Sharp AR-151 (serv.man3) Service Manual ▷ View online
Main code
Sub code
Content
22
01
Maintenance/mini-maintenance counter display
The display is the same as the total counter value display.
When the destination is set to other than Japan AB series, the maintenance counter is displayed.
When the destination is set to Japan AB series, the mini-maintenance counter is displayed. The display is the
same as the total counter value display.
The display is the same as the total counter value display.
When the destination is set to other than Japan AB series, the maintenance counter is displayed.
When the destination is set to Japan AB series, the mini-maintenance counter is displayed. The display is the
same as the total counter value display.
02
Maintenance/mini-maintenance preset display
The preset value corresponding to the code set in 21-01 and 21-02.
The display is the same as the total counter value display.
When the destination is set to other than Japan AB series, the maintenance preset value is displayed.
When the destination is set to Japan AB series, the mini-maintenance preset value is displayed.
The preset value corresponding to the code set in 21-01 and 21-02.
The display is the same as the total counter value display.
When the destination is set to other than Japan AB series, the maintenance preset value is displayed.
When the destination is set to Japan AB series, the mini-maintenance preset value is displayed.
04
Jam total counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
05
Total counter display
The total count value is dispalyed in 3 digits
The total count value is dispalyed in 3 digits
×
2 times repeatedly.
<Display example: 12345>
012
012
→
Blank
→
345
→
Blank
→
012
0.7s 0.3s 0.7s 1.0s 0.7s
06
Developer counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
08
SPF counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
12
Drum counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
14
P-ROM versiondisplay
The P-ROM version is displayed in 3 digits on the value display section.
(AR, DM, PCL models: 100% Zoom lamp display)
The P-ROM version is displayed in 3 digits on the value display section.
(AR, DM, PCL models: 100% Zoom lamp display)
17
Copy counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
18
Printer counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
20
Fax print counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
21
Scanner counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
22
SPF jam total counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
23
FAX reception counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
24
FAX transmission counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
24
01
Jam total counter clear
When the PRINT switch is pressed, the jam total count value is reset to 0.
When the PRINT switch is pressed, the jam total count value is reset to 0.
04
SPF counter clear
When the PRINT switch is pressed, the SPF count value is reset to 0.
When the PRINT switch is pressed, the SPF count value is reset to 0.
06
Developer counter clear
When the PRINT switch is pressed, the drum count value is reset to 0.
When the PRINT switch is pressed, the drum count value is reset to 0.
07
Drum counter clear
When the PRINT switch is pressed, the drum count value is reset to 0.
When the PRINT switch is pressed, the drum count value is reset to 0.
08
Copy counter clear
When the PRINT switch is pressed, the copy count value is reset to 0.
When the PRINT switch is pressed, the copy count value is reset to 0.
09
Printer counter clear
When the PRINT switch is pressed, the printer count value is reset to 0.
When the PRINT switch is pressed, the printer count value is reset to 0.
10
FAX transmission/reception counter clear
When the PRINT switch is pressed, the FAX transmission/reception count value is reset to 0.
When the PRINT switch is pressed, the FAX transmission/reception count value is reset to 0.
11
FAX print counter clear
When the PRINT switch is pressed, the Fax print-out count value is reset to 0.
When the PRINT switch is pressed, the Fax print-out count value is reset to 0.
13
Scanner counter clear
When the PRINT switch is pressed, the scanner count value is reset to 0.
When the PRINT switch is pressed, the scanner count value is reset to 0.
AR-F152
9 – 4
Main code
Sub code
Content
24
14
SPF jam total counter clear
When the PRINT switch is pressed, the SPF jam total count value is reset to 0.
When the PRINT switch is pressed, the SPF jam total count value is reset to 0.
25
01
Main motor system ON + Cooling fan low speed (For the duplex model, the duplex motor is simultaneously
turned on.)
(Operation/Procedure)
When the START key is pressed, the main motor is rotated for 30 sec.
To save toner consumption, the different operations are executed depending on installation of the developing unit.
turned on.)
(Operation/Procedure)
When the START key is pressed, the main motor is rotated for 30 sec.
To save toner consumption, the different operations are executed depending on installation of the developing unit.
⋅
When the developing unit is installed, the developing bias, the main charger, and the grid are also outputted.
⋅
When the developing unit is not installed, only the motor is rotated.
∗
Do not turn on the door open/close switch forcibly to execute this simulation.
10
Polygon motor ON
(Operation/Procedure)
When the START key is pressed, the polygon motor is operated for 30sec.
(Operation/Procedure)
When the START key is pressed, the polygon motor is operated for 30sec.
26
01
Manual feed setup
(Operation/Procedure)
1. When this simulation is executed, the currently set bypass code number is displayed.
2. Enter the code number corresponding to the bypass and press the START key, and the setting will be
changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set bypass code number is displayed.
2. Enter the code number corresponding to the bypass and press the START key, and the setting will be
changed.
02
SPF setup
When this simulation is executed, the currently set SPF code number is displayed. Enter the code number of the
SPF to be set and press the PRINT switch. The setup is changed.
When this simulation is executed, the currently set SPF code number is displayed. Enter the code number of the
SPF to be set and press the PRINT switch. The setup is changed.
03
Second cassette setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the second cassette is displayed.
2. Enter the code number and press the start key. The setting is changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the second cassette is displayed.
2. Enter the code number and press the start key. The setting is changed.
04
Machine duplex setup
(Operation/procedure)
1. When this simulation is executed, the currently set duplex code number is displayed.
2. Enter the code number corresponding to the duplex and press the ENTER key, and the setup will be changed.
(Operation/procedure)
1. When this simulation is executed, the currently set duplex code number is displayed.
2. Enter the code number corresponding to the duplex and press the ENTER key, and the setup will be changed.
06
Destination setup
(Operation/Procedure)
1. When this simulation is executed, the currently set destination code number is displayed.
2. Enter the code number corresponding to the destination and press the START key, and the setting will be
changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set destination code number is displayed.
2. Enter the code number corresponding to the destination and press the START key, and the setting will be
changed.
Code number
Bypass
0
Single bypass
1
Multi bypass
Code No.
SPF
0
Without SPF
1
With SPF (Setup is required when installing FAX.)
2
With RSPF
Code number
Second cassette
0
Without second cassette
1
With second cassette
Code number
Duplex
0
Without Duplex
1
With Duplex
Code number
Destination
0
Inch series
1
EX AB series
2
Japan AB series
AR-F152
9 – 5
Main code
Sub code
Content
26
07
Machine conditions check
(Operation/Procedure)
When this simulation is executed, the current machine setting is displayed.
(Operation/Procedure)
When this simulation is executed, the current machine setting is displayed.
20
Rear edge void setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of rear edge void setting is displayed.
2. Enter the code number of rear edge void setting and press the START key, and the setting will be changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of rear edge void setting is displayed.
2. Enter the code number of rear edge void setting and press the START key, and the setting will be changed.
30
CE mark conformity control ON/OFF setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of CE mark application is displayed.
2. Enter the code number of CE mark application and press the START key, and the setting will be changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of CE mark application is displayed.
2. Enter the code number of CE mark application and press the START key, and the setting will be changed.
37
Cancel of stop at developer life over
When this simulation is executed, the current set code is displayed. Enter a new code and press the PRINT
switch, and the entered code is registered.
When this simulation is executed, the current set code is displayed. Enter a new code and press the PRINT
switch, and the entered code is registered.
39
Memory capacity setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
40
Polygon motor OFF time setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
CPM
Copy quantity display
10 cpm
10
12 cpm
12
15 cpm
15
The machine type is shown with the lamp display.
No setup: None
BTA-A: AE mode lamp ON
BTA-B: TEXT mode lamp ON
BTA-C: Photo mode lamp ON
No setup: None
BTA-A: AE mode lamp ON
BTA-B: TEXT mode lamp ON
BTA-C: Photo mode lamp ON
Code number
Rear edge void setting
0
Rear edge void allowed
1
Rear edge void not allowed
Code number
CE mark application setting
0
CE mark application control OFF
1
CE mark application control ON
Code number
Setting
0
Stop at developer life over
1
Stop cancel at developer life over
Code number
Setting
0
No memory
1
4 Mbyte
2
6 Mbyte
Code number
Setting
0
0 sec
1
30 sec
2
60 sec
3
90 sec
AR-F152
9 – 6
Main code
Sub code
Content
26
42
Transfer ON timing control setup
(Operation / Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed. (For any number different
from the following ones, the default time is automatically set.)
(Operation / Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed. (For any number different
from the following ones, the default time is automatically set.)
43
Side void setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the side void amount is displayed.
2. Enter the code number and press the start key. The setting is changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the side void amount is displayed.
2. Enter the code number and press the start key. The setting is changed.
44
SPF document rear edge read setup + Fax document rear edge scan setup.
When this simulation is executed, the currently set code number is displayed. Enter the desired code number
and press the START key, and the display will be changed. The document rear edge scanning area in SPF
reduction (less than 100%) copy is changed.
and press the START key, and the display will be changed. The document rear edge scanning area in SPF
reduction (less than 100%) copy is changed.
The code number is changeable in the range of 0 – 8.
The default value is 4, and 2 mm of the document rear edge is cut.
When the value is changed by 1, the area is changed by 1 mm.
The default value is 4, and 2 mm of the document rear edge is cut.
When the value is changed by 1, the area is changed by 1 mm.
47
FAX document rear edge scan setup
When this simulation is executed, the currently set code number is displayed. Enter the desired code number
and press the print switch, and the setup is switched. The scan area at the rear edge of FAX original with SPF
is changed according to the entered code number.
Code number is in the range of 0 – 8.
The default is 4. When set to the default, the area of about 2 mm from the rear edge of the original is cut out.
When the value is changed by 1, the dimension is changed by about 1 mm.
When this simulation is executed, the currently set code number is displayed. Enter the desired code number
and press the print switch, and the setup is switched. The scan area at the rear edge of FAX original with SPF
is changed according to the entered code number.
Code number is in the range of 0 – 8.
The default is 4. When set to the default, the area of about 2 mm from the rear edge of the original is cut out.
When the value is changed by 1, the dimension is changed by about 1 mm.
55
CRUM destination display
When this simulation is executed, the current setup of the CRUM destination stored in the machine is displayed.
When this simulation is executed, the current setup of the CRUM destination stored in the machine is displayed.
Code number
Setting
0
Default (330 msec)
1
–40 msec
2
–30 msec
3
–20 msec
4
–10 msec
5
Default (330 msec)
6
+10 msec
7
+20 msec
8
+30 msec
9
+40 msec
Code number
Setting
0
0 mm
1
0.5 mm
2
1.0 mm
3
1.5 mm
4
2.0 mm *Default
5
2.5 mm
6
3.0 mm
7
3.5 mm
8
4.0 mm
9
4.5 mm
10
5.0 mm
Code number
Setting
00
No setup
01
BTA-A
02
BTA-B
03
BTA-C
AR-F152
9 – 7
Click on the first or last page to see other AR-151 (serv.man3) service manuals if exist.