DOWNLOAD Sharp AR-151 (serv.man3) Service Manual ↓ Size: 6.51 MB | Pages: 127 in PDF or view online for FREE

Note: These items are factory adjusted when shipping according to

FCC standards. Therefore, do not change the setting in the
market.

(1) Dial pulse transmission test

1) Execute SIM 66-13 in FAX mode.
2) Execute the dial pulse mode according to the instructions on the

LCD display.

SELECT SIGNAL

1:PULSE  2:DTMF

3) Set the make time.

INPUT MAKE TIME

(0–15)              

4) Select the dial to be transmitted.

Default: 0123456789#
(After deleting with the clear key, it can be set to any desired
value.)

5) Transmission is started from the line.

SEND yyPPS xxm s

1:YES 2:NO

SENDING yyPPS xxm s

SIM

Soft SW

Initial
value

Set value

Dial
pulse
make
time

10
PPS

FAX
mode
66-13

SW67-
1 – 4

40ms
(14)

SW set value:
0 – 15
Make time:
25 – 41ms

1ms
step
(Binary
input)

(2) DTMF signal transmission level adjustment

1) Execute SIM 66-13 in the FAX mode.
2) Execute the DTMF mode according to the instructions on the

LCD display.

SELECT SIGNAL

1:PULSE  2:DTMF

3) Select the signal transmission level.

The signal transmission level is classified into two groups: the
high group, and the low group.
Transmission can be made with either of default and the soft
SW set value.

SELECT HIGH LEVEL

1:DEFAULT 2:SOFT SW.

SELECT LOW LEVEL

1:DEFAULT 2:SOFT SW.

4) The transmission level can be set when the following menu is

displayed on the LCD. (et value 1 = 0.5dB change)

INPUT VALUE

(0–15)              

(This value is returned to the original value when the simulation
mode is canceled.)

5) Select the dial signal to be transmitted.

Default: 0123456789#
(After deleting with the clear key, it can be set to any desired value.)

6) Start transmission from the line.

H:xx   L:yy

1:YES 2:NO

SENDING DTMF

xx: High group soft SW set value
yy: Low group soft SW set value

SIM

Soft SW

Initial
value

Set value

DTMF
trans-
mission
level

High
group

(FAX
mode)
66-13
(Test
only)

SW53-
1 – 4

3.5dB
(7)

SW set
value: 0 –
15
Transmis-
sion level: 0
– 7.5db

0.5ms
step
(Binary
input)

Low
group

SW53-
5 – 8

3.5dB
(7)

AR-F152

8 – 12

The simulations for the AR-F152 (with Fax functions) are shown in bold fonts.

Sim

No.

Kind of

main code

Sub

code

Operation

01

Optical
system

01

Mirror scan operation

02

SPF
Individual
load
operation

02
03
04
05

06
07

SPF sensor status display
Motor ON
Paper feed solenoid ON
Pressure release solenoid ON
(RSPF)
Resist clutch ON (RSPF)
Gate solenoid ON (RSPF)

05

Lamp ON
check

01
02

03

Operation panel display check
Fusing lamp ON + Cooling fan
HIGH/LOW speed
Copy lamp ON

06

Machine
individual
load
operation

01
02

Paper feed solenoid ON
Resist solenoid ON

07

Aging

01

06

Warm up display and aging with
jam
Intermittent aging

08

High
voltage
output check

01
02
03
06

Developing bias
Main charger (Grid high)
Grid voltage (Low)
Transfer charger

10

Other

None

Toner motor aging

14

Trouble
reset

None

Cancel troubles other than U2

16

U2 trouble
reset

None

Cancel of U2 trouble

20

Maintenance 
counter
clear

01

Maintenance/mini-maintenance
counter clear

21

Counter
setup
(When
maintenance)

01
02

Maintenance cycle setup
Mini-maintenance cycle setup

22

Counter
display

01

02

04
05
06
08
12
14
17
18
20
21
22
23
24

Maintenance/mini-maintenance
counter display
Maintenance/mini-maintenance
preset display
Jam total counter display
Total counter display
Developer counter display
SPF counter display
Drum counter display
P-ROM version display
Copy counter display
Printer counter display
FAX print counter display
Scanner counter display
SPF jam total counter display
FAX reception counter display
FAX transmission counter
display

24

Special
counter
clear

01
04
06
07
08
09
10

11
13
14

Jam total counter clear
SPF counter clear
Developer counter clear
Drum counter clear
Copy counter clear
Printer counter clear
FAX transmission/reception
counter clear
FAX print counter clear
Scanner counter clear
SPF jam total counter clear

25

Main motor
ON

01

10

Main motor system ON + Cooling
fan low speed (For the duplex
model, the duplex motor is
simultaneously turned on.)
Polygon motor ON

Sim

No.

Kind of

main code

Sub

code

Operation

26

Various
setup

01
02
03
04
06
07
20
30

37
39
40
42
43
44

47

55

Manual feed setup
SPF setup
Second cassette setup
Machine duplex setup
Destination setup
Machine conditions check
Rear edge void setup
CE mark conformity control
ON/OFF setup
Cancel of stop at developer over
Memory capacity setup
Polygon motor OFF time setup
Transfer ON timing control setup
Side void setup
SPF document rear edge read
setup
FAX document rear edge scan
setup
CRUM destination display

30

Sensor
operation
check
(Standard
provision)

01

Paper sensor status display

43

Fusing
temperature
setup

01
04
05

09

Normal copy
Fusing temperature setup 2
Duplex mode fusing temperature
setup
Postcard size paper fusing control
setup

46

Exposure
adjustment

01
12
13

Copy density adjustment
FAX density overall adjustment
FAX density adjustment
(Standard mode)
FAX density adjustment (Fine
character mode)
FAX density adjustment (Super
Fine mode)

γ

48

Magnification 
ratio
correction

01

Front/rear scan direction

50

Lead edge
adjustment

01

10

18

19

Lead edge image position
adjustment
Paper lead edge/rear edge void
adjustment
Paper center offset +
OC/Document center offset +
SPF document center offset
Memory reverse position
adjustment
Duplex copy rear edge void
adjustment

51

Timing
adjustment

02
06

Resist quantity adjustment
SPF exposure correction

61

Laser
system
operation

03

Polygon motor check
(HSYNC output check)

63

Shading

01

Shading check

64

Self print

01

Self print only with the engine (1
by 2 mode)

67

Program
Download

14

PCL PWB program download

AR-F152

9 – 1

Input method: Clear key 

→

 Exposure Select key 

→

 Clear key 

→

 Exposure Select key

Main code

Sub code

Content

01

01

Mirror scan operation
(Operation/Procedure)
1.   When this simulation is executed, the mirror home position is detected.

2.

When the _START key is pressed, scanning is executed at the speed corresponding to the currently set copy
magnification ratio.
The copy magnification ratio can be arbitrarily set with the magnification ratio select key/zoom key.

02

02

SPF sensor status display
ON/OFF of the sensors in the SPF can be checked with the following lamps.

03

Motor ON
(Operation/Procedure)
When the start key is pressed, the SPF motor rotates for 10 sec at the speed corresponding to the currently set
magnification ratio.

04

Paper feed solenoid ON
(Operation/Procedure)
When the start key is pressed, the SPF paper feed solenoid repeats ON (500 ms) and OFF (500 ms) 20 times.

05

Pressure release solenoid ON (RSPF)
(Operation/Procedure)
When the start key is pressed, the RSPF document transport solenoid (SPFS) repeats ON (500 ms) and OFF
(500 ms) 20 times.

06

Resist clutch ON (RSPF)
(Operation/Procedure)
When the start key is pressed, the RSPF resist clutch (SRRC) repeats ON (500 ms) and OFF (500 ms) 20
times.

07

Gate solenoid ON (RSPF)
(Operation/Procedure)
When the start key is pressed, the RSPF gate solenoid (SGS) repeats ON (500 ms) and OFF (500 ms) 20
times.

05

01

Operation panel display check
When the PRINT switch is pressed, the LED on the operation panel is lighted for 5 sec. The LED on the FAX
panel and the LCD black background are displayed simultaneously.

02

Fusing lamp ON + cooling fan HIGH/LOW speed
(Operation/Procedure)
When the START key is pressed, the fusing lamp repeats ON (500ms) and OFF (500msec) 5 times.
During this period, the cooling fan rotates in the high speed mode. After completion of the operation, the cooling
fan rotates in the low speed mode.

03

Copy lamp ON
(Operation/Procedure)
When the START key is pressed, the copy lamp is lighted for 5 sec.

06

01

Paper feed solenoid ON
(Operation/Procedure)
When the START key is pressed, the paper feed solenoid selected by the tray select key repeats ON (500ms)
and OFF (500ms) 20 times.

02

Resist solenoid ON
(Operation/Procedure)
When the START key is pressed, the resist solenoid (RRS) repeats ON (500ms) and OFF (500ms) 20 times.

Sensor name

Display lamp

Mirror home position sensor

OPC drum cartridge replacement lamp

Display

Sensor

Toner cartridge replacement lamp

Document set detection (SPID)

Jam lamp

SPF document transport detection (SPPD)

Developer replacement lamp

SPF cover open detection (SCOD)

SPF jam lamp

SPF open/close detection (SDSW)
FAX document size detection
Paper size detection

SPF lamp

FAX/SPF B4 size detection (SB4D)

AR-F152

9 – 2

Main code

Sub code

Content

07

01

Warm-up display and aging with jam
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. Warm-up time is counted and displayed every second on the copy quantity display.
3. After completion of warm-up, the time count is stopped and the ready lamp is lighted.
4. Press the clear key to clear the warm-up time display, set the copy quantity, and press the START key, and
the machine will copy the set quantity repeatedly.

06

Intermittent aging
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. After completion of warm-up, the ready lamp is lighted.
3. Set the copy quantity and press the START key, and the machine will copy the set quantity repeatedly.
4. After 3 sec of the interval time from completion of copying the set quantity, the machine will resume copying.
5. The above operation 4 is repeated.

08

01

Developing bias
(Operation/Procedure)
When the START key is pressed, the developing bias is outputted for 30 sec.

02

Main charger (Grid high)
(Operation/Procedure)
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage HIGH mode.

03

Grid voltage (Low)
(Operation/Procedure)
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage LOW mode.

06

Transfer charger
(Operation/Procedure)
When the START key is pressed, the transfer charger output is supplied for 30 sec.

10

None

Toner motor aging
(Operation/Procedure)
When the START key is pressed, the toner motor output is supplied for 30 sec.

14

None

Cancel of troubles other than U2
(Operation/Procedure)
After canceling the trouble, the simulation is also automatically canceled.

16

None

Cancel of U2 trouble
(Operation/Procedure)
1. When the START key is pressed, the EEPROM total counter check sum is rewritten and the trouble is
canceled.
2. After canceling the trouble, the simulation is also automatically canceled.

20

01

Maintenance/mini-maintenance counter clear
When the Print switch is pressed, the maintenance counter is cleared, and 000000 is displayed. When the
destination has been set to Japan AB series, the mini-maintenance counter is cleared.

21

01

Maintenance cycle setup
The currently set maintenance cycle code is displayed (initial display), and the set data is stored.

02

Mini-maintenance cycle setup (Valid only when the destination is set to Japan AB series.)
The current set code of maintenance cycle is displayed (Initial display), and the set data is stored.

Code

Setup

0

3,000 sheets

1

6,000 sheets

2

9,000 sheets

3

13,000 sheets

4

25,000 sheets

5

Free (999,999 sheets) 

∗

 Default

Code

Setup

0

5,000 sheets   

∗

 Default

1

10,000 sheets

2

Free (999,999 sheets)

AR-F152

9 – 3