DOWNLOAD Sharp AR-DE9 (serv.man3) Service Manual ↓ Size: 1.95 MB | Pages: 47 in PDF or view online for FREE

6) Attach the rear cover.

●

Attach the rear cover to its original position and secure it with the
screw (M4 

× 12).

7) Return the copier to the normal orientation.

●

When returning the copier to the normal orientation, gently return
it without giving a shock.

8) Insert the DV cartridge into the copier.

●

Open the bypass tray, side cover, and front cover, and insert the
DV cartridge. Then, close the front cover, side cover, and bypass
tray.

9) Remove the paper tray lock for packing.

●

Remove the paper tray lock for packing that secures the turning
plate in the paper tray by rotating it in the direction of the arrow
and store it in the specified position.

10) Set the paper tray side guide.

●

Squeeze the lever of the paper tray side guide to slide the guide
to the position for the paper size to be used.

11) Load paper into the paper tray.

●

When loading paper, do not exceed the maximum height line.

12) Remove the optical locking screw and fusing unit packing lever so

that the copier is ready.

13) Insert the power plug into the outlet and turn the main switch to

the  “ON” position. Then, perform the following procedure.

14) Perform SIM setting.

●

Execute simulation [3] of [26] and enter [1].

15) Check the center displacement.

●

Place an original on the document glass and make a copy using
the tray in the copier.
Then, make a copy using the tray in the installed optional paper
feed unit.
If the center of the copy from the optional paper feed unit is dis-
placed from the copy from the tray in the copier, adjust the cen-
ter referring to the service manual.

1

2

3

Paper guide (A)

Paper guide (B)

AR-SP3

2  –  7

Turn the main switch to the “OFF” position and remove the power plug
from the outlet.

1) Remove the cover of the rear cabinet.

●

Remove the screw, slide the cover in the direction indicated by
the arrow, and remove the cover of the rear cabinet.

2) Remove the PWB cover.

<1> Loosen the screws that secure the PWB cover.
<2> Push up the PWB cover and
<3> Rotate it counterclockwise to remove it.

3) Attach the GDI interface PWB.

●

Fit the connector of the GDI PWB into the mounting position of
the copier, secure the side A with three screws, and then secure
the front B with two screws.

4) Attach the GDI harness.

●

Attach the GDI harness so that the blue lines face forward and
also face toward the GDI interface side.

Note: Be careful about the direction of the blue lines.

5) Attach the PWB cover.

<1> Before attaching the PWB cover, hold down the GDI harness

in the direction A in the illustration below.

<2> Fit the upper part of the PWB cover to the upper screw that

has been loosened in step 2 above.

<3> While rotating the lower part of the PWB cover clockwise, fit

it to the lower screw.

<4> Tighten the upper and lower screws to secure the cover.

2

1

1

3

M3X8

M3X8

AR-SP3

2  –  8

6) Attach the rear cover.

●

Align the arrow marks as shown in the illustration and then slide
the cover to the left. Then, secure the cover with a screw.

The printer driver is the software program which runs the printer. It con-
verts the data in your file into information that the printer can under-
stand. It also controls communication between the printer and
computer as the data is printed.

You will need the following hardware and software in order to install the
printer driver.

Computer 

type

IBM PC/AT or compatible computer
equipped with a bi-directional parallel or
USB interface, and CD-ROM drive

Windows type

Windows 3.1x, Windows 95, Windows 98*,
Windows NT 4.0
∗ USB is supported on Windows 98
preinstalled only.

CPU

486DX 66 MHz or better

Physical RAM

Windows 95, Windows 3.1x: 8MB (16MB or
more is recommended.)
Windows NT4.0: 12MB (16MB or more is
recommended.)
Windows 98: 16MB (32MB or more is
recommended.)

Display

640 

× 480 dots (VGA) or better

Hard disk free space

10 MB or more

Caution: The printer driver included in this product cannot be used

under Windows NT3.5x, OS/2, pure MS-DOS and other
operating systems which are not described above.

The software for your printer is provided on CD-ROM.
Before installing the printer driver, be sure to check the following items.

●

Is the printer connected properly to the computer?

●

Does the printer have paper?

●

Is there another GDI printer driver or Windows Printing System
printer driver already installed? If installed, change the printer
port setting. To change the printer port settings.

In this description, the following drive configuration is presumed.
Specify proper drives depending on the configuration of your computer.

Drive 

R:

CD-ROM drive (installation source). If necessary,
replace R with the letter of your CD-ROM drive.

Drive C:

Hard disk drive (installation destination). If necessary,
replace C with the letter of your hard disk drive.

a. Windows 95/Windows NT 4.0 Installation Instructions:
With both the computer and the printer turned off, connect the printer
to the computer with a parallel interface cable.

1) Load paper into the paper tray of the printer. For instructions on

loading paper, see the section LOADING COPY PAPER in the
copier operation manual.

2) Turn on the printer.

3) Turn on your computer and start Windows.

4) When using Windows 95 on a personal computer with plug & play*,

the “Update Device Driver Wizard” window will appear. Insert the in-
stallation CD-ROM into the CD-ROM drive. Click the Next button
and follow the on-screen instructions. Proceed to step 7. If the
“Copying Files” window appears during this operation, enter R:\ (if
the CD-ROM is designated as drive R) and click the OK button.

●

If you use Windows 95 and the “New Hardware Found” window
will appear, click the Driver from Disk Provided by Hardware
Manufacturer button and then click OK. Proceed to step 6.

●

If you use Windows 95 and the screen shown above or the “New
Hardware Found” window does not appear, proceed to step 5.

●

If you use Windows NT 4.0, proceed to step 5.

∗ Plug & play
This feature is effective if both the computer and peripheral equip-
ment are equipped with IEEE 1284 compliant parallel interface.

5) Insert the installation CD-ROM into the CD-ROM drive.

Click the Start button and select Run. When the screen shown
below appears, type R:\SETUP (if the CD-ROM is designated as
drive R) and click the OK button. Proceed to step 7.

Arrow marks

After sliding

AR-SP3

2  –  9

 6) “Install from Disk” window will appear. Insert the installation CD-

ROM into the CD-ROM drive. Type R:\ (if the CD-ROM is desig-
nated as drive R) and click the OK button. Proceed to step 7.

  7) The installation program will start. To install the printer driver to

the default folder, click the Next button. To select a different folder,
select Browse or type in the new path and folder name. Click OK
and say YES to create the folder, select the Next button to con-
tinue.

  8) On the display, you will see “printer port to be used”. Normally, this

is LPT1 and it is selected automatically.
Ensure that Yes is checked to use the printer as the default
printer.
Finally click the Next button.

 9) A “Confirm installation” window will be displayed. To continue in-

stallation, click the Yes button.

10) When the installation is complete, you will be asked whether or not

to print a test page. If you wish to do so, click the Yes button. At
this time, ensure that paper is loaded in the paper tray.

11) If the test print completes successfully, click the Finish button.

“The installation of the SHARP AR-150 Series Software is com-
plete.” window will be displayed. Click the OK button.

b. Windows 98:
With both the computer and the printer turned off, connect the printer
to the computer with either a parallel or a USB interface cable.

1) Load paper into the paper tray of the printer. For instructions on

loading paper, see the section LOADING COPY PAPER found in
the copier operation manual.

2) Turn on the printer.

3) Turn on your computer and start Windows.

When using the USB interface:

●

Connect your personal computer and the printer using a USB in-
terface cable if you have not already done so.

●

When the “Add New Hardware Wizard” window appears, insert
the installation CD-ROM, click the Next button, follow the on-
screen instructions, and finally click the Finish button.

4) When using Windows 98 on a personal computer with plug & play*,

the “Add New Hardware Wizard” window will appear. Click the Next
button and follow the on-screen instructions.

●

If the “Add New Hardware Wizard” window does not appear,
proceed to step 8.

∗ Plug &play: For plug & play information

5) Select Search for the best driver for your device and click the Next

button.

6) Insert the installation CD-ROM into the CD-ROM drive. (If you are

using the USB interface, confirm that the installation CD-ROM is in
the CD-ROM drive.) Select the CD-ROM drive and click the Next
button.

7) Windows driver file search will find the device “SHARP AR-150

Series”. Click the Next button. Proceed to step 9.

8) Insert the installation CD-ROM into the CD-ROM drive. (If you are

using the USB interface, confirm that the installation CD-ROM is in
the CD-ROM drive.) Click the Start button and select Run. When
the window shown below appears, type R:\SETUP (if the CD-ROM
is designated as drive R) and click the OK button. Proceed to step
9.

AR-SP3

2  – 10