DOWNLOAD Sharp AR-DE9 (serv.man3) Service Manual ↓ Size: 1.95 MB | Pages: 47 in PDF or view online for FREE

9) The installation program will start. To select a different folder, select

Browse and type in the path and folder name where the printer
driver will be installed. Click OK and say YES to create the folder,
select the Next button to continue. To install the printer driver to the
default folder, click the Next button.

10) On the display you will see “printer port to be used”. The printer

port is selected automatically. If you are using the parallel inter-
face, this is LPT1. If you are using the USB interface, this is
LPT/USB1. Ensure that Yes is checked to use the printer as the
default printer. Finally click the Next button.

11) A  “Confirm installation” window will be displayed. To continue in-

stallation, click the Yes button.

12) When the installation is complete, you will be asked whether or not

to print a test page. If you wish to do so, click the Yes button. At
this time, ensure that paper is loaded in the paper tray.

13) If the test print completes successfully, click the Finish button.

“The installation of the SHARP AR-150 Series Software is com-
plete.” window will be displayed. Click the OK button.

c. Windows 3.1x:
With both the computer and the printer turned off, connect the printer
to the computer with a parallel interface cable.

1) Load paper into the paper tray of the printer. For instructions on

loading paper, see the section LOADING COPY PAPER in the
copier operation manual.

2) Turn on the printer and then start Windows on your computer.

3) Insert the installation CD-ROM into a CD-ROM drive.

4) Choose File from the Menu bar in Program Manager, and then

choose the Run... command.

5) Type R:\SETUP (if the CD-ROM is designated as drive R) in the

command line box and then click the OK button.

6) Select a directory to which the printer driver will be installed and

click the Next button. To install it to the default directory, click the
Next button.

7) A “printer port to be used” window will be displayed. Normally, LPT1

is automatically set.
Then ensure that Yes is checked to use this printer as the default
printer.

8) A  “Confirm installation” window will be displayed. To continue in-

stallation, click Yes.

9) When the installation is complete, restart Windows.

When the printer driver is installed, the SHARP AR-150 Series printer
driver group will be created. This group of software programs provides
the following functions:

a. Uninstall AR-150 Series
The printer driver can be uninstalled. If the driver is uninstalled, printing
can no longer be performed on the printer.
For proper uninstallation, be sure to use the SHARP uninstall program
of the printer driver group.

Readme
The latest information on the printer driver is included in this document.
Read the Readme first.

Advanced Settings
See help for Advanced Settings.

Status Monitor
The Status Monitor window provides visual information about the
printer state and current job.

DOS Emulation Setup

Status Monitor HELP
Assistance and information for Status Monitor.

DOS Emulation HELP
Assistance and information for DOS Emulation support.

Advanced Settings HELP
Assistance and information for Advanced Settings.

AR-SP3

2  – 11

The SPF (Single Path Feeder) is installed to the AL-1000/1200 as a standard provision, and it automatically copies up to 30 sheets of documents
of a same size. (Only one set of copies)

(1)

Pickup roller

(2)

Sheet of document for paper feed

(3)

Set detection ACT

(4)

Paper stopper

(5)

Document feed roller

(6)

Separation sheet

(7)

Paper entry sensor

(8)

PS roller D

(9)

Transport follower roller

(10) Paper exit roller

(11) Paper exit follower roller

(12) Document tray

SPID ON

PSW ON

MIRM rotation

MM rotation

CPFS ON

SPFM rotation

SPUS ON

Document set

Document set sensor

Document feed unit lamp ON

PPD ON

RRC ON

SPPD ON

POD ON

Copy start

The scanner is shifted
to the exposure position.

(Copier side)

Main motor rotation

Paper feed

Synchronization

(Transfer)

(Fusing)

(Document exit)

Paper transport

(Exposure)

In the zooming mode, the magnification ratio in the sub 
scanning direction (paper transport direction) is adjusted
by changing the document transport speed.

(Paper exit)

SPF motor rotation

Document feed

Document transport sensor

Document transport

(SPF side)

Time chart (Tray feed)

AR-SP3

3 – 1

a. When SPPD is ON (document remaining) when the power is turned on.
b. When SPPD is not turned ON within about 1.5 sec (at 100% copy) after starting the document feed operation.
c. When SPPD is not turned on within about 4.7 sec (at 100% copy) after turning on SPPD.
d. When the SPF document jam release door or the OC cover is opened during document transport (SPF motor rotating).

No.

Part name Ref.

A

Sensor PWB

B

Pickup solenoid

C

Clutch

D

Manual paper feed roller, pickup roller

E

Belt

F

SPF motor

G

Paper entry sensor

H

PS roller

I

Paper exit roller

Pickup unit removal
1) Remove three fixing pawls from the bottom of the machine.
2) Remove the front cover and the rear cover.

1) Remove the belt, the paper feed frame SP, and two harnesses.
2) Remove the pickup unit.

*

When installing the parts, be careful of the hole position of the paper
frame SP.

AR-SP3

3  –  2

1) Remove two screws from the bottom of the pickup unit.
2) Remove the upper cover.

1) Remove two screws.
2) Remove the sensor PWB.
3) Remove the harness.

1) Remove two screws.
2) Remove the pickup solenoid

*

When installing, hang iron core A on the solenoid arm.

1) Remove the E-ring.
2) Remove the pulley and bush.
3) Slide the bush in the arrow direction.
4) Lift the clutch, and 5) remove the clutch.

1) Remove the E-ring.
2) Remove the parts.

1) Lift the paper stopper.
2) Slide the takeup roller unit.
3) Slide the bush in the arrow direction.
4) Remove the takeup roller unit.

AR-SP3

3  –  3