Sharp AR-285 (serv.man36) User Manual / Operation Manual ▷ View online
8-13
CHAPTER
8
To set a limit for all accounts
1.
Press the “LIMIT” (ALL ACCOUNTS) key on the touch
panel.
panel.
●
“ALL” will appear under “ACCOUNT NUMBER”.
2.
Enter the upper limit (max. 999,999) for all accounts.
●
To cancel the limit for all accounts, proceed to step 3 without
entering a limit.
entering a limit.
3.
Press the “ENTER” key.
4.
Press the “OK” key to exit the program.
Account Number Security
This program is used to make it difficult for users to gain access to
accounts by entering code numbers through trial and error. If this
program is selected and an operator enters three successive invalid
account numbers, the copier will not accept another number for one
minute and the message “
accounts by entering code numbers through trial and error. If this
program is selected and an operator enters three successive invalid
account numbers, the copier will not accept another number for one
minute and the message “
PLEASE SEE YOUR KEY OPERATOR FOR
ASSISTANCE.
” will appear.
To enable the account number security function, press the
check box of “ACCOUNT NUMBER SECURITY.” to display a
check mark in the check box.
To disable this function, press the check box of this program
again to clear the check mark in the check box.
check box of “ACCOUNT NUMBER SECURITY.” to display a
check mark in the check box.
To disable this function, press the check box of this program
again to clear the check mark in the check box.
KEY OPERATOR PROGRAMS
KEY OPERATOR’S GUIDE
Key operator programs
8-14
CHAPTER
8
OTHER FUNCTION SETTINGS
The programs of this category are used to adjust various settings of
copier functions. These programs can be selected by pressing the
“OTHER FUNCTION SETTINGS” key and then selecting the desired
program key.
copier functions. These programs can be selected by pressing the
“OTHER FUNCTION SETTINGS” key and then selecting the desired
program key.
Key Operator Code Number Change
See page 8-2, KEY OPERATOR CODE NUMBER.
Exposure Adjustment
Use this program to lighten or darken copies in the automatic exposure
mode. The factory setting is level 3.
When the “EXPOSURE ADJUSTMENT.” key is pressed, the following
display will appear.
mode. The factory setting is level 3.
When the “EXPOSURE ADJUSTMENT.” key is pressed, the following
display will appear.
1.
Adjust the exposure using the
and
keys.
2.
Press the “OK” key.
Toner Save Mode
The toner save mode will reduce toner consumption by approxi-
mately 10% in the automatic, text, and text/photo exposure
modes. Copies will be lighter but still adequate for general use.
Selection of this mode does not affect the photo mode.
mately 10% in the automatic, text, and text/photo exposure
modes. Copies will be lighter but still adequate for general use.
Selection of this mode does not affect the photo mode.
To turn on the toner save mode, press the check box of
“TONER SAVE MODE.” to display a check mark in the
check box.
To turn off the toner save mode, press the check box of
this program again to clear the check mark in the check
box.
“TONER SAVE MODE.” to display a check mark in the
check box.
To turn off the toner save mode, press the check box of
this program again to clear the check mark in the check
box.
KEY OPERATOR PROGRAMS
KEY OPERATOR PROGRAMS
EXPOSURE ADJUSTMENT.
AUTO
OK
KEY OPERATOR’S GUIDE
Key operator programs
8-15
CHAPTER
8
Add or Change Extra Preset Ratios
Two extra preset copy ratios can be added within both the reduction
range (25% to 99%) and the enlargement range (101% to 800%). Only
added preset copy ratios can be changed. The standard preset copy
ratios are fixed in memory and cannot be changed.
When the “ADD OR CHANGE EXTRA PRESET RATIOS.” key is
pressed, the following display will appear.
range (25% to 99%) and the enlargement range (101% to 800%). Only
added preset copy ratios can be changed. The standard preset copy
ratios are fixed in memory and cannot be changed.
When the “ADD OR CHANGE EXTRA PRESET RATIOS.” key is
pressed, the following display will appear.
1.
Press a key under “REDUCTION” or “ENLARGEMENT”
on the touch panel.
on the touch panel.
●
The selected key will be highlighted.
2.
Use the
and
keys to set the desired copy ratio.
●
To decrease or increase the copy ratio rapidly, press and hold
the
the
or
key.
●
To add or change other extra preset copy ratios, repeat steps 1
and 2.
and 2.
●
To cancel an extra preset ratio, select the copy ratio and press
the CLEAR (
C
) key.
3.
Press the “OK” key.
Setting a Maximum Number of Copies
Use this program to limit the maximum number of copies per copy run
which can be input in the copy quantity display.
When the “SETTING A MAXIMUM NUMBER OF COPIES.” key is
pressed, the following display will appear.
which can be input in the copy quantity display.
When the “SETTING A MAXIMUM NUMBER OF COPIES.” key is
pressed, the following display will appear.
1.
Input the number using the 10-key pad.
●
A number from 1 to 999 can be set.
2.
Press the “OK” key.
KEY OPERATOR PROGRAMS
KEY OPERATOR PROGRAMS
ADD OR CHANGE EXTRA
PRESET RATIOS.
SELECT THE RATIO TO BE ADDED OR CHANGED AND
SET NEW PRESET RATIO.
REDUCTION
(25~99)
ENLARGEMENT
(101~800)
60
OK
KEY OPERATOR PROGRAMS
SETTING A MAXIMUM
NUMBER OF COPIES.
INPUT THE NUMBER AND PRESS [OK].
MAXIMUM NUMBER OF COPIES
(1~999)
OK
999
KEY OPERATOR’S GUIDE
Key operator programs
8-16
CHAPTER
8
KEY OPERATOR PROGRAMS
Initial Margin Shift Setting
Set the initial margin shift value with this program.
When the “INITIAL MARGIN SHIFT SETTING.” key is pressed, the
following display will appear.
When the “INITIAL MARGIN SHIFT SETTING.” key is pressed, the
following display will appear.
1.
Adjust the value for each side using the
and
keys.
●
The value can be set from 0 mm to 20 mm in 1 mm increments
(0" to 1" in 1/8" increments).
(0" to 1" in 1/8" increments).
●
If an optional duplex module (AR-DU1) is not installed in the AR-
280, the value for the reverse side (side 2) is not displayed.
280, the value for the reverse side (side 2) is not displayed.
2.
Press the “OK” key.
Erase Width Adjustment
Set the initial setting of the amount of the erase area with this program.
When the “ERASE WIDTH ADJUSTMENT.” key is pressed, the
following display will appear.
When the “ERASE WIDTH ADJUSTMENT.” key is pressed, the
following display will appear.
1.
Adjust the values for the edge erase mode and centre
erase mode using the
erase mode using the
and
keys.
●
The values can be set from 0 mm to 20 mm in 1 mm increments
(0" to 1" in 1/8" increments).
(0" to 1" in 1/8" increments).
2.
Press the “OK” key.
OK
CANCEL
KEY OPERATOR PROGRAMS
INITIAL MARGIN SHIFT
SETTING.
SET THE INITIAL MARGIN SHIFT.
SIDE 1
(0~20)
mm
mm
SIDE 2
(0~20)
mm
mm
10
10
OK
KEY OPERATOR PROGRAMS
ERASE WIDTH
ADJUSTMENT.
SET THE INITIAL ERASE WIDTH.
EDGE ERASE
(0~20)
mm
mm
CENTRE ERASE
(0~20)
mm
mm
OK
10
10
KEY OPERATOR’S GUIDE
Key operator programs
Click on the first or last page to see other AR-285 (serv.man36) service manuals if exist.