Sharp AR-C262M (serv.man3) Service Manual ▷ View online
AR-C262M DESCRIPTIONS OF EACH SECTION 7 - 56
Step 62:
Document feed motor (DFM) reverses
direction.
(Resist rollers rotate.)
Original is sent to the transport section.
direction.
(Resist rollers rotate.)
Original is sent to the transport section.
Step 63:
Document exit sensor (DES) detects the
leading edge of the discharged original.
(DES output HIGH)
leading edge of the discharged original.
(DES output HIGH)
Step 64:
Original timing sensor (TIMS) detects the
trailing edge of the original.
(TIMS output LOW)
trailing edge of the original.
(TIMS output LOW)
Step 65:
Document feed motor (DFM) OFF.
(Resist rollers stop.)
(Resist rollers stop.)
Step 66:
Transport feed motor (DTM) OFF.
(Transport belt stops.)
Original stops.
(Transport belt stops.)
Original stops.
Step 67:
Copier mirror base scanning starts.
Step 68:
Delivery motor (DEM) rpm decrease.
Step 69:
Document exit sensor (DES) detects the
trailing edge of the discharged original.
(DES output LOW)
Original discharged.
trailing edge of the discharged original.
(DES output LOW)
Original discharged.
Step 70:
Delivery motor (DEM) OFF.
(Reverse roller stops.)
(Reverse roller stops.)
*B <EMPS output>
LOW (original in tray)
→
Go to step 22 (preliminary
feed).
feed).
HIGH (no original in tray)
→
After completion of mirror base
scanning, go to step 29.
scanning, go to step 29.
(Discharge)
Step 71:
Transport motor (DTM) and delivery motor
(DEM) forward rotation.
(Transport belt and reverse roller rotate.)
(DEM) forward rotation.
(Transport belt and reverse roller rotate.)
Step 72:
Reverse solenoid (DRSOL) ON.
(Flapper descends.)
(Flapper descends.)
Step 73:
Document exit sensor (DES) detects leading
edge of original.
(DES output HIGH)
edge of original.
(DES output HIGH)
Step 74:
The Documentleading edge of the original
advances in the reverse direction by means of
the flapper.
advances in the reverse direction by means of
the flapper.
Step 62
Step 63
Step 64
Step 65
Step 66
Step 68
Step 69
Step 70
Step 71
Step 72
Step 73
Step 74
AR-C262M DESCRIPTIONS OF EACH SECTION 7 - 57
Step 75:
Reverse sensor (DRS) detects the leading
edge of the original.
(DRS output HIGH)
edge of the original.
(DRS output HIGH)
Step 76:
Reverse solenoid (DRSOL) OFF.
(The flapper ascends when the original rear
edge passes.)
(The flapper ascends when the original rear
edge passes.)
Step 77:
Transport motor (DTM) OFF.
(Transport belt stops.)
(Transport belt stops.)
Step 78:
Delivery motor (DEM) OFF.
(Reverse roller stops.)
(Reverse roller stops.)
Step 79:
Transport motor (DTM) reverses direction.
(Transport belt rotates.)
(Transport belt rotates.)
Step 80:
Transport motor (DEM) forward rotation.
(Reverse roller rotates.)
Original is transported towards the feed
section.
(Reverse roller rotates.)
Original is transported towards the feed
section.
Step 81:
Document exit sensor (DES) detects trailing
edge of reversed original.
(DES output LOW)
edge of reversed original.
(DES output LOW)
Step 82:
Reverse sensor (DRS) detects trailing edge of
reversed original.
(DRS output LOW)
reversed original.
(DRS output LOW)
Step 83:
Delivery motor (DEM) OFF.
(Reverse roller stops.)
(Reverse roller stops.)
Step 84:
Transport motor (DTM) OFF.
(Transport belt stops.)
(Transport belt stops.)
Step 85:
Transport motor (DTM) and delivery motor
(DEM) forward rotation.
(Transport belt and reverse roller rotate.)
(DEM) forward rotation.
(Transport belt and reverse roller rotate.)
Step 86:
Document exit sensor (DES) detects leading
edge of discharged original.
(DES output HIGH)
edge of discharged original.
(DES output HIGH)
Step 75
Step 76
Step 77
Step 78
Step 79
Step 80
Step 81
Step 82
Step 83
Step 84
Step 85
Step 86
AR-C262M DESCRIPTIONS OF EACH SECTION 7 - 58
NOTES:
*A: This operation is performed when there is an original already on the original platform in advance. If there is no original on the original
platform, this operation is not performed.
*B: When there is an original in the original tray, the original set sensor (EMPS) output becomes LOW.
*C: Performance of this operation depends on whether there was any preliminary feed in steps 22 to 28.
B. Disassembly/assembly/maintenance
(1) Maintenance target parts in the RADF section
✕
: Check (Clean, replace, or adjust as necessary.)
❍
: Clean
▲
: Replace
∆
: Adjust
✩
: Lubricate
❏
: Shift position
*1: When to replace: Check the counter value on the respective feed entrances.
Roller/pad parts: 100K or 2 years.
(2) Replacement procedures of maintenance parts and major parts
[Separation section]
a. Pickup roller and document feed roller
1) Open the document feed cover.
a-1. Pickup roller and document feed roller disassembly
1) Open (A) the document feed cover.
2) Press the tab, and remove (B).
Step 87:
Delivery motor (DEM) rpm decrease.
Step 88:
Transport motor (DTM) OFF.
(Transport belt stops.)
(Transport belt stops.)
Step 89:
Document exit sensor (DES) detects trailing
edge of discharged original.
(DES output LOW)
edge of discharged original.
(DES output LOW)
Step 90:
Original is discharged.
Step 91:
Delivery motor (DEM) OFF.
(Reverse roller stops.)
(Reverse roller stops.)
END
Step 87
Step 88
Step 89
Step 90
Step 91
Part name
When
calling
50K
100K
150K
200K
250K
300K
350K
400K
Remarks
Separation
section
section
1
Pickup roller
(
❍
)
✕
❍
❍
❍
❍
❍
❍
❍
❍
*1
2
Document feed roller
(
❍
)
✕
❍
❍
❍
❍
❍
❍
❍
❍
*1
3
Separation pad
(
❍
)
✕
❍
❍
❍
❍
❍
❍
❍
❍
*1
A
B
AR-C262M DESCRIPTIONS OF EACH SECTION 7 - 59
3) Detach the tab, and remove (C) arm F.
4) Remove (D) the pickup roller.
5) Remove (E) the separation roller.
b. Separation pad
1) Open the document feed cover.
b-1. Separation pad disassembly
1) Remove the screws.
2) Press the tab, and remove (A) the forward separation rubber
cover.
3) Remove (B) the separation pad.
[Transport section]
✕
: Check (Clean, replace, or adjust as necessary.)
❍
: Clean
▲
: Replace
∆
: Adjust
✩
: Lubricate
❏
: Shift position
a. Original transport belt
a-1. Original transport belt unit disassembly
1) Loosen the screws.
2) Remove (A) the original transport belt unit.
C
D
E
A
B
B
Part name
When
calling
50K
100K
150K
200K
250K
300K
350K
400K
Remarks
Transport section
4
Transport belt
(
❍
)
✕
❍
❍
❍
❍
❍
❍
❍
❍
A
Click on the first or last page to see other AR-C262M (serv.man3) service manuals if exist.