DOWNLOAD Sharp AR-C262M (serv.man3) Service Manual ↓ Size: 34.72 MB | Pages: 127 in PDF or view online for FREE

AR-C262M  DESCRIPTIONS OF EACH SECTION  7 - 64

3) Remove the resist roller.

When mounting the bearing, insert it while pushing in the direc-
tion of arrow A.

1) Open (A) the document feed cover and (B) the reverse cover.

2) Remove the screws, and remove (C) the rear cover.

1) Detach the connector.

2) Remove the screws, and remove (A) the harness guide.

3) Remove the screws, and remove the transport motor unit.

4) Remove the screws, and remove (B) transport motor.

The belt should pass below (C).

1) Raise the RADF main body.

2) Remove the screws, and remove (A) the document exit

bracket.

A

A

B

C

B

A

C

A

AR-C262M  DESCRIPTIONS OF EACH SECTION  7 - 65

3) Remove the screws, detach the connect, and take out (B) the

document exit sensor unit.

4) Remove all parts, and remove (C) the document exit sensor.

1) Remove the original transport belt unit.

2) Detach the connector.

3) Remove the front cover.

4) Remove each screw, and remove (A) the reverse solenoid.

1) Detach each connector.

2) Remove the screws, and remove (A) the reverse unit.

(1) Remove the screws, and remove (A) the reversing motor.

1) Remove the screws, and remove (A).

2) Detach the connector, and remove (B) the document exit

cover open sensor.

C

B

A

A

A

B

A

AR-C262M  DESCRIPTIONS OF EACH SECTION  7 - 66

1) Detach the connector.

2) Remove the screws, and remove (A) the ADF open SW.

1) Loosen the screws.

2) Remove the screws, and remove the E-ring.

3) Remove (A).

4) Remove the E-ring.

5) Remove (B) the reverse roller.

1) Remove the rear cover.

2) Detach the connector, remove the screws, and remove the

main PWB.

1) Remove the front cover.

2) Remove the screws, and remove the LED PWB.

A

A

B

A

A

AR-C262M  SETTING AND ADJUSTMENTS  8 - 1

Each adjustment item in the adjustment item list is indicated with its JOB number.
Perform the adjustment procedures in the sequence of Job numbers from the smallest to the greatest.
However, there is no need to perform all the adjustment items. Perform only the necessary adjustments according to the need.
Unnecessary adjustments can be omitted. Even in this case, however, the sequence from the smallest to the greatest JOB number must be
observed.
If the above precaution should be neglected, the adjustment would not complete normally or a trouble may occur.

∗

1: By executing the collective adjustment of image position and magnification ratio (ADJ21) (Automatic void adjustment SIM50-28), the

adjustments of SIM50-10, 48-1, 50-12, and 50-1 can be simply and automatically performed at once.

JOB No

ADJUSTMENT ITEM LIST

SIMULATION

ADJ 1

High voltage adjustment

ADJ 1A

Main charger grid voltage adjustment

8-2

ADJ 1B

DV bias voltage adjustment

8-1

ADJ 1C

Transfer voltage adjustment

8-6

ADJ 2

Image density sensor adjustment

ADJ 2A

Color image density sensor adjustment (adjustment by the 
adjustment jig)

44-13

ADJ 2B

Black image density sensor adjustment

44-2

ADJ 3

Image focus, image skew adjustment (LED (writing) unit)

64-1/61-4

ADJ 4

Image registration adjustment

ADJ 4A

Image registration adjustment (Auto adjustment)

50-22

ADJ 4B

Image registration adjustment (Manual adjustment)

50-20

ADJ 5

Image position/print area adjustment 
(Print engine section)

ADJ 5A

Main scanning direction image position adjustment 
(Print engine section)

50-10

ADJ 5B

Sub scanning direction image position/print area adjustment 
(Print engine section)

50-5

ADJ 6

Copy image distortion adjustment

ADJ 6A

Scanner (reading) unit parallelism adjustment

ADJ 6B

Copy image sub scanning direction distortion adjustment

ADJ 6C

Copy image main scanning direction distortion adjustment

ADJ 6D

Scan image distortion adjustment

ADJ 7

Copy image focus (main scanning direction copy magnification ratio) adjustment (CCD unit position adjustment)

48-1

ADJ 8

Sub scanning direction copy magnification ratio adjustment

48-1

ADJ 9

Main scanning direction copy image position adjustment (Scanner (reading) section)

50-12

ADJ 10 Copy image position/image loss/void area adjustment

50-1/50-2

ADJ 11 Copy color balance/density 

adjustment

ADJ 11A CCD gamma adjustment (CCD calibration)

(Normal document copy mode)

63-3 (63-5)

ADJ 11B Copy color balance adjustment (Auto adjustment)

46-24

ADJ 11C Copy color balance adjustment (Manual adjustment)

46-21

ADJ 11D Copy density adjustment in low-density area

(Normally unnecessary to adjust.)

46-1/2

ADJ 11E Copy color balance density adjustment (each copy mode)

(Normally unnecessary to adjust.)

46-10 to 16

ADJ 11F CCD gamma adjustment (CCD calibration)

(Copy document copy mode)

63-9

ADJ 11G Image edge section gamma/density adjustment 

(Black text and black line reproduction adjustment) (Normally 
unnecessary to adjust.)

46-27

ADJ 11H Copy color balance adjustment (Single color Copy mode)

(Normally unnecessary to adjust.)

46-25

ADJ 11I

Auto color balance adjustment by user (Copy color balance 
auto adjustment enable setting and adjustment)

26-53

ADJ 11J Background process conditions setting in the color auto copy 

mode, image auto recognition conditions setting, text-on-dot 
recognition conditions setting, filter setting

46-33

ADJ 12 Fusing pressure adjustment
ADJ 13 Fusing paper guide position adjustment
ADJ 14 Document size sensor adjustment

ADJ 14A Original size sensor detection point adjustment

41-2

ADJ 14B Original size sensor sensitivity adjustment

41-2

ADJ 15 Manual paper feed tray paper size sensor adjustment

40-2

ADJ 16 Touch panel coordinates setting

65-1

ADJ 17 Power voltage adjustment

ADJ 17A 3.4 V power voltage adjustment
ADJ 17B 5.0 V power voltage adjustment

ADJ 18 FAX/scanner mode image loss adjustment

50-27

ADJ 19 RADF adjustment

ADJ 19A ADF adjustment (skew adjustment)
ADJ 19B Magnet adjustment
ADJ 19C Solenoid adjustment
ADJ 19D ADF open position adjustment

ADJ 20 Printer color balance adjustment

ADJ 20A Printer automatic color balance adjustment

67-24

ADJ 20B Printer color balance adjustment (By the key operator program)

ADJ 21 Collective adjustment of image 

position and magnification ratio

(

∗

1)

50-28