DOWNLOAD Sharp AR-161 (serv.man7) Service Manual ↓ Size: 247.78 KB | Pages: 6 in PDF or view online for FREE

6) Remove the pawls (3 positions) of the protective cover at therear

side.

7) Remove the protective cover.

•

Pull the cover in the arrow direction to remove.

8) Insert the developer cartridge.

•

Gently insert the developer cartridge along the guide until it
locks.

9) Fix the developer cartridge with the fixing screw which is packed

together with the machine.

10) Close the front cover A, then close the side cover B.

•

When closing the front cover, gently press the both sides.

•

When closing the side cover, hold the knob.

•

When closing the covers, be sure to close the front cover first,
then close the side cover. If closed in a wrong sequence, the
covers may be broken.

1) Lift the knob and gently pull out the tray.

2) Hold the paper pressure plate and turn the fixing screw in the

arrow direction.

3) Store the fixing pin and the fixing screw in the tray.

•

Store the fixing screw which was removed in the above proce-
dure 2 and the fixing screw which was removed in procedure 2
of 2.

•

Removal of protective material and fixing screw in the storage
place in the tray.

A

B

Pressure

plate

lock

Screw

AR-161

AR-160/161 FM/E [5] UNPACKING AND INSTALLATION 10/20/1998

5 – 2

1) Gently lift and pull out the paper tray until it stops.

2) Push the pressure plate down until it locks in place.

3) Squeeze the lock lever of the front guide and slide the front guide

to match the width of the paper.

4) Move the left guide to the appropriate slot as marked on the tray.

•

When using 11" 

×

17" copy paper, store the left guide in the slot

at the left front of the paper tray.

5) Load copy paper into the tray.

6) Place the paper size plate in the front of the paper tray.

•

The paper size indication which shows through the slot on the
front of the copier should match the selected paper size.

7) Push the paper tray firmly back into the copier.

8) To set the selected paper size, press and hold down the PAPER

SIZE ENTER key. The selected paper feed location indicator and
the corresponding paper size (which has been set) indicator will
blink. All other indicators will go out.

•

For paper size setting, ensure that the COPY mode has been
selected. However, if printer or facsimile output is being per-
formed, paper size setting cannot be made even in the COPY
mode.

9) Use the TRAY SELECT key to select the paper tray of which the

paper size has been changed.

•

Each time the TRAY SELECT key is pressed, a paper tray is
indicated with a blinking paper feed location indicator. If an
optional paper feed unit is not installed, this operation is not
needed.

10) Use the ORIGINAL SIZE ENTER key to select the paper size

which is set.

•

Each time the ORIGINAL SIZE ENTER key is pressed, a
paper size will be indicated with a blinking paper size in-
dicator.

11) Press the START key and then the PAPER SIZE ENTER key.

•

To change the paper size setting of another tray, repeat steps
9 to 10 after pressing the START key.

Front guide

Left guide

AR-161

AR-160/161 FM/E [5] UNPACKING AND INSTALLATION 10/20/1998

5 – 3

1) Gently lift and pull out the paper tray until it stops.

2) Push the pressure plate down until it locks in place.

3) Squeeze the lock lever of the front guide and slide the front guide

to match the width of the paper.

4) Move the left guide to the appropriate slot as marked on the tray.

•

When using 11" 

×

17" copy paper, store the left guide in the slot

at the left front of the paper tray.

5) Load copy paper into the tray.

6) Place the paper size plate in the front of the paper tray.

•

The paper size indication which shows through the slot on the
front of the copier should match the selected paper size.

7) Push the paper tray firmly back into the copier.

8) To set the selected paper size, press and hold down the PAPER

SIZE ENTER key. The selected paper feed location indicator and
the corresponding paper size (which has been set) indicator will
blink. All other indicators will go out.

•

For paper size setting, ensure that the COPY mode has been
selected. However, if printer or facsimile output is being per-
formed, paper size setting cannot be made even in the COPY
mode.

9) Use the TRAY SELECT key to select the paper tray of which the

paper size has been changed.

•

Each time the TRAY SELECT key is pressed, a paper tray is
indicated with a blinking paper feed location indicator. If an
optional paper feed unit is not installed, this operation is not
needed.

10) Use the ORIGINAL SIZE ENTER key to select the paper size

which is set.

•

Each time the ORIGINAL SIZE ENTER key is pressed, a
paper size will be indicated with a blinking paper size in-
dicator.

11) Press the START key and then the PAPER SIZE ENTER key.

•

To change the paper size setting of another tray, repeat steps
9 to 10 after pressing the START key.

Front guide

Left guide

AR-161

AR-160/161 FM/E [5] UNPACKING AND INSTALLATION 10/20/1998

5 – 3

1) Gently lift and pull out the paper tray until it stops.

2) Push the pressure plate down until it locks in place.

3) Squeeze the lock lever of the front guide and slide the front guide

to match the width of the paper.

4) Move the left guide to the appropriate slot as marked on the tray.

•

When using 11" 

×

17" copy paper, store the left guide in the slot

at the left front of the paper tray.

5) Load copy paper into the tray.

6) Place the paper size plate in the front of the paper tray.

•

The paper size indication which shows through the slot on the
front of the copier should match the selected paper size.

7) Push the paper tray firmly back into the copier.

8) To set the selected paper size, press and hold down the PAPER

SIZE ENTER key. The selected paper feed location indicator and
the corresponding paper size (which has been set) indicator will
blink. All other indicators will go out.

•

For paper size setting, ensure that the COPY mode has been
selected. However, if printer or facsimile output is being per-
formed, paper size setting cannot be made even in the COPY
mode.

9) Use the TRAY SELECT key to select the paper tray of which the

paper size has been changed.

•

Each time the TRAY SELECT key is pressed, a paper tray is
indicated with a blinking paper feed location indicator. If an
optional paper feed unit is not installed, this operation is not
needed.

10) Use the ORIGINAL SIZE ENTER key to select the paper size

which is set.

•

Each time the ORIGINAL SIZE ENTER key is pressed, a
paper size will be indicated with a blinking paper size in-
dicator.

11) Press the START key and then the PAPER SIZE ENTER key.

•

To change the paper size setting of another tray, repeat steps
9 to 10 after pressing the START key.

Front guide

Left guide

AR-161

AR-160/161 FM/E [5] UNPACKING AND INSTALLATION 10/20/1998

5 – 3