Sharp AR-F13 (serv.man2) Service Manual ▷ View online
AR-F13 EXTERNAL VIEWS AND INTERNAL STRUCTURES 2-3
4. Puncher section (AR-PN1)
A. Sensor
B. Motor
C. PWB
Code
Name
Active condition
Remark
Punch home position
sensor
sensor
Punch HP detected:"L"
In the
punch unit
punch unit
PSHPS Punch side home
position
Punch slide unit HP
detected:"H"
detected:"H"
In the
punch unit
punch unit
PE
Punch dust sensor
In the
punch unit
punch unit
Code
Name
Active condition
Remark
FPNM Punch motor
Punch drive
FPSM
Punch side motor
Punch slide unit
transverse move
transverse move
PSHPS
PE
Punch home position
FPSM
FPNM
Code
Name
[1]
Punch driver PWB
[2]
Side resist photo sensor PWB
[3]
Side resist LED PWB
[4]
Dust full photo sensor PWB
[5]
Dust full LED PWB
[1]
[2]
[3]
[5]
[4]
AR-F13 UNPACKING AND INSTALLATION 3-1
[3] UNPACKING AND
INSTALLATION
1. AR-F13
<Before installation>
• Start installation after checking that the DATA indicator on the oper-
ation panel is neither lit nor blinking.
• For installation of AR-F13, an optional stand (AR-D17, AR-D18 or
AR-D19) and a duplex bypass/inverter unit (AR-RB1) must have
been installed.
been installed.
• Ensure that the connecting plate on the front of the optional stand
and the two supplied connection plates are securely attached.
1) Turn off the main switch.
<1> Turn the main switch located at the left side of the main unit
to the "OFF" position.
<2> Remove the power plug from the outlet.
2) Remove the actuator.
<1> While holding the base of the exit actuator of the duplex
bypass/inverter unit with one hand, pull the end of the exit
actuator with the other hand to remove the actuator.
actuator with the other hand to remove the actuator.
<2> If the exit tray is installed to the duplex bypass/inverter unit,
remove it.
3) Attach the lock plate and the grounding plate.
<1> Remove the screw from the rear side of the duplex bypass/
inverter unit.
<2> Put the lock plate to the duplex bypass/inverter unit and
attach it with screw C on the front side and with screw D on
the rear side.
the rear side.
<3> Remove the exterior securing screw, put the two grounding
plates to the main unit, and secure them with screws C (two
for each).
for each).
∗
At this time, attach the front grounding plate so that marking F is
positioned up.
positioned up.
Lock plate:
1 pc.
Grounding plate:
1 pcs.
Parts included
Connecting plate:
1 pc.
Screw A (M4 x 6):
4 pcs.
Screw E (M4 x 7):
4 pcs.
Screw C (M4 x 18):
5 pcs.
Screw D
(M4 x 18 with rosette):
1 pc.
Screw B (M4 x 10):
2 pcs.
Staple unit:
1 pc.
Exit tray:
1 pc.
Staple cartridge: 1 pc.
Staple position label:
1 sheet
punch position label:
1 sheet
Front cover:
1 pc.
"OFF"
Actuator
Screw
Screw C
Screw D
Exterior
securing screw
securing screw
Screws C
Grounding plate
Lock plate
<1>
<2>
<3>
AR-F13 UNPACKING AND INSTALLATION 3-2
4) Attach the staple unit to the finisher.
<1> Open the front cover of the saddle finisher.
<2> Remove the two pieces of packing tape from the staple unit.
<3> Hold the handle and the bottom side of the staple unit, and
insert the unit into the saddle finisher.
<4> Close the front cover of the saddle finisher.
5) Attach the front cover to the saddle finisher.
<1> Put the plate R to the saddle finisher so that marking R is
positioned up and then secure the plate with two screws A.
<2> Put the front cover to the saddle finisher as shown in the illus-
tration and secure the cover with two screws B at the upper
part and two screws A at the lower part (four screws in total).
part and two screws A at the lower part (four screws in total).
6) Attach the exit tray to the saddle finisher.
<1> Put the two pawls of the exit tray onto the saddle finisher.
<2> Secure the exit tray with four screws E.
At this time, ensure that the positioning dowel is securely
inserted.
inserted.
7) Attach the connecting plate to the saddle finisher.
<1> Insert the connecting plate into the sheet metal at the lower
part of the saddle finisher.
<2> Secure the connecting plate to the saddle finisher with two
screws A.
Packing tape
Packing tape
Screws A
Screws B
Front cover
Screws A
Plate R
Pawl
Pawl
Screws E
Positioning dowel
Connecting plate
Screws A
AR-F13 UNPACKING AND INSTALLATION 3-3
8) Connect the saddle finisher to the main unit.
<1> Move the saddle finisher toward the left (exit area) of the main
unit.
<2> Position the connecting plate that has been attached to the
saddle finisher to the two holes at the lower left of the
optional stand, and secure it with two screws C.
optional stand, and secure it with two screws C.
At this time, attach the rear screw to the hole with marking C.
9) Adjust the height of the saddle finisher.
<1> Move the saddle finisher close to the main unit.
<2> Ensure that the guide pin of the lock plate that has been
attached to the duplex bypass/inverter unit is inserted
smoothly into the connecting hole of the saddle finisher.
smoothly into the connecting hole of the saddle finisher.
∗
If the guide pin should not inserted smoothly, adjust it using the pro-
cedure described below.
cedure described below.
A. If the connecting hole of the saddle finisher is deviated from the
guide pin of the lock plate:
<1> Loosen the two adjusting part securing screws at the rear of
saddle finisher stand section.
<2> Turn the rear height adjusting handle so that the height of the
guide pin matches with the height of the center of the con-
necting hole.
necting hole.
<3> Loosen the two adjusting part securing screws at the front of
the saddle finisher stand section.
<4> Turn the front height adjusting handle so that the height of
the top of the rib on the front cover matches with the height of
the top of the stand.
the top of the stand.
<5> Tighten the adjusting part securing screws (two for each of
front and rear).
<6> Carry out work B. (next page)
B: If the connecting hole of the saddle finisher matches with the guide
pin of the lock plate:
<1> Push the saddle finisher toward the main unit.
<2> Check the clearance between the saddle finisher and the
main unit at the upper and lower parts.
• If clearance A is not equal to clearance B:
<1> Remove the four screws that secure the cover of the saddle
finisher stand and remove the cover.
<2> Loosen the adjusting part securing screws (two for each of
front and rear).
<3> Turn the height adjusting screws (one for each of front and
rear) respectively so that clearance A becomes equal to
clearance B.
clearance B.
<4> Check that clearance A and clearance B are uniform both at
the front and at the rear.
<5> Tighten the adjusting part securing screws (two for each of
front and rear).
Screws C
Connecting plate
Optional stand
C
Guide pin
Adjusting
hole
hole
Height adjusting handles
Adjusting part securing screws
Adjusting
part securing
screws
part securing
screws
Front side
Rear side
Continued to the next page
Main unit
Stand
Front cover
Rib
Clearance A
Clearance B
Cover
Screw
Screw
Screw
Screw
Adjusting part
securing screws
securing screws
Adjusting part
securing screws
securing screws
Front side
Rear side
Height adjusting
screws
screws
Click on the first or last page to see other AR-F13 (serv.man2) service manuals if exist.