Sharp AR-286 (serv.man10) User Manual / Operation Manual ▷ View online
8-15
CHAPTER
8
Add or Change Extra Preset Ratios
Two extra preset copy ratios can be added within both the reduction
range (25% to 99%) and the enlargement range (101% to 800%). Only
added preset copy ratios can be changed. The standard preset copy
ratios are fixed in memory and cannot be changed.
When the “ADD OR CHANGE EXTRA PRESET RATIOS.” key is
pressed, the following display will appear.
range (25% to 99%) and the enlargement range (101% to 800%). Only
added preset copy ratios can be changed. The standard preset copy
ratios are fixed in memory and cannot be changed.
When the “ADD OR CHANGE EXTRA PRESET RATIOS.” key is
pressed, the following display will appear.
1.
Press a key under “REDUCTION” or “ENLARGEMENT”
on the touch panel.
on the touch panel.
●
The selected key will be highlighted.
2.
Use the
and
keys to set the desired copy ratio.
●
To decrease or increase the copy ratio rapidly, press and hold
the
the
or
key.
●
To add or change other extra preset copy ratios, repeat steps 1
and 2.
and 2.
●
To cancel an extra preset ratio, select the copy ratio and press
the CLEAR (
C
) key.
3.
Press the “OK” key.
Setting a Maximum Number of Copies
Use this program to limit the maximum number of copies per copy run
which can be input in the copy quantity display.
When the “SETTING A MAXIMUM NUMBER OF COPIES.” key is
pressed, the following display will appear.
which can be input in the copy quantity display.
When the “SETTING A MAXIMUM NUMBER OF COPIES.” key is
pressed, the following display will appear.
1.
Input the number using the 10-key pad.
●
A number from 1 to 999 can be set.
2.
Press the “OK” key.
KEY OPERATOR PROGRAMS
KEY OPERATOR PROGRAMS
ADD OR CHANGE EXTRA
PRESET RATIOS.
SELECT THE RATIO TO BE ADDED OR CHANGED AND
SET NEW PRESET RATIO.
REDUCTION
(25~99)
ENLARGEMENT
(101~800)
60
OK
KEY OPERATOR PROGRAMS
SETTING A MAXIMUM
NUMBER OF COPIES.
INPUT THE NUMBER AND PRESS [OK].
MAXIMUM NUMBER OF COPIES
(1~999)
OK
999
KEY OPERATOR’S GUIDE
Key operator programs
8-16
CHAPTER
8
KEY OPERATOR PROGRAMS
Initial Margin Shift Setting
Set the initial margin shift value with this program.
When the “INITIAL MARGIN SHIFT SETTING.” key is pressed, the
following display will appear.
When the “INITIAL MARGIN SHIFT SETTING.” key is pressed, the
following display will appear.
1.
Adjust the value for each side using the
and
keys.
●
The value can be set from 0 mm to 20 mm in 1 mm increments
(0" to 1" in 1/8" increments).
(0" to 1" in 1/8" increments).
●
If an optional duplex module (AR-DU1) is not installed in the AR-
281, the value for the reverse side (side 2) is not displayed.
281, the value for the reverse side (side 2) is not displayed.
2.
Press the “OK” key.
Erase Width Adjustment
Set the initial setting of the amount of the erase area with this program.
When the “ERASE WIDTH ADJUSTMENT.” key is pressed, the
following display will appear.
When the “ERASE WIDTH ADJUSTMENT.” key is pressed, the
following display will appear.
1.
Adjust the values for the edge erase mode and centre
erase mode using the
erase mode using the
and
keys.
●
The values can be set from 0 mm to 20 mm in 1 mm increments
(0" to 1" in 1/8" increments).
(0" to 1" in 1/8" increments).
2.
Press the “OK” key.
OK
CANCEL
KEY OPERATOR PROGRAMS
INITIAL MARGIN SHIFT
SETTING.
SET THE INITIAL MARGIN SHIFT.
SIDE 1
(0~20)
mm
mm
SIDE 2
(0~20)
mm
mm
10
10
OK
KEY OPERATOR PROGRAMS
ERASE WIDTH
ADJUSTMENT.
SET THE INITIAL ERASE WIDTH.
EDGE ERASE
(0~20)
mm
mm
CENTRE ERASE
(0~20)
mm
mm
OK
10
10
KEY OPERATOR’S GUIDE
Key operator programs
8-17
CHAPTER
8
KEY OPERATOR PROGRAMS
Initial Status Setting
The copier will assume the initial settings when it is turned on, when the
CLEAR ALL (
CLEAR ALL (
CA
) key is pressed, or when the auto clear interval has
elapsed after a copy run. Use this program to establish the initial
settings.
When the “INITIAL STATUS SETTING.” key is pressed, the following
display will appear.
settings.
When the “INITIAL STATUS SETTING.” key is pressed, the following
display will appear.
To establish new initial settings
1.
Press the “ESTABLISH NEW INITIAL SETTINGS.” key.
2.
Select all initial settings on the operation panel.
●
The following functions cannot be set:
Number of copies, XY zoom, automatic copy ratio selection,
interrupt, special functions, information, stapling position (for the
optional finisher (AR-FN1N only)) and LCD contrast.
Number of copies, XY zoom, automatic copy ratio selection,
interrupt, special functions, information, stapling position (for the
optional finisher (AR-FN1N only)) and LCD contrast.
3.
Press the “OK” key.
To return to the factory default settings
Press the “RETURN TO THE FACTORY DEFAULT SETTINGS.”
key.
key.
Stream Feeding Mode
This program is used to enable the stream feeding mode of the
document feeder. When the stream feeding mode is enabled, additional
originals which are set in the document feeder tray within 5 seconds
after the previous original was fed will be fed and copied automatically.
document feeder. When the stream feeding mode is enabled, additional
originals which are set in the document feeder tray within 5 seconds
after the previous original was fed will be fed and copied automatically.
To enable the stream feeding mode, press the check box of
“STREAM FEEDING MODE.” to display a check mark in the
check box.
To disable this mode, press the check box of this program
again to clear the check mark in the check box.
“STREAM FEEDING MODE.” to display a check mark in the
check box.
To disable this mode, press the check box of this program
again to clear the check mark in the check box.
●
The stream feeding mode will only function when the group mode has
been selected.
been selected.
KEY OPERATOR PROGRAMS
INITIAL STATUS SETTING.
SET THE INITIAL STATUS.
ESTABLISH NEW INITIAL
SETTINGS.
RETURN TO THE FACTORY DEFAULT
SETTINGS.
OK
1/4
1/4
KEY OPERATOR’S GUIDE
Key operator programs
8-18
CHAPTER
8
Staple Position Setting
This program is used to select the initial stapling position for the
optional finisher (AR-FN1N only).
When the “STAPLE POSITION SETTING.” key is pressed, the following
display will appear.
optional finisher (AR-FN1N only).
When the “STAPLE POSITION SETTING.” key is pressed, the following
display will appear.
1.
Select the desired stapling position on the touch panel.
2.
Press the “OK” key.
Date Format Setting
This program is used to set the initial date format for the date function.
When the “DATE FORMAT SETTING.” key is pressed, the following
display will appear.
When the “DATE FORMAT SETTING.” key is pressed, the following
display will appear.
1.
Select the desired date format on the touch panel.
●
The date formats displayed on the touch panel may be different
from the illustration above depending on the country or region.
from the illustration above depending on the country or region.
2.
Press the “OK” key.
KEY OPERATOR PROGRAMS
KEY OPERATOR PROGRAMS
STAPLE POSITION
SETTING.
OK
KEY OPERATOR PROGRAMS
23 April, 1998
April 23, 1998
23/04/98
04/23/98
DATE FORMAT SETTING.
OK
KEY OPERATOR’S GUIDE
Key operator programs
Click on the first or last page to see other AR-286 (serv.man10) service manuals if exist.