Sharp AR-F11 (serv.man7) Service Manual ▷ View online
6-44
CHAPTER 6 MECHANICAL CONSTRUCTION
2) Disconnect the connector [4] of the finisher.
3) Remove 4 screws [5], and take off the rear
3) Remove 4 screws [5], and take off the rear
cover [6].
B.
Feeding Section
1.
Removal of empty sensor
1) Remove the upper cover.
2) Remove 1 screw [1], disconnect 1 connec-
2) Remove 1 screw [1], disconnect 1 connec-
tor [2], and take off the empty sensor [3]
with the bracket.
with the bracket.
3.
Removal of rear cover
1) Remove 1 screw [1], cut off the bundled
wire band [2], and take off the sub cover
[3].
[3].
[2]
[1]
[3]
Figure 6-404
[6]
[5]
[5]
[4]
Figure 6-405
[1]
[2]
[3]
Figure 6-406
6-45
CHAPTER 6 MECHANICAL CONSTRUCTION
4) Catch the latch [6] of each roller and move
it sideways. Then take off the pickup roller
[7], feed roller [8] and separation roller [9].
[7], feed roller [8] and separation roller [9].
2.
Removal of pickup/feed/
separation rollers
separation rollers
1) Remove the empty sensor.
2) Remove 1 screw [1], and take off the feed
2) Remove 1 screw [1], and take off the feed
guide [2].
3) Lift the feed tray [3], remove 1 screw [4],
and take off the maintenance cover [5].
[2]
[1]
Figure 6-407
[3]
[4]
[5]
Figure 6-408
[7]
[6]
[8]
[9]
Figure 6-409
6-46
CHAPTER 6 MECHANICAL CONSTRUCTION
3.
Reverse solenoid/Pickup trigger
solenoid
solenoid
1) Remove the front cover.
2) Remove 1 screw [1], and take off the re-
2) Remove 1 screw [1], and take off the re-
verse solenoid [2].
3) Remove 2 screws [3], and take off the pickup
solenoid [4] with the bracket.
Figure 6-412
Figure 6-410
Figure 6-411
[3]
[4]
[3]
[1]
[2]
C.
Drive Section
1.
Feed motor/Transport motor/
Board
Board
1) Remove the rear cover.
2) Release 1 harness clamp [1], disconnect 1
2) Release 1 harness clamp [1], disconnect 1
connector [2], remove 2 screws [3], and take
off the fan motor [4].
off the fan motor [4].
[1]
[2]
[3]
[4]
6-47
CHAPTER 6 MECHANICAL CONSTRUCTION
3) Release 1 harness clamp [4], disconnect 1
connector [5], remove 3 screws [6], and take
off the feed motor [7] with the bracket.
off the feed motor [7] with the bracket.
4) Disconnect 14 connectors [8], remove 4
screws [9], and take off the main board [10].
5) Release 5 harness clamps [11], remove 7
screws [12], and take off the board bracket
[13].
[13].
Figure 6-415
Figure 6-414
Figure 6-413
[6]
[5]
[4]
[6]
[7]
[8]
[8]
[8]
[8]
[10]
[8]
[9]
[9]
[11]
[12]
[12]
[13]
Click on the first or last page to see other AR-F11 (serv.man7) service manuals if exist.