key
: Simulation cancel
Interrupt key : Sub code input window
OK key
OK key
: Settlement
Return key
: Simulation code input window
START key : Settlement
C key
C key
: Disable
Immediately after pressing OK key,
the window shifts to the next one.
the window shifts to the next one.
Return
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 18 ページ ２００４年１１月１２日 金曜日 午後２時２４分
AR-FX11 SIMULATIONS, FAX SOFTWARE SWITCH 6-19
66
37
Speaker sound volume adjustment
Used to send the following test sounds to the line and the speaker to perform the adjustment of the sound
variation and the sound volume.The send level to the line is determined by the soft SW set value. The
selected sound variation and the sound volume are written into the corresponding soft SW.
variation and the sound volume.The send level to the line is determined by the soft SW set value. The
selected sound variation and the sound volume are written into the corresponding soft SW.
Main
code
code
Sub
code
Contents
Remark
Sim66-37 SPEAKER
Sim66-37 SPEAKER
OK
Sim66-37 SPEAKER
1:RINGER
2:LINE MONITOR
3:ON HOOK
( 1 - 6 )
2:LINE MONITOR
3:ON HOOK
( 1 - 6 )
X
ON HOOK SMA.
1:SMA.-1 3:LAR.-3
2:MED.-2 4:DF VOL.
( 1 - 4 )
1:SMA.-1 3:LAR.-3
2:MED.-2 4:DF VOL.
( 1 - 4 )
X
OK
ON HOOK
SMALL -1
PRESS BACK TO STOP
SMALL -1
PRESS BACK TO STOP
EXEC
Sim66-37 SPEAKER
4:SCAN FINISH
5:TX/RX FINISH
6:DTMF
( 1 - 6 )
5:TX/RX FINISH
6:DTMF
( 1 - 6 )
X
Sim66-37 SPEAKER
ON HOOK
1:SMA.2:MED.3:LAR.
1:SMA.2:MED.3:LAR.
( 1 - 3 )
X
Select
"4: DEFAULT VOL."
"4: DEFAULT VOL."
A sound is delivered while EXEX is highlighted.
Ringing until RETURN
key is pressed.
key is pressed.
After completion, the display
shifts to SIM66-37 window.
shifts to SIM66-37 window.
Sim66-37 SPEAKER
ON HOOK
SMALL -1
1 2 3 4 5 6 7
( 1 - 3 )
SMALL -1
1 2 3 4 5 6 7
( 1 - 3 )
X
OK
OK
Sim66-37 SPEAKER
ON HOOK
SMALL -1
PRESS BACK TO STOP
SMALL -1
PRESS BACK TO STOP
EXEC
Ringing while EXEC is displayed.
Ringing until RETURN key is pressed.
Ringing until RETURN key is pressed.
Mute setting available
Sim66-37 SPEAKER
Sim66-37 SPEAKER
OK
Sim66-37 SPEAKER
1:RINGER
2:LINE MONITOR
3:ON HOOK
( 1 - 6 )
2:LINE MONITOR
3:ON HOOK
( 1 - 6 )
X
LINE MONITOR SMA.
1:SMA.-1 3:LAR.-3
2:MED.-2 4:DF VOL.
( 1 - 5 )
1:SMA.-1 3:LAR.-3
2:MED.-2 4:DF VOL.
( 1 - 5 )
X
OK
LINE MONITOR
SMALL -1
PRESS BACK TO STOP
SMALL -1
PRESS BACK TO STOP
EXEC
Sim66-37 SPEAKER
4:SCAN FINISH
5:TX/RX FINISH
6:DTMF
( 1 - 6 )
5:TX/RX FINISH
6:DTMF
( 1 - 6 )
X
Sim66-37 SPEAKER
LINE MONITOR SMA.
5:NON
5:NON
( 1 - 5 )
X
Ringing while EXEC is displayed
Ringing while EXEC is displayed
After completion, the display shifts
to SIM66-37 initial window.
to SIM66-37 initial window.
Sim66-37 SPEAKER
LINE MONITOR
1:SMA.2:MED.3:LAR.
1:SMA.2:MED.3:LAR.
( 1 - 3 )
X
Sim66-37 SPEAKER
LINE MONITOR
SMALL -1
PRESS BACK TO STOP
SMALL -1
PRESS BACK TO STOP
EXEC
3sec later
3sec later
When "4: DEFAULT VOL" is selected
Sim66-37 SPEAKER
LINE MONITOR
SMALL -1
1 2 3 4 5 6 7
( 1 - 3 )
SMALL -1
1 2 3 4 5 6 7
( 1 - 3 )
X
OK
OK
"NO SOUND" cannot be set for DTMF, either.
CA key
: Simulation cancel
Interrupt key : Sub code input window
C key
C key
: Input clear
keys
: Page switch
10-key
: Item selection, sound volume selection
OK key
: Settlement and execution.
After completion, a sound rings for several
seconds and the display shift to the selection
window.
seconds and the display shift to the selection
window.
START key
: Input value settlement
RETURN key : Returns to the selection window.
After setting "DEFAULT VOL,"
ON HOOKSMALL
RETURN key
ON HOOK
1: SMA. 2: MED. 3: LAR
1: SMA. 2: MED. 3: LAR
RETURN key
Returns to
ON HOOK
1: SMA -2
2: MED.-4
3: LAR -7
4: DEFAULT VOL.
ON HOOK
1: SMA -2
2: MED.-4
3: LAR -7
4: DEFAULT VOL.
Return
Return
Return
Return
Return
Return
After selection with 10-key
After selection
with 10-key
with 10-key
After selection with 10-key
After selection
with 10-key
with 10-key
After selection
with 10-key
with 10-key
After selection with 10-key
After selection
with 10-key
with 10-key
After selection
with 10-key
with 10-key
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 19 ページ ２００４年１１月１２日 金曜日 午後２時２４分
AR-FX11 SIMULATIONS, FAX SOFTWARE SWITCH 6-20
66
38
Time setting/check
Used to write/read the time (year, month, day, o'clock, minute) into/from the RTC on the FAX PWB.
41
CI signal check
Used to detect the call signal from CI pin and send the call sound to the line and the speaker. The sound
volume of the call sound follows the soft SW setting. The operations of signal detection and the pseudo ring
sound send when the signal is detected are continued until the interruption command is made by pressing
RETURN key.
volume of the call sound follows the soft SW setting. The operations of signal detection and the pseudo ring
sound send when the signal is detected are continued until the interruption command is made by pressing
RETURN key.
Main
code
code
Sub
code
Contents
Remark
Sim66-38 DATE & TIME
Sim66-38 DATE & TIME
Sim66-38 DATE & TIME
Sim66-38 DATE & TIME
Sim66-38 DATE & TIME
DATE
YEAR
YEAR
XXXX
(2004-2062)
YY
DATE
MONTH
MONTH
XX
(1-12)
YY
After inputting with 10 key, press OK key.
OK
DATE
DAY
DAY
XX
(1
31)
YY
TIME
XX:XX
(00-23)
YY
YEAR
20YY
MONTH
YY
DAY
YY
EXEC
After inputting with 10-key
OK
After inputting with 10-key
OK
After execution, the display shifts
to the sub code input window.
to the sub code input window.
After inputting with 10 key, press OK key.
OK
Sim66-38 DATE & TIME
TIME
XX:XX
(00-59)
YY
OK
After inputting with 10-key
OK
xx: The current year/month/day is displayed.
yy: The input value is displayed.
yy: The input value is displayed.
xx:xx: The current time is displayed.
yy: The input value is displayed.
yy: The input value is displayed.
CA key
: Simulation cancel
Interrupt key : Sub code input window
10-key
10-key
: Item selection and time input
OK key
: Settlement
START key
: Settlement
RETURN key : Returns to the previous window or
the simulation code input window.
C key
: Input value clear
Sim66-41 CI SIGNAL
OK
Sim66-41 CI SIGNAL
CHECK CI SIGNAL
EXEC
After pressing OK key, during execution
CI:OFF
PRESS BACK TO STOP
PRESS BACK TO STOP
EXEC
When RETUREN key is pressed, the
window shifts to SIM66-41 input window.
window shifts to SIM66-41 input window.
When detected, OFF is changed to ON.
When RETURN key is pressed during detection,
the display shifts to SIM66-41 input window.
the display shifts to SIM66-41 input window.
CA key
: Simulation cancel
Interrupt key : Sub code input window
OK key
OK key
: Settlement
RETURN key : Returns to the simulation code
input window.
Return
Return
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 20 ページ ２００４年１１月１２日 金曜日 午後２時２４分
AR-FX11 SIMULATIONS, FAX SOFTWARE SWITCH 6-21
66
52
Pseudo ringer check
• The pseudo ringer sound is delivered both from the machine (speaker).
• This operation is continued until the interruption command is made by pressing RETURN key.
• The LCD displays the TEL/LIU status and the HOOK status.
• The LCD displays the TEL/LIU status and the HOOK status.
• While the pseudo ringer is delivered, the RBT )ring back tone) is delivered to the line. The bell is ON for
1sec and OFF for 2sec.
Main
code
code
Sub
code
Contents
Remark
Sim66-52 PSEUDO RNG
OK
Sim66-52 PSEUDO RNG
PSEUDO RINGER CHK
EXEC
After pressing OK key, during execution
PSEUDO RINGER CHK
PRESS BACK TO STOP
PRESS BACK TO STOP
EXEC
SIM66-52 initial window
CA key
: Simulation cancel
Interrupt key : Sub code input window
OK key
OK key
: Execution
RETURN key : Returns to the selection window.
START key
START key
: ExecutionC key: Disable
Return
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 21 ページ ２００４年１１月１２日 金曜日 午後２時２４分
Click on the first or last page to see other AR-FX11 service manuals if exist.