Sharp AR-286 (serv.man10) User Manual / Operation Manual ▷ View online
8-27
CHAPTER
8
Disabling of Bypass-Tray When Offset Tray Selected
This program is used to disable the use of the bypass tray when the
offset tray is selected for the optional finisher (AR-FN2 only).
offset tray is selected for the optional finisher (AR-FN2 only).
To disable use of the bypass tray when the offset tray is
selected, press the “DISABLING OF BYPASS-TRAY WHEN
OFFSET TRAY SELECTED.” box to display a check mark.
To restore use of the bypass tray, press the checked box
again to clear the check mark.
selected, press the “DISABLING OF BYPASS-TRAY WHEN
OFFSET TRAY SELECTED.” box to display a check mark.
To restore use of the bypass tray, press the checked box
again to clear the check mark.
OTHER PROGRAMS
The following two programs are not included in the four categories. The
programs can be selected by pressing the relevant key on the touch
panel after the key operator program mode is selected.
programs can be selected by pressing the relevant key on the touch
panel after the key operator program mode is selected.
Total Count
This program is used to display the total counts, including counts of the copier,
document feeder, duplex module, and stapler.
An A3 (11" x 17") copy is counted as two copies.
Covers and transparency inserts are counted as one copy even if they are
blank.
The lists printed with the key operator programs are included in “OTHERS”.
When the “TOTAL COUNT.” key is pressed, the following display will appear.
document feeder, duplex module, and stapler.
An A3 (11" x 17") copy is counted as two copies.
Covers and transparency inserts are counted as one copy even if they are
blank.
The lists printed with the key operator programs are included in “OTHERS”.
When the “TOTAL COUNT.” key is pressed, the following display will appear.
The total counts for all units in use will be displayed.
To print these counts, press the “PRINT” key.
Press the “OK” key to exit the program.
To print these counts, press the “PRINT” key.
Press the “OK” key to exit the program.
Program List Printout
This program is used to print out the list of available key operator
programs.
programs.
Press the “PROGRAM LIST PRINTOUT.” key.
●
The copier will start printing. To stop printing after starting, press
the “CANCEL” key.
the “CANCEL” key.
KEY OPERATOR PROGRAMS
TOTAL COUNT.
COPIES
: 022,500
STAPLER
: 003,000
OTHERS
: 000,500
DOCUMENT :
012,000
FEEDER
DUPLEX
DUPLEX
: 007,500
PRINT
OK
KEY OPERATOR PROGRAMS
KEY OPERATOR’S GUIDE
Key operator programs
8-28
CHAPTER
8
KEY OPERATOR ASSISTANCE CALL
When the copier is in need of service or care not usually performed
by general users, the copier will stop and one of the following
messages listed below will appear.
by general users, the copier will stop and one of the following
messages listed below will appear.
Message
Remedy
CHECK STAPLER POSITION OR STAPLE JAM.
See page 7-12 (AR-FN1N) or 7-27 (AR-FN2) for staple jam
removal. If the trouble cannot be easily remedied, use key
operator program “DISABLING OF STAPLER” (page 8-
25) to prevent the use of the stapler.
Contact your authorised Sharp Service Centre for service.
removal. If the trouble cannot be easily remedied, use key
operator program “DISABLING OF STAPLER” (page 8-
25) to prevent the use of the stapler.
Contact your authorised Sharp Service Centre for service.
THE FINISHER IS OUT OF SERVICE.
Contact your authorised Sharp Service Centre for service.
PRESS [CA] TO CANCEL JOB.
(This message will appear when the optional finisher
(AR-FN1N, AR-FN2) malfunctions.)
(AR-FN1N, AR-FN2) malfunctions.)
DUPLEX SYSTEM IS OUT OF SERVICE.
Use key operator program “DISABLING OF DUPLEX
COPYING” (page 8-24) to prevent the use of the duplex
system. Contact your authorised Sharp Service Centre
for service.
COPYING” (page 8-24) to prevent the use of the duplex
system. Contact your authorised Sharp Service Centre
for service.
THE DOCUMENT FEEDER IS OUT OF SERVICE.
Use key operator program “DISABLING OF DOCUMENT
PRESS [CA] TO CANCEL JOB.
FEEDER” (page 8-24) to prevent the use of the
document feeder. Contact your authorised Sharp Service
Centre for service.
document feeder. Contact your authorised Sharp Service
Centre for service.
SELECTED PAPER TRAY IS OUT OF SERVICE.
Contact your authorised Sharp Service Centre for service.
PLEASE SELECT ANOTHER PAPER TRAY.
CALL FOR SERVICE. CODE:
With this message, an alphanumeric code will appear to
indicate a malfunction has occurred which cannot be
corrected by the key operator.
Contact your authorised Sharp Service Centre for service.
Be sure to report the alphanumeric code information as
well. This will enable the Service Centre to prepare to
correct the malfunction associated with the code.
indicate a malfunction has occurred which cannot be
corrected by the key operator.
Contact your authorised Sharp Service Centre for service.
Be sure to report the alphanumeric code information as
well. This will enable the Service Centre to prepare to
correct the malfunction associated with the code.
KEY OPERATOR’S GUIDE
Key operator assistance call
8-29
CHAPTER
8
KEY OPERATOR CODE NUMBER:
FACTORY SETTING
FACTORY SETTING
The following is the factory setting of the Key Operator Code
Number, which must be used to access the Key Operator
Program.
Number, which must be used to access the Key Operator
Program.
Factory setting = 00000
This number must be entered when accessing the Key
Operator Program for the first time. (See page 8-2.)
Operator Program for the first time. (See page 8-2.)
NOTE:
The Key Operator Code Number is an important security
number allowing the Key Operator to configure the copier’s
functions and auditor’s settings.
You should register your own code number — different from
the factory setting above — immediately after your copier is
installed.
The Key Operator Code Number is an important security
number allowing the Key Operator to configure the copier’s
functions and auditor’s settings.
You should register your own code number — different from
the factory setting above — immediately after your copier is
installed.
★ KEY OPERATOR
Detach this page and store it in a safe place.
✂✂✂✂✂
KEY OPERATOR’S GUIDE
Key operator code number: factory setting
99D DSC1
CINSE1855FC51
CINSE1855FC51
Click on the first or last page to see other AR-286 (serv.man10) service manuals if exist.