DOWNLOAD Sony MDS-JB920 Service Manual ↓ Size: 5.05 MB | Pages: 72 in PDF or view online for FREE

Model
MDS-JB920
Pages
72
Size
5.05 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
mds-jb920.pdf
Date

Sony MDS-JB920 Service Manual ▷ View online

MICROFILM
SERVICE MANUAL
MINI DISC DECK
US Model
Canadian Model
AEP Model
UK Model
SPECIFICATIONS
MDS-JB920
Model Name Using Similar Mechanism
MDS-JE520
MD Mechanism Type
MDM-5A
Optical Pick-up Type
KMS-260A/J1N
System
MiniDisc digital audio system
Disc
MiniDisc
Laser
Semiconductor laser (
λ
=780nm)
Emission duration: continuous
Laser output
Less than 44.6 
µ
W*
* This output is the value measured at a
distance of 200 mm from the objective lens
surface on the Optical Pick-up Block with 7
mm aperture.
Laser diode properties
Material: GaAIAs
Revolutions (CLV)
400 rpm to 900 rpm
Error correction
Advanced Cross Interleave Reed
Solomon Code (A CIRC)
Sampling frequency
44.1 kHz
Coding
Adaptive Transform Acoustic Coding
(ATRAC)
Modulation system
EFM (English-to-Fourteen Modulation)
Number fo channels
2 setero channels
Frequency response
5 to 20,000 Hz ±0.3 dB
Signal-to-noise retio
Over 100 dB during playback
Wow and flutter
Below measureble limit
U.S. and foreign patents licensed form Dolby Laboratories
Licensing Corporation.
Inputs
jack
input
Rated
Minimum
type
impedance
input
input
LINE (ANALOG) phono
47 kilohms
500 mVrms 125 mVrms
IN
jacks
DIGITAL
Square
Optical wave
OPTICAL IN1
optical
length:
       —
      —
connector
660 nm
jack
DIGITAL
Square
Optical wave
OPTICAL IN2
optical
length:
       —
      —
connector
660 nm
jack
DIGITAL
Phono
75 ohms
0.5 Vp-p
      —
COAXIAL IN
jack
±20%
Outputs
jack type
Rated output
Load impedance
PHONES
Stereo
28 mW
32 ohms
phone jack
LINE (ANALOG) Phono
2 Vrms
Over
OUT
jacks
(at 50 kilohms)
10 kilohms
DIGIRAL
Square
–18 dBm
Optical wave
OPTICAL OUT
optical
length:
connector
660 nm
jack
DIGITAL
Phono
0.5 Vp-p
75 ohms
COAXIAL OUT
jack
(at 75 ohms)
– 2 –
General
Power requirements
Where purchased
Power requirements
Continental Europe and UK
220 – 230 V AC, 50/60 Hz
U.S.A and Canada
120 V AC, 60 Hz
Power consumption
18 W
Dimensions (approx.) (w/h/d) incl.projecting parts and controls
430 
×
 107.5 
×
 287 mm
(17 
×
 4
1
/
4
 
×
 11
3
/
8
 in)
Mass (approx.)
4.8 kg (10 lb 9 oz)
Supplied accessories
Audio connecting cords (2)
Optical cable (1)
Remote commander (remote) RM-D17M (1)
R6 (size-AA) batteries (2)
Design and specifications are subject to change without notice.
SELF-DIAGNOSIS FUNCTION
The self-diagnosis function consists of error codes for customers which are displayed automatically when errors occur, and error codes
which show the error history in the test mode during servicing. For details on how to view error codes for the customer, refer to the
following box  in the instruction manual. For details on how to check error codes during servicing, refer to the following “Procedure for
using the Self-Diagnosis Function (Error History Display Mode)”.
Procedure for using the Self-Diagnosis Function (Error History Display Mode).
Note:
Perform the self-diagnosis function in the “error history display mode” in the test mode. The following describes the least required procedure. Be
careful not to enter other modes by mistake. If you set other modes accidentally, press the  MENU/NO  button to exit the mode.
1. While pressing the 
[        AMS        ]
 knob and  
p
  button, connect the power plug to the outlet, and release the 
[        AMS        ]
  knob
and  
p
  button.
2. Rotate the 
[        AMS        ]
 knob and when “[Service]” is displayed, press the 
[YES]
 button.
3. Rotate the 
[        AMS        ]
 knob and display “ERR DP MODE”.
4. Pressing the 
[YES]
 button sets the error history mode and displays “total rec”.
5. Select the contents to be displayed or executed using the 
[        AMS        ]
 knob.
6. Pressing the 
[        AMS        ]
 knob will display or execute the contents selected.
7. Pressing the 
[        AMS        ]
 knob another time returns to step 4.
8. Pressing the 
[MENU/NO]
 button displays “ERROR DP MODE” and exits the error history mode.
9. To exit the test mode, press the 
[REPEAT]
 button. The unit sets into the STANDBY state, the disc is ejected, and the test   mode ends.
[  ]
±
[  ]
±
±
±
±
±
±
– 3 –
Items of Error History Mode Items and Contents
Selecting the Test Mode
Display
Details of History
E00
No error
E01
Disc error. PTOC cannot be read
(DISC ejected)
E02
Disc error. UTOC error
(DISC not ejected)
E03
Loading error
E04
Address cannot be read (Servo has deviated)
Table of Error Codes
Error Code
Error Code
Details of Error
total rec
Displays the recording time.
Displayed as “rππππππh”.
The displayed time is the total time the laser is set to the high power state.
This is about 1/4 of the actual recording time.
The time is displayed in decimal digits from 0h to 65535h.
total play
Displays the play time.
Displayed as “pππππππh”. The time displayed is the total actual play time. Pauses are not counted.
The time is displayed in decimal digits from 0h to 65535h.
retry err
Displays the total number of retries during recording and number of retry errors during play.
Displayed as “rππ pππ”.
“r” indicates the retries during recording while “p” indicates the retry errors during play.
The number of retries and retry errors are displayed in hexadecimal digits from 00 to FF.
total err
Displays the total number of errors.
Displayed as “total ππ”.
The number of errors is displayed in hexadecimal digits from 00 to FF.
err history
Displays the 10 latest errors.
Displayed as “0π E@@”.
π indicates the history number. The smaller the number, the more recent is the error. (00 is the latest).
@@ indicates the error code.
Refer to the following table for the details. The error history can be switched by rotating the 
[        AMS        ]
knob.
er refresh
Mode which erases the “retry err”, “total err”, and “err history” histories.
When returning the unit to the customer after completing repairs, perform this to erase the past error history.
After pressing the 
[        AMS        ]
 button and “er refresh?” is displayed, press the 
[YES]
 button to erase the
history.
“Complete!” will be displayed momentarily.
Be sure to check the following when this mode has been executed.
• The data has been erased.
• The mechanism operates normally when recording and play are performed.
tm refresh
Mode which erases the “total rec” and “total play” histories.
These histories serve as approximate indications of when to replace the optical pickup.
If the optical pickup has been replaced, perform this operation and erase the history.
After pressing the 
[        AMS        ]
 button and “tm refresh?” is displayed, press the 
[YES]
 button to erase the
history.
“Complete!” will be displayed momentarily.
Be sure to check the following when this mode has been executed.
• The data has been erased.
• The mechanism operates normally when recording and play are performed.
±
±
±
E05
FOK has deviated
E06
Cannot focus (Servo has deviated)
E07
Recording retry
E08
Recording retry error
E09
Playback retry error
(Access error)
E0A
Playback retry error (C2 error)
Details of Error
– 4 –
SECTION  1
SERVICING  NOTES
SAFETY  CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE  TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able.  (See Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
0.15 
µ
F
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
MODEL IDENTIFICATION
— BACK PANEL —
Part No.
4-998-603-1 
π
AEP and UK models
4-998-603-3 
π
US model
4-998-603-4 
π
Canadian model
TABLE  OF  CONTENTS
1.
SERVICING  NOTES
...............................................
4
2.
GENERAL
................................................................... 11
3.
DISASSEMBLY
......................................................... 14
4.
TEST  MODE
.............................................................. 18
5.
ELECTRICAL  ADJUSTMENTS
......................... 23
6.
DIAGRAMS
6-1. IC Pin Function Description ........................................... 32
6-2. Block Diagram – SERVO Section – ............................... 41
6-3. Block Diagram – MAIN Section – ................................. 43
6-4. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 46
6-5. Printed Wiring Board  – BD Section – ........................... 47
6-6. Schematic Diagram – BD Section (1/2) – ...................... 49
6-7. Schematic Diagram – BD Section (2/2)– ....................... 51
6-8. Schematic Diagram – MAIN Section (1/3)– .................. 55
6-9. Schematic Diagram – MAIN Section (2/3)– .................. 57
6-10. Schematic Diagram – MAIN Section (3/3)– .................. 59
6-11. Printed Wiring Board
– MAIN Board (Side A) .................................................. 61
6-12. Printed Wiring Boards
– MAIN Board (Side B), AC/BAT Boards ..................... 63
6-13. Printed Wiring Boards
– PANEL Section – ......................................................... 65
6-14. Schematic Diagram  – PANEL Section – ....................... 67
6-15. Schematic Diagram
– BD SWITCH Section – ................................................ 69
6-16. Printed Wiring Board
– BD SWITCH Section – ................................................ 69
7.
EXPLODED  VIEWS
................................................ 75
8.
ELECTRICAL  PARTS  LIST
............................... 79
Page of 72
Display

Sony MDS-JB920 Service Manual ▷ Download

  • DOWNLOAD Sony MDS-JB920 Service Manual ↓ Size: 5.05 MB | Pages: 72 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony MDS-JB920 in PDF for free, which will help you to disassemble, recover, fix and repair Sony MDS-JB920 Audio. Information contained in Sony MDS-JB920 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.