DOWNLOAD Sharp AR-F13 (serv.man2) Service Manual ↓ Size: 2.98 MB | Pages: 64 in PDF or view online for FREE

AR-F13  UNPACKING AND INSTALLATION  3-4

<6> Reattach the removed cover so that the four securing bosses

of the cover are inserted into the four positioning holes and
then tighten the four screws in the order of <1> and <2>
shown in the illustration to secure the cover.

10) Connect the connector of the saddle finisher.

<1> Remove the screw that secures the power supply cover at

the rear face of the stand and remove the power supply
cover.

<2> Cut out the portion of the power supply cover shown in the

illustration.

<3> Secure the power supply cover to the rear cabinet.

<4> Connect the connector for connecting the saddle finisher to

the connector on the stand and secure it with the screw on
the connector.

If another peripheral device must be installed, carry out the following
steps at the end of the installation work.

11) Move the staple unit of the saddle finisher to

      the cartridge insertion position.

<1> Insert the power plug of the main unit to the outlet and turn

on the main switch.

<2> Wait for some time until the initial operation of the saddle fin-

isher is complete.

12) Set the staple cartridge to the staple unit.

<1> Open the front cover of the saddle finisher and pull out the

staple unit.

<2> Push the staple cartridge securely into the staple section until

it clicks.

13) Attach the staple unit to the finisher.

Insert the staple section and close the front cover of the finisher.

14) Paste the staple position label.

Open the front cover and paste staple position label A to the posi-
tion shown in the illustration.

If the B/W scanner module/DSPF is attached, paste staple position
label B to the position on the B/W scanner module/DSPF shown in
the illustration.

Cover

Screw

Screw

Screw

Screw

Power supply cover

Screw

Cut-out portion

Connector

Screw

Check that the right 
and left of the staple 
cartridge are not 
loose.

Y

X

For Scanner

For RADF

X

Y

AR-F13  UNPACKING AND INSTALLATION  3-5

For installation of AR-PN1A/PN1B/PN1C/PN1D, a saddle stitch

finisher (AR-FN13) must have been installed.

1) Turn off the main switch of the main unit of the printer.

<1> Turn the main switch located on the front side of the main

unit to the "OFF" position.

<2> Then remove the power plug of the main unit from the outlet.

<3> Loosen the screw and remove the connector of the finisher.

2) Remove the front cover from the right front of the finisher.

Remove the screws A and B (two for each) that secure the finisher
front cover and remove the front cover.

3) Remove the front cabinet and the rear cabinet from the finisher.

<1> Open the front door of the finisher and remove the jam han-

dling dial.

<2> Remove the four front cabinet securing screws, pull out the

staple unit until it stops, then remove the pawl of the front
cabinet in the direction indicated by the arrow and remove
the front cabinet.

<3> Remove the three rear cabinet securing screws, remove the

pawl in the direction indicated by the arrow, and remove the
rear cabinet.
At this time, remove the relay harness through the opening of
the rear cabinet.

Screw

(M4 x 6 with rosette)

: 1 pc.

Harness A (purple): 1 pc.

Harness B (orange): 1 pc.

Dust box label:

 1 sheet

Hole punch position label*: 

2 sheets

* Will not be used.

Use the hole punch 
position labels packed 
in AR-F13.

Connector

Screw

Screws B

Screws A

Front cover

Jam handling dial

Staple unit

Pawl

Screws

Screws

Front cabinet

Screw

Relay harness

Opening for
relay harness

Screw

Rear
cabinet

Pawl

AR-F13  UNPACKING AND INSTALLATION  3-6

4) Remove the top cover.

<1> Remove the four top cover securing screws and remove the

top cover.

<2> Remove the four pawls from the top cover and separate the

cover into the upper and lower portions. Reuse the upper
portion.

5) Remove the paper-in PG of the punch unit.

<1> Remove the dust box.

<2> Remove the two paper-in PG securing screws.

<3> Remove the upper bosses of the paper-in PG.

<4> Remove the lower bosses of the paper-in PG with a minus

screwdriver etc.

<5> Remove the paper-in PG.

<6> Reattach the dust box.

Top cover

Screw

Top cover

Pawl

Pawl

AR-F13  UNPACKING AND INSTALLATION  3-7

6) Attach the punch module.

<1> Insert the two bosses of the punch unit into the boss holes of

the finisher and fix the punch module using three screws.

Note: For the screws, use a supplied screw and the two screws

that have been removed in step 4).

7) Connect the harness of the punch module to the PWB of the fin-

isher.

Remove the clamps that fix the harness, handle the wiring of har-
ness A (purple) and harness B (orange), and fix them with the
clamps.

8) Reattach the covers that have been removed.

<1> Hang the two pawls of the top cover and secure them using

the two screws.

<2> Pass the relay harness to the rear cabinet and secure the

rear cabinet using the three screws.

<3> Remove the lock release lever that has been attached to the

front cabinet.
Reattach the front cabinet to its original position, push in the
staple unit, and attach it using the two screws.
Insert the protrusion (B) of the lock release lever that has
been removed before to the hole (C) of the latch arm.
After attaching it, move the lever to check that it moves
smoothly.
If the lever does not move smoothly, remove the lock release
lever by releasing the pawl at the lower part of the lock
release lever using a flat-blade screwdriver or the like and
then insert it again.

Boss

Boss hole

Boss

Boss hole

Screw (with rosette)
(supplied with this unit)

Screw

Screw

Punch module

Clamps

Clamps

Harness A (purple)

Harness B (orange)

Harness A (purple)

Harness B (orange)

Screw

Screw

Top cover

Pawl

Screw

Relay harness

Opening for
relay harness

Screws

Rear cabinet

Staple unit

Screws

Front cabinet

Lock release 
lever (A)

Projection (B)

Latch arm

Pawl (D)