DOWNLOAD Sharp AR-C200P (serv.man4) Service Manual ↓ Size: 6.27 MB | Pages: 127 in PDF or view online for FREE

AR-C200P   Rev.5 

105 /

  

3.4.2.3 Sensitivity Adjustment

(1) With the press of OK on the ADJUSTMM screen, sensitivity adjustment is performed.  The

printer boots up, and four sheets of media are passed through it.

(2) When the sensitivity adjustment is completed properly, the ADJUSTMM screen and the

Adjust Munsell & Media screen are displayed.

(3) When the sensitivity adjustment is not properly completed, the screen appears.  In such

cases, see Actions for NG Sensitivity Adjustment.

(4) The folder C:\MediaThickness is automatically created, storing the result of the sensitivity

adjustment in the CSV format.
Determine cause(s) of NG results from the stored file.  After the cause(s) are corrected,
conduct sensitivity adjustment again.

(5) Power off the printer and disconnect the interface cable.

AR-C200P   Rev.5 

106 /

  

3.4.2.4 Actions for NG Sensitivity Adjustment

When a CSV format file stored automatically in sensitivity adjustment is opened, the opened file
contains the following.  The yellow-shaded area shows errors.  For error code-to-description
correspondence, see the flow chart shown below.

Data stored in CSV format (Example)

Calibration of Media-thickness adjustment & Munsell correction writing

#####

IR Number

17
18
37

1

13

5

Err.Code

0
0
0
0
0
0

Check Input

101

99
96

101
101
102

Check Meas

107
103
100
105
105

98

Calb

141
146
145
139
136
140

Data-D1

101
100
103

98
98

101

Data-D2

103
102
101

99

103
104

Data-D3

102
103
101
103
104
101

Data-R1

99
97

101

98
91
97

Data-R2

105
108
109

98

100
106

Data-R3

104
112
107
102
104
102

AD-1

754
627
640
772
687
752

AD-2

760
634
653
779
697
760

AD-3

762
634
654
781
698
759

AD-Che

763
633
654
781
697
758

Judg

GOOD
GOOD
GOOD
GOOD
GOOD
GOOD

Date

######
######
######
######
######
######

Time

8:55:06

10:14:21
10:18:42
10:38:15
10:45:58
10:58:27

Munsell

FE        
FE        

0
3
2
2

Lot:

0121 MO59970

Machin ODC-000

Error323/324

Error codes and Error descriptions

END

See Attachment

Adjustment Process

Sensitivity
adjustment performed

No

Yes

Check the height of the lever-magnification.

Yes

Yes

10

The paper

absence AD value not within

its spec.

20

The media thickness not within its spec.

No

No

Yes

Non-Paper AD Error

No

40

The difference between

the values in the presence and absence

of paper not within its spec.

50

A sensor faulty occurred

No

Replace the cover

Assy - thickness or

the plate Assy - stay.

Yes

Yes

Replace the sensor.

FE adjustment failed

No

Thickness Error

Slant Error

SNS AD Error

SNS Error

1

Check the height of the lever-magnification.

2

When a thicker value is detected, check the height of the
stage-pickup.

1

Check the height of the lever-magnification.

2

Check the sliding performance of the lever-pickup.

3

When a thinner value is detected, check the sliding
performance of the lever-magnification and the lever-pickup.

OK

NG

Go to the top of the flow.

30

The skew not within its spec.

Sensitivity

adjustment performed

OK or NG

1

This error may be caused by other factors, such as  paper
jamming, hopping and paper absence.

2

For paper jamming at media thickness detection part, adjust
the height of the stage-pickup.

Action procedure for NG sensitivity adjustment on media thickness detection part

AR-C200P   Rev.5 

107/

  

3.4.3

Inputting the density of the calibration chip for density detection

Write the calibration target adjustment value (last 2 digits in the barcode, refer to the figure below)
indicated on the shutter label.

The adjustment value of the shutter must be reset when Sheet Color, density sensor, or PU sensor
is replaced.

3.4.3.1 Density Adjustment Menu Setting

For the steps (1) to (8) of menu setting, see Media Thickness Detection Adjustment Calibration
3.4.2.1, steps (1) to (8).

(9) The screen returns to the Adjust Munsell & Media screen.  Press Munsell.

(10) Press Yes.

(11) The Munsell sheet correction value input screen appears.

AR-C200P   Rev.5 

108 /

  

(12) Enter the correction value marked on the barcode label on the shutter into the Input field

and press OK (the Munsell sheet correction value is sent from the PC to the printer and set).

(13) When the density adjustment is completed properly, the ADJUSTMM screen and the

Adjust Munsell & Media screen are brought up.

xxx.......xx FC

61mm

2-Character correction value

Code content

Barcode

6mm

Barcode specification:

1

 Applied code

: code39

2

 Barcode digit

: 12 digits

3

 Written content :

From the left:*1 digit

Date4 digits

(ID barcode) method
Year

1 digit - 1 digit (x) in (200x)

Month 1 digit (10th, 11th, 12th month are indicated as X, Y, Z.)
Day

2 digits

Empty 4 digits

Set zeros “0000”.

2 adjustment digits (Same as the data format input manually for the printer.)

00~04 for 0 to 4, FF~FC for -1 to -4.

4

 Barcode length

YC4116-1006P001 label sheet 1/4”