Sharp AR-285 (serv.man36) User Manual / Operation Manual ▷ View online
8-21
CHAPTER
8
KEY OPERATOR PROGRAMS
TIMER SETTINGS
The programs of this category are used to set the timers for some
functions. These programs can be selected by pressing the “TIMER
SETTINGS” key and then selecting the desired program key.
functions. These programs can be selected by pressing the “TIMER
SETTINGS” key and then selecting the desired program key.
Auto Power Shut-off Timer
The auto power shut-off mode is a function to turn off the power
automatically once a programmed length of time has elapsed without
any copier operation after the last copy of a run is made or power is
turned on.
This function lowers the user’s electricity bill, reduces waste of natural
resources, and cuts down on environmental pollution.
The programmed time is set to 60 minutes for this function on
completion of shipment from the factory. The default time can be
changed optionally within the prescribed range of time. We suggest
you set the most appropriate time according to your usage pattern.
Use this program to set the time interval. The time until auto power
shut-off occurs can be set in 10 minute increments up to a 4 hour
maximum.
When the “AUTO POWER SHUT-OFF TIMER.” key is pressed, the
following display will appear.
automatically once a programmed length of time has elapsed without
any copier operation after the last copy of a run is made or power is
turned on.
This function lowers the user’s electricity bill, reduces waste of natural
resources, and cuts down on environmental pollution.
The programmed time is set to 60 minutes for this function on
completion of shipment from the factory. The default time can be
changed optionally within the prescribed range of time. We suggest
you set the most appropriate time according to your usage pattern.
Use this program to set the time interval. The time until auto power
shut-off occurs can be set in 10 minute increments up to a 4 hour
maximum.
When the “AUTO POWER SHUT-OFF TIMER.” key is pressed, the
following display will appear.
1.
Enter the time interval using the
and
keys.
2.
Press the “OK” key.
Auto Clear Setting
Use this program to set the time interval to return the copier to the initial
settings after the last copy of a run has been completed. The time can
be set from 10 to 240 seconds in 10 second increments.
When the “AUTO CLEAR SETTING.” key is pressed, the following
display will appear.
settings after the last copy of a run has been completed. The time can
be set from 10 to 240 seconds in 10 second increments.
When the “AUTO CLEAR SETTING.” key is pressed, the following
display will appear.
1.
Set the desired time interval using the
and
keys.
●
To disable the auto clear, press the check box of “CANCEL
TIMER” to display a check mark in the check box.
TIMER” to display a check mark in the check box.
2.
Press the “OK” key.
KEY OPERATOR PROGRAMS
AUTO POWER SHUT-OFF
TIMER.
SET THE TIME INTERVAL FROM LAST COPY
UNTIL POWER OFF IN 10 MIN. INCREMENTS.
60
(10~240)
min.
OK
TIME:
KEY OPERATOR PROGRAMS
AUTO CLEAR SETTING.
SET THE TIME FOR AUTO CLEAR.
CANCEL TIMER
60
(10~240)
sec.
OK
TIME:
KEY OPERATOR’S GUIDE
Key operator programs
8-22
CHAPTER
8
KEY OPERATOR PROGRAMS
Preheat Mode Setting
Preheat mode functions to control the power consumption by lowering
the temperature of the fusing unit to a programmed level once a
programmed length of time has elapsed without any copier operation
after the last copy of a run is made or power is turned on. This function
lowers user’s electricity bill, reduces waste of natural resources, and
cuts down on environmental pollution. The programmed time is set to
15 minutes for this function on completion of shipment from the
factory. The default time can be changed optionally within the prescribed
range of time. We suggest you set the most appropriate time according
to your usage pattern.
This program is used to set the time that elapses before the copier
enters the preheat mode after copying is completed. The interval can
be set between 1 and 30 minutes in 1 minute increments.
When the “PREHEAT MODE SETTING.” key is pressed, the following
display will appear.
the temperature of the fusing unit to a programmed level once a
programmed length of time has elapsed without any copier operation
after the last copy of a run is made or power is turned on. This function
lowers user’s electricity bill, reduces waste of natural resources, and
cuts down on environmental pollution. The programmed time is set to
15 minutes for this function on completion of shipment from the
factory. The default time can be changed optionally within the prescribed
range of time. We suggest you set the most appropriate time according
to your usage pattern.
This program is used to set the time that elapses before the copier
enters the preheat mode after copying is completed. The interval can
be set between 1 and 30 minutes in 1 minute increments.
When the “PREHEAT MODE SETTING.” key is pressed, the following
display will appear.
1.
Set the desired time interval using the
and
keys.
2.
Press the “OK” key.
Message Time Setting
This program is used to adjust the length of time that messages are
displayed in the range of 1 to 12 seconds in 1 second increments.
When the “MESSAGE TIME SETTING.” key is pressed, the following
display will appear.
displayed in the range of 1 to 12 seconds in 1 second increments.
When the “MESSAGE TIME SETTING.” key is pressed, the following
display will appear.
1.
Set the time using the
and
keys.
2.
Press the “OK” key.
KEY OPERATOR PROGRAMS
PREHEAT MODE SETTING.
SET THE TIME FOR PREHEAT MODE.
15
(1~30)
min.
OK
TIME:
KEY OPERATOR PROGRAMS
MESSAGE TIME SETTING.
SET THE TIME FOR MESSAGES.
6
(1~12)
sec.
OK
TIME:
KEY OPERATOR’S GUIDE
Key operator programs
8-23
CHAPTER
8
ENABLE/DISABLE SETTINGS
The programs of this category are used to enable or disable some
functions. These programs can be set or cancelled by pressing the
check box of each program.
functions. These programs can be set or cancelled by pressing the
check box of each program.
Disabling of Auto Paper Selection
This program is used to prevent automatic paper selection. When
disabled, the copier will not automatically select a paper tray containing
paper that matches the size of the original placed on the document
glass or in the document feeder.
disabled, the copier will not automatically select a paper tray containing
paper that matches the size of the original placed on the document
glass or in the document feeder.
To disable auto paper selection, press the check box of
“DISABLING OF AUTO PAPER SELECTION.” to display a
check mark in the check box.
To restore this function, press the check box of this program
again to clear the check mark in the check box.
“DISABLING OF AUTO PAPER SELECTION.” to display a
check mark in the check box.
To restore this function, press the check box of this program
again to clear the check mark in the check box.
Disabling of Auto Tray Switching
This program prevents automatic switching between the paper trays.
To disable auto tray switching, press the check box of
“DISABLING OF AUTO TRAY SWITCHING.” to display a
check mark in the check box.
To restore this function, press the check box of this program
again to clear the check mark in the check box.
“DISABLING OF AUTO TRAY SWITCHING.” to display a
check mark in the check box.
To restore this function, press the check box of this program
again to clear the check mark in the check box.
Disabling of Bypass-Tray in Duplex Copy
This program is used to disable the use of the bypass tray when
making duplex copies.
making duplex copies.
To disable use of the bypass tray when making duplex
copies, press the check box of “DISABLING OF BYPASS-
TRAY IN DUPLEX COPY.” to display a check mark in the
check box.
To restore use of the bypass tray, press the check box of this
program again to clear the check mark in the check box.
copies, press the check box of “DISABLING OF BYPASS-
TRAY IN DUPLEX COPY.” to display a check mark in the
check box.
To restore use of the bypass tray, press the check box of this
program again to clear the check mark in the check box.
KEY OPERATOR PROGRAMS
KEY OPERATOR’S GUIDE
Key operator programs
8-24
CHAPTER
8
KEY OPERATOR PROGRAMS
Disabling Deletion of Job Programs
This program is used to prevent stored programs from being replaced
or deleted.
or deleted.
To prevent job programs stored in memory from being
replaced or deleted, press the check box of “DISABLING
DELETION OF JOB PROGRAMS.” to display a check mark in
the check box.
To allow replacement/deletion, press the check box of this
program again to clear the check mark in the check box.
replaced or deleted, press the check box of “DISABLING
DELETION OF JOB PROGRAMS.” to display a check mark in
the check box.
To allow replacement/deletion, press the check box of this
program again to clear the check mark in the check box.
Disabling of Document Feeder
This program is used to prevent the use of the document feeder when
it malfunctions.
it malfunctions.
To prohibit use of the document feeder, press the check box
of “DISABLING OF DOCUMENT FEEDER.” to display a check
mark in the check box.
To enable use of the document feeder, press the check box
of this program again to clear the check mark in the check
box.
of “DISABLING OF DOCUMENT FEEDER.” to display a check
mark in the check box.
To enable use of the document feeder, press the check box
of this program again to clear the check mark in the check
box.
Disabling of Duplex Copying
This program is used to enable or disable the duplex system. If a
malfunction occurs within the duplex system of the copier, the system
can be disabled until it is serviced. The rest of the copier in the
meantime will remain operable.
(In the AR-280, the duplex system is optional.)
malfunction occurs within the duplex system of the copier, the system
can be disabled until it is serviced. The rest of the copier in the
meantime will remain operable.
(In the AR-280, the duplex system is optional.)
To disable the duplex system, press the check box of
“DISABLING OF DUPLEX COPYING.” to display a check
mark in the check box.
To enable the duplex system, press the check box of this
program again to clear the check mark in the check box.
“DISABLING OF DUPLEX COPYING.” to display a check
mark in the check box.
To enable the duplex system, press the check box of this
program again to clear the check mark in the check box.
KEY OPERATOR’S GUIDE
Key operator programs
Click on the first or last page to see other AR-285 (serv.man36) service manuals if exist.