Sharp AR-F11 (serv.man7) Service Manual ▷ View online
6-4
CHAPTER 6 MECHANICAL CONSTRUCTION
6.
Removing the Tray 1 Unit
1) Open the upper cover and remove the end
caps [1].
2) Remove the prop upper cover [2] and the
prop lower cover [3].
Figure 6-108
5.
How to Lower the Tray 1/2 Unit
1) Insert a screwdriver or similar object into the
hole [2] while supporting the tray assembly
[1].
[1].
2) Release the tray lift motor one-way gear, and
lower the tray 1/2 unit.
Figure 6-107
[1]
[2]
[1]
[2]
[3]
3) Remove the harness [1] from the bracket [2].
4) Disconnect the three connectors [3]. Re-
4) Disconnect the three connectors [3]. Re-
move the screw [4], and remove the bracket.
5) Lift the tray 1 unit to remove.
[3]
[4]
[2]
[1]
Figure 6-109
6-5
CHAPTER 6 MECHANICAL CONSTRUCTION
7.
Removing the Tray 2 Unit
1) Remove the tray 1 unit.
2) Disconnect the two connectors [1] and
2) Disconnect the two connectors [1] and
grounding wire [2] and remove harness [3].
3) Lift the tray 2 unit to remove.
Figure 6-110
[1]
[2]
[3]
8.
Removing the Tray 1/2 Lift Motor
1) Remove the tray 1/2.
2) Remove two screws [1], and two lift blocks
2) Remove two screws [1], and two lift blocks
[2].
3) Remove the five screws [3], and remove the
tray from the tray unit.
Figure 6-111
[3]
[3]
[1]
[2]
[2]
3) Release the two harness stops [1].
Remove the four screws [2], and remove the
tray frame [3]. Release the claws [4] to re-
move.
tray frame [3]. Release the claws [4] to re-
move.
Figure 6-112
[2]
[3]
[2]
[4]
[4]
[1]
6-6
CHAPTER 6 MECHANICAL CONSTRUCTION
4) Disconnect the connector [1], and remove
the two screws [2].
Figure 6-113
[2]
[1]
5) Pull out the motor slightly, and remove the
parallel pin [1] and the motor.
Figure 6-114
[1]
Figure 6-115
9.
Removing the Grate-Shaped
Upper Guide
Upper Guide
1) Remove the slide guide [1] and end caps [2].
2) Release the tray lift motor gear clutch [6]
2) Release the tray lift motor gear clutch [6]
with a screwdriver or similar object while
supporting the tray assembly, and gently
lower the tray assembly down to its lowest
position.
supporting the tray assembly, and gently
lower the tray assembly down to its lowest
position.
3) Remove the five screws [3] (M4).
4) Remove the screw [4] (M3), and remove the
4) Remove the screw [4] (M3), and remove the
grate-shaped upper guide [5].
[1]
[5]
[3]
[4]
[6]
[2]
[2]
[3]
6-7
CHAPTER 6 MECHANICAL CONSTRUCTION
10. Removing the Grate-Shaped
Lower Guide
1) Remove the tray assembly.
2) Remove the five screws [1] (M4), and re-
2) Remove the five screws [1] (M4), and re-
move the front sub-support [2].
3) Remove the three screws [3] (M4).
4) Remove the three screws [4] (M3), and open
4) Remove the three screws [4] (M3), and open
the grate-shaped lower guide [5] to the front.
Figure 6-116
4) Free the harness [9] from the harness stop
[8].
5) Disconnect the two connectors [10], and re-
move the grate-shaped lower guide [7].
Figure 6-117
[3]
[4]
[6]
[5]
[2]
[1]
[8]
[10]
[9]
[7]
Caution:
To remove a sub-support, remove the front
sub-support [2]. The rear sub-support [6]
is adjustable. If the rear sub-support [6]
has been removed, be sure to adjust the rear
sub-support screw to the marking at which
it was set prior to the removal, or adjust
parallelism referring to "11. Installing the
Rear Sub-Support."
sub-support [2]. The rear sub-support [6]
is adjustable. If the rear sub-support [6]
has been removed, be sure to adjust the rear
sub-support screw to the marking at which
it was set prior to the removal, or adjust
parallelism referring to "11. Installing the
Rear Sub-Support."
Click on the first or last page to see other AR-F11 (serv.man7) service manuals if exist.